Land Rover Series 2 & 3 Parts

Hex-head screw, 1/4" UNF thread, 3/4" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and socke...

Drain plug

Gear Knob - LT95 is the hand grip fitted to the main gear lever of the LT95 4-speed gearbox. It threads onto the top of the gear lever and provide...

Exhaust Clamp Plate for the exhaust system, used at the front-pipe and catalyst joint. The plate works together with a U-bolt to draw the exhaust c...

Timing Cover Mudshield is the pressed shield that fits over the timing cover at the front of the engine. It screens the timing case and front pull...

Swivel Housing Kit for the front axle swivel assembly, covering one side of the axle. This is the later configuration, with the steering arm mounte...

Anti-Burst Door Lock for the left-hand front door, the latch mechanism that secures the door to the body. The latch engages the striker on the doo...

Rear Crankshaft Packing Strip (T-Piece) forms part of the rear crankshaft oil seal arrangement at the back of the cylinder block. The T-piece pack...

Bolt with a 5/16" UNF (Unified National Fine) imperial thread and a 1-1/2" shank length. A hex-head fastener for general assembly and fixing appli...

Fuel Pump Repair Kit for overhauling the mechanical diaphragm lift pump on the 2.25 four-cylinder petrol engine. Wear in the pump internals reduce...

Head Gasket - 3.5L V8 - Metal is the cylinder head gasket for the 3.5L V8 petrol engine, sealing the joint between a cylinder head and the engine b...

Synchro Cone – LT76 is a synchroniser ring from the synchromesh assembly of the LT76 manual gearbox. It is the friction component that brings the g...

Joint Washer for the radiator cap, part of the engine cooling system. This sealing washer seats between the radiator cap and the filler neck, main...

Oil Filler Cap O-Ring seals the oil filler cap to the rocker cover. It forms an oil-tight seal at the cap-to-cover joint, preventing oil leakage a...

Transfer Box Intermediate Shaft Shim, 0.005in thick, used in the transfer box to set the end float of the intermediate gear on its shaft. Selectiv...

Fuel Pipe Olive for the fuel supply line. The olive is the compression ferrule that seats between the fuel pipe and its union fitting. When the un...

Exhaust Bracket for the exhaust system on left-hand drive vehicles. This bracket supports and locates the exhaust along its run beneath the vehicl...

Lock Plate for the rear drum brake shoe retainer. This fold-over tab plate locks the two screws that secure the brake shoe bottom retainer ring. I...

Gear Lever Retaining Spring The spring that retains the main gear lever in its ball housing on the gearbox top cover. It bears down on the lever's...

Double-Grooved Ball Bearing for the manual gearbox and transfer box. It supports and locates a rotating shaft within the casing, carrying the radia...

Service Kit - a complete engine service pack for the 2.25 litre petrol engine running Lucas fixed-points (25D) ignition. The kit gathers the consu...

Fuel Pump Diaphragm for the mechanical fuel pump on petrol engines, with a T-bar notched shaft for the later type of pump. This is the diaphragm o...

Tow Ball Step is a rear access step that locates over the tow ball, providing two tread levels to make reaching the rear door, load area or roof ea...

Exhaust Fitting Kit for a short-wheelbase exhaust system, left-hand drive configuration. The kit provides the mounting components and fixings need...

Thermostat - the coolant-flow control valve in the engine cooling system, with an 82°C opening temperature. Mounted in the thermostat housing at t...

Half Shaft – Rear LH – 10-Spline is the rear axle drive shaft for the left-hand side. It transmits drive from the differential out to the rear hub ...

Heater Hose for the rear of the heater circuit, carrying engine coolant between the heater pipe and the heater unit. This flat-section hose forms ...

Track Rod & Steering Damper Bush for the steering linkage, locating the steering damper at its mounting eye. The bush insulates the damper mou...

Front Bumper in galvanised steel, mounting across the front of the chassis frame. It bolts to the front chassis dumb-irons to provide front-end im...

Swivel Housing Stud with 7/16" BSF thread, fitted to the lower face of the front axle swivel housing. The stud secures the lower swivel pin bracke...

Turnbuckle is the semi-circular catch that fastens the seat box and rear tub locker lids down. It rotates over the mating hasp to hold the lid shu...

Gear Lever Housing The ball/socket housing for the main gear lever, mounted on the gearbox top cover (turret). It seats the spherical lower end of...

Inlet Valve - the poppet valve that seals the inlet port in the cylinder head and opens on the induction stroke to admit the incoming air charge to...

Radiator Overflow Hose carries coolant overflow away from the radiator filler neck. It connects to the overflow spigot on the radiator filler neck...

Injector Pipe - the high-pressure fuel line serving the No.4 cylinder on the 2.25L diesel. It carries metered fuel from the injection pump outlet ...

Cylinder Head Bolt - a clamping bolt securing the cylinder head to the engine block. It draws the head down onto the block to compress the head ga...

Oil Dipstick - engine oil level gauge for the 4-cylinder engine. Inserts into the dipstick tube to read the oil level in the sump, marked with min...

Primary Pinion Bearing for the manual gearbox, supporting the primary pinion (gearbox input shaft). The primary pinion transmits drive from the cl...

Heater Hose for the front of the heater circuit, carrying engine coolant between the engine feed and the heater unit. This flat-section hose forms...

Sliding Window Catch secures the sliding glass of the front door side window, locking the two panes together so the window can be held shut or fixe...

Swivel Housing Gaiter Kit in leather for the front axle swivel housings, supplied as an axle set to cover both sides. The gaiter encloses the swiv...

Reverse Lamp Lens is the clear lens that fits to the rear reverse (reversing) lamp assembly. It seals over the bulb and reflector and diffuses the...

Upper Rear Door Hinge, aluminium, for the rear end (tailgate) door, part of the body and door assembly. It is the upper of the two hinges that car...

Oil Pressure Sensor Monitors engine oil pressure in the lubrication circuit and signals the oil pressure gauge or warning lamp on the instrument pa...

Rear Fog Lamp for the rear lighting circuit, providing the high-intensity red rear light used to make the vehicle conspicuous from behind in poor v...

Window Channel

Universal Joint is a cross-type (spider) joint fitted within the propshaft assembly, transmitting rotational drive between opposing yokes while acc...

Axle Check Strap limits the downward travel of the rear axle, fitted within the rear suspension on the 1-Ton chassis running the Salisbury axle. I...