Land Rover Series 2 & 3 Parts

Bottom cover seal

Rivet - a mechanical fastener used within the body and chassis assembly to join thin sheet metal and panel components. Nominal size 3/16" (4.8 mm)...

Hydraulic Tappet fitted within the V8 petrol engine valve train, where it maintains zero valve clearance automatically. Engine oil pressure fills ...

Self-Tapping Screw – No. 6 × 3/4 in used to secure interior trim and panel fixings, such as the dash panel and upper fascia mouldings. Being self-...

Spare Wheel Cover for an externally mounted spare wheel sized 7.50x16 (235/85R16). Constructed from soft vinyl, it shields the spare wheel and tyr...

Oil Filler Pipe Gasket seals the joint between the oil filler pipe and the engine front (timing) cover. Fitted at the filler pipe mounting flange,...

Oil Pump Lock Tab, part of the engine oil pump assembly. The lock tab is a tab washer fitted under the oil pump retaining fastener; once the faste...

Clevis Pin for the handbrake (transmission parking brake) linkage. This 22mm clevis pin connects the handbrake operating rod to the relay lever, t...

Transfer Box Output Mud Shield Shield that fits over the transfer box output flange to protect the output shaft oil seal from mud, water and debris...

Heater Duct, left-hand side, within the heater air distribution system. Routes air from the heater assembly to the floor-level outlet beneath the ...

Nut - 10/32" UNF A nut with a #10-32 UNF (Unified National Fine) internal thread, run onto a matching UNF bolt or stud to clamp the joint.

Bolt - a hexagonal-head bolt with a 5/16" UNC (Unified Coarse) imperial thread and a 3/4" length. Used as an engine-assembly fixing, including cams...

Diff Pinion Taper Roller Bearing is the inner pinion taper roller bearing in the Salisbury axle differential. It supports the pinion shaft where i...

Pinion Bearing (Outer) for the Salisbury axle differential. It is the outer of the pair of taper roller bearings that carry the drive pinion, seate...

Bolt is an M8 x 80 mm threaded fastener used to clamp two components together at a bolted joint. It is tightened into a threaded hole or secured w...

Bolt with a 1/4" UNF (Unified Fine) thread. A threaded steel fastener used to secure body panels and ancillary fittings.

Hex Head Bolt - 1/4" UNF thread, 5/8" long, with a hexagonal head. A general-purpose imperial fastener with a Unified Fine (UNF) thread form, driv...

Clutch Slave Cylinder, part of the hydraulic clutch release circuit. The slave cylinder receives fluid pressure from the clutch master cylinder an...

Snatch Block - a winch recovery pulley used to redirect a winch line or to double its effective pulling capacity. Rated for a 10-tonne working load...

Pan Head Screw - a machine screw with a low, rounded-top head and a flat bearing face, used as a general-purpose fixing. Metric M6 thread with a 1...

Piston for the 2.25L 4-cylinder petrol engine, forming the reciprocating member within the cylinder bore that transmits combustion pressure through...

Brake Shoe Screw - a retaining screw within the drum brake assembly that secures the brake shoe in position. It holds the shoe located against the...

Wiper Cable Tube - LHD is a guide tube in the cable-and-rack windscreen wiper system, in the left-hand-drive configuration. It houses and routes t...

Air cleaner to carburettor hose

Transfer Box Lever Lock Nut used to secure the selector linkage at the transfer case. This half nut (thin profile locking nut) threads onto the sel...

Cleat Rope Hook Body Side All and Classic (Softtop) - Series Defender

Side Window Seal is the rubber glazing seal that secures and weatherproofs the fixed side window glass within its body aperture. Part of the body ...

Door Seal - Bottom for the left-hand front door, forming part of the door-aperture weather sealing. The seal fits along the lower edge of the door...

Wing Fixing Plate is a three-stud captive stud plate used in the front body mounting assembly, where it secures the front wing to the radiator (fro...

Spring Washer, M8, a split ring washer used with M8 bolts and nuts to prevent fastener loosening caused by vibration and cyclical loading. The spl...

Rear Stop/Tail Lamp - LED, Smoked - LED combined stop and tail lamp with a smoked lens, supplied as a complete sealed unit to replace the standard ...

Piston for the 2.25L four-cylinder diesel engine, operating within the cylinder block as part of the piston and connecting-rod assembly. The pisto...

Breather Hose connecting the camshaft cover to the inlet manifold, part of the engine's crankcase ventilation system. It routes crankcase blow-by ...

Number Plate Mounting bracket for securing a front number plate, measuring 405mm wide by 110mm deep. The bracket provides a flat mounting face for ...

High-Tensile Bolt with a 5/16" UNF (Unified National Fine) imperial thread and a 1-1/4" shank length. A hex-head fastener manufactured to a high-t...

Bolt - V8 Inlet Manifold is the fastener that secures the inlet manifold on the Rover V8 petrol engine. It clamps the inlet manifold to the cylind...

Headlamp Screw is a fastener used in the front headlamp assembly. It secures the headlamp unit and rim within their mounting, holding the lamp in ...

Carb overhaul kit 175CD V8 Zenith Stromberg

Oil Seal - Clutch Cross Shaft for Series 1 and Series 2 Land Rover vehicles (1948-1971). The clutch cross shaft passes through the bellhousing and...

Core Plug for the engine casting. Core plugs seal the core holes left in the cylinder block after the casting sand is removed during manufacture. ...

Driving Member is the front hub drive flange that couples the axle halfshaft to the road wheel hub. It bolts to the outer face of the front hub, w...

Brake Pedal Return Spring for the pedal box assembly, fitted to servo-assisted braking systems. The spring returns the brake pedal to its rest pos...

Diesel Injector for the fuel injection system, delivering metered, atomised fuel from the injection pump into the engine. Fitted to the 2.25L and ...

Manifold Clamp - a clamping plate that secures the manifold to the cylinder head. It fits over the manifold flange and draws down onto the cylinde...

Differential Pinion Bearing Spacer used in the axle differential assembly across a broad range of Land Rover models from 1965 onwards. This spacer...

Door Seal for the front door, part of the door sealing system. Runs around the front door aperture to seal the gap between the door and the body s...

Heater Cable operates the tap-type heater control valve in the heating and ventilation system. It connects the dashboard heater control to the tap...

Corner Capping - galvanised - right-hand (offside) roof corner. This galvanised steel capping fits over the offside rear roof corner, covering and...