Land Rover Series 2 & 3 Parts

Differential Pinion Bearing Shim - 0.066 in, for use in the Rover 10-spline rear differential. This shim sets the preload on the pinion outer beari...

Diff Pinion Taper Roller Bearing is the inner pinion taper roller bearing in the Salisbury axle differential. It supports the pinion shaft where i...

Brake Lining - Rear is a replacement friction lining for the rear drum brake assembly on long-wheelbase Land Rover models, covering 109-inch, 110-i...

Pedal Shaft is the transverse shaft on which both the clutch pedal and brake pedal are mounted within the cab, on vehicles without a brake servo. ...

Circlip is a split retaining ring that locates on the reverse shaft of the LT95 gearbox. It seats into a machined groove to axially retain the rev...

Handbrake Carrier Spacer for the handbrake assembly on Series II, IIA, III and Defender 90/110. This spacer fits within the handbrake carrier mech...

Gearbox Selector Circlip - a retaining circlip within the manual transmission gear selector mechanism. The circlip locates on its shaft to secure ...

Rubber Washer - Seat Backrest for Land Rover Series and Defender models. This rubber washer is used in the seat backrest assembly, fitting beneath...

Drop Plate Strengthener for the towing equipment assembly. It acts as a spacer and strengthener for the towing jaw and the towing jaw/ball fixings...

Distributor - 3.5L V8 Twin Carb is the ignition distributor for the Rover 3.5L V8 petrol engine in twin-carburetter configuration. The distributor...

Rocker Assembly Aluminium - LH

Door Capping - Galvanised - RH for the Defender 110 door assembly. This galvanised steel door capping fits along the upper edge of the right-hand ...

Washer is a nylon door hinge washer used on the hinge fixing bolts. It fits over the hinge bolt as a low-friction spacer between the moving hinge ...

Sump - 2.25 Petrol/Diesel - 2.5 Petrol is the engine oil sump (oil pan) for the 2.25L 4-cylinder petrol, 2.25L 4-cylinder diesel, and 2.5L 4-cylind...

Vacuum Actuator O-Ring for the LT95 4-speed gearbox. This O-ring seals the vacuum actuator fitted to the LT95 transfer case mechanism, used on V8-p...

Clevis Pin for the bonnet stay. Forms the pivot at the upper end of the bonnet prop, retaining the stay to the bonnet.

Bonnet Lock Striker for the hand-operated bonnet latch assembly. This striker pin is the fixed catch component in the bonnet locking system, engag...

Exhaust Silencer for right-hand-drive applications, constructed in stainless steel. Part of the exhaust system, this silencer attenuates combustio...

Camshaft Bearing Set for the Rover 3.5L V8 petrol engine. Supplies the bearing shells that support the camshaft as it runs within the cylinder blo...

Door Hinge Kit for the front doors - stainless steel hinges that mount each front door to the body hinge pillar, replacing the original hinges. Th...

Synchro Cone (Baulk Ring) - LT95 4-Speed Gearbox This synchro cone, also known as a baulk ring, is a component of the synchroniser assembly within...

Diesel Fuel Filter Plug Seal - a sealing ring for the drain plug on the diesel fuel filter and sedimentor. It seals the drain/bleed plug against t...

Seat Frame for the adjustable driver's seat on Series II and Series III models. This structural frame forms the base of the driver's seat assembly.

Nyloc Nut M5 - M5 hex nyloc (nylon insert) locknut. The nylon insert creates friction against the thread to resist loosening under vibration. Stan...

Spare Wheel Cover in plain black vinyl, sized to fit a 600 x 16 spare wheel and tyre (roughly a 195/80 R15 metric equivalent). It slips over the m...

Seat Base Corner Capping in plastic. Fitted at the outer corners of the front seat base frame, this capping provides a neat finished edge and prote...

Windscreen Wiper Ferrule for the windscreen wiper mechanism — the splined bush that couples the wiper arm to the drive spindle. The ferrule fits o...

Differential Pinion Bearing Shim - 0.070 in, for use in the Rover 10-spline rear differential. This shim sets the preload on the pinion outer beari...

Anti-Roll Bar Link & Shock Bush Kit renews the compliant mounting bushes in the anti-roll bar link and shock absorber mounting points within th...

Rocker Cover Screw - Long for the Rover 3.5L V8 engine. This long 1/4" UNC x 1-5/16" screw secures the rocker cover to the cylinder head on the Ro...

Cylinder Head Bolt is the short-length head bolt that clamps the cylinder head to the block on the 2.25L and 2.5L 4-cylinder petrol engines. The h...

Cable Clip for securing wiring harnesses and cables in Land Rover vehicles. Sold individually.

Blanking Plug - Metric - Cylinder Head Rear seals the rear coolant gallery opening in the cylinder head on Land Rover 4-cylinder engines. The rear...

Front Fuel Tank Outrigger is a chassis outrigger welded to the main frame rail, located at the rear of the front fuel tank to support and locate th...

O-Ring for use in two distinct applications on classic Land Rover engines. On the Series IIA 2.6L 6-cylinder engine, this O-ring seals the cylinde...

Door Latch Shim - Rear - a packing shim for the rear door anti-burst latch, part of the door lock and handle assembly. Fitted behind the latch on ...

Tappet Guide (guide only) locates and retains the tappet roller assembly within the engine block, maintaining correct alignment of the tappet as it...

Crankshaft with Bearings for the 2.25L 4-cylinder petrol engine. The crankshaft converts the reciprocating motion of the pistons into rotational o...

Exhaust Tailpipe forming the final section of the exhaust system on the 109" Stage One V8. This pipe routes exhaust gases rearward from the silenc...

7 inch high low beam headlight LHD black, with U shape parking light, (PAIR)

Blanking Plug - plastic plug sealing a 1-1/4" (32mm) diameter aperture in the rear cross member. Installs into unused or access holes in the bodys...

Rocker Cover Screw for the Rover V8 petrol engine. This 1/4" UNC screw secures the valve (rocker) cover to the cylinder head. The rocker cover per...

Fuel Filler Screw is a 2BA x 3/8" fastener used to secure the fuel filler fitting. It retains the fuel filler to the body panel; the companion nut...

Braided Earth Strap with Battery Clamp - 300mm for the vehicle electrical grounding circuit. This braided copper earth strap is fitted with an int...

Bolt - 5/16" UNF x 5/8" is a general-purpose hexagon-head set bolt in 5/16 UNF (Unified National Fine) thread, 5/8 inch in length. Used across engi...

Flywheel Bolt, 7/16" UNC x 1" hexagonal head, securing the flywheel to the rear crankshaft flange. Used on V8 petrol engines with manual transmiss...

Cylinder Head Bolt - a 7/16" UNC x 2.71" medium-type bolt for the Rover V8, part of the cylinder head fixings. This is the medium-length head bolt...

Countersunk Screw - a machine screw with a flat, cone-shaped head that seats flush with the surface it fixes, leaving no proud edge. Metric M6 thr...