Land Rover Series 2 & 3 Parts

Camshaft for the 2.25L 4-cylinder petrol engine valve train. Running in the cylinder block and driven from the crankshaft by the timing gear, the ...

Rocker Cover Washer used at the rocker (valve) cover fixing on the cylinder head. Fitted beneath the rocker cover retaining nut, the washer seals ...

Rocker Shaft Bush in the cylinder head valvetrain. The bush is pressed into a rocker pedestal and provides the bearing surface that supports the r...

Flywheel Bolt securing the flywheel to the rear flange of the crankshaft. Threaded 7/16 UNF with a 7/8 in shank length, the bolt clamps the flywhe...

Sealing Washer is a copper joint washer used in multiple engine and ancillary applications across the Land Rover range, including as a sealing wash...

Hose Clip for securing flexible hoses to pipes and stubs throughout the Land Rover. Tightening the clip compresses the hose onto the stub to form a...

Exhaust Bracket for the exhaust system mounting. The bracket secures and locates the exhaust pipework against the underbody, supporting the system...

Oil Relief Valve Sealing Washer seals the oil pressure relief valve within the engine oil pump assembly. It is fitted at the relief valve in the l...

Ballast Resistor Resistor in the ignition primary circuit of the 3.5L V8 petrol engine. Wired in series with the ignition coil, it drops the suppl...

Floor-Mounted Headlamp Dipswitch for Land Rover Series 2A vehicles. This foot-operated switch mounts to the cab floor and controls switching betwe...

Oil Pump Assembly for the engine lubrication system of the 4-cylinder non-TDi engine range. Driven from the engine, the pump draws oil from the su...

Spare Wheel Carrier is a fixed rear-door-mounted bracket that supports and retains the spare wheel. It bolts directly to the rear door and locates...

Output Shaft Bearing for the LT76 gearbox, a taper roller bearing that supports the rear output shaft. It locates the output shaft within the gear...

Layshaft Bearing for the early-type LT76 gearbox. It supports the layshaft (countershaft) within the gearbox, carrying the cluster gear that trans...

Steering Relay Arm - Upper is the upper lever of the steering relay unit, the vertical relay mounted on the front chassis crossmember that transfer...

Fuel Cap closes and seals the fuel tank filler neck on petrol applications. It uses a two-lug bayonet fixing that locates and locks into the fille...

Seat Belt Bracket for the front seat belt, lower mounting, right-hand side. This bracket bolts to the seat box and provides the lower anchorage po...

Keep your Land Rovers interior clean and tidy with a loadspace mat. Ribbed rubber / 1,560 x 920 x 3mm Defender 110 - excluded 3 door commercial ...

Barrel Lock and Key, Set of Two for the door locks, supplied as two keyed lock barrels each with a key. Each barrel is the cylinder the key turns ...

Tailgate Hook for the lower hinged tailboard, right-hand side. This pigtail (spiral) hook mounts on the body and retains the tailgate support stra...

Contact Set for the Lucas 25D distributor in the ignition system of the 2.25L and 2.6L petrol engines. The contact set (breaker points) opens and ...

Synchro Hub for the 3rd/4th gear synchroniser assembly in the Series-type manual gearbox (LT76). The hub carries the synchroniser mechanism that m...

Dipstick Tube - the guide tube through which the engine oil level dipstick passes down into the sump. It locates in the cylinder block and directs...

Gearbox Thrust Washer

Crankshaft Thrust Washer controls crankshaft end-float - the axial movement of the crankshaft within the block - at the centre main bearing. The w...

Shackle Plate for the rear leaf spring shackle assembly, in the extended (long) form used on the heavier-duty chassis. It locates the outer eye of...

Valve Collet for the valve gear of the 2.25L petrol and 2.0L diesel engines, used with single-groove valve stems. The split collets seat in the gr...

Door Pillar Repair Bracket for the front left-hand (nearside) door pillar. A welded repair section that renews the front door pillar at the bulkhe...

Body Seal - a moulded rubber weather seal in the body & chassis assembly. It closes the gap between adjacent body panels to exclude water, dus...

Rear Quarter Panel for the right-hand side, part of the rear body structure. This is the outer body panel that forms the rear side of the vehicle ...

Rotor Arm - Ducellier Type for the ignition distributor assembly. This rotor arm fits the Ducellier-type distributor and rotates inside the distri...

Mirror Glass - the replacement reflective glass for the exterior door mirror. It seats into the mirror head on its backing plate, restoring a clear...

Piston Assembly - 0.040" Oversize for the 2.25L 4-cylinder petrol engine as fitted to the Land Rover Defender and Series II, IIA, and III. Designe...

Plate - LH is the rear axle brake pipe shield (bracket) for the left-hand side. It mounts on the rear axle and shields the rigid brake pipe runnin...

Plate - RH is the rear axle brake pipe shield (bracket) for the right-hand side. It mounts on the rear axle and shields the rigid brake pipe runni...

Seat Back - Outer - Standard - Black for the left and right outer positions of the three-abreast front bench seat in Land Rover Series vehicles. T...

Seat Back - Inner - the centre backrest of the three-piece front bench seat, trimmed in black vinyl. Fitted between the two outer seat backs, it p...

Seat Back and Headrest for the outer front seat, in the deluxe pattern and finished in black. This is the upholstered backrest (squab) the occupant...

Rear Light Guard - Single - Black is a steel mesh protective guard for a single rear lamp. It bolts over the rear lamp lens to shield it from impa...

Rear Crossmember Fixing Kit - stainless steel - provides the fasteners that secure the rear crossmember and rear body mounting to the chassis, repl...

Thrust Washer and Pin for the LT95 four-speed gearbox, 3.55mm thickness. This selective-thickness washer, with its locating pin, sets the end-float...

Door Hinge Kit - 2nd Row - a complete set of second row door hinges with fixings, forming part of the door mounting hardware. Each hinge bolts to ...

Connecting Rod Bearing Set - a set of big-end bearing shells for the Rover V8 petrol engine. The connecting rod bearings are the split shell beari...

Main Bearing Set - a set of crankshaft main bearing shells for the Rover V8 petrol engine. The main bearings are the split shell bearings that car...

Crown Wheel & Pinion Set - the final-drive gear pair housed within the axle differential. The pinion takes drive from the propshaft and turns t...

Cylinder Head Bolt Washer seats under the head of a 7/16in cylinder head bolt on the Rover V8 petrol engine. It distributes clamping load across t...

Driveshaft Oilpump