for Discounts / VAT
for Discounts & Correct VAT
Parts for Land Rover Series II, Series IIA, and Series III (1958 to 1985), covering 88-inch short wheelbase and 109-inch long wheelbase configurations. Genuine, OEM, and aftermarket options across engine, body, electrical, suspension, and brake categories. Stocked and shipped from The Hague as part of the full Land Rover Series parts catalogue.
What fits: Series II (1958 to 1961), Series IIA (1961 to 1971), Series III (1971 to 1985), SWB and LWB.
Universal Joint is a cross-type (spider) joint fitted within the propshaft assembly, transmitting rotational drive between opposing yokes while acc...
View full detailsTrack Rod End with left-hand thread, part of the steering linkage. The track rod end connects the track rod to the steering arm through a ball joi...
View full detailsTrack Rod End for the steering linkage, with a right-hand thread. The track rod end is a ball-jointed coupling at the end of the track rod that co...
View full detailsHex-head screw, 1/4" UNF thread, 3/4" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and socke...
View full detailsCore Plug for the rear of the camshaft bore in the V8 petrol cylinder block. The cup-type plug seals the machined opening at the rear of the camsh...
View full detailsStainless Braided Brake Hose Kit for the flexible sections of the hydraulic braking circuit, made to imperial thread specification and extended by ...
View full detailsDemister Tube Grommet is a moulded rubber grommet in the windscreen demister ducting that seals the demister hose where it passes through the lower...
View full detailsHandbrake Shoe - V8 - LT95 is a brake shoe for the transmission-mounted parking brake used with the LT95 four-speed gearbox. Rather than acting at...
View full detailsSump Gasket seals the joint between the sump (oil pan) and the base of the cylinder block on the 2.6L six-cylinder IOE petrol engine. It forms the...
View full detailsHeadlamp Surround — the chrome bezel that trims and retains the outer edge of a 7-inch round headlamp. A polished chrome ring fitted over the head...
View full detailsExhaust Clamp Plate for the exhaust system, used at the front-pipe and catalyst joint. The plate works together with a U-bolt to draw the exhaust c...
View full detailsPropshaft UJ Circlip - a retaining clip for the universal joint of the propeller shaft. It seats in the groove of the yoke ear and holds the beari...
View full detailsSteel ball 1/4"
Breather Set Screw secures the breather to the rocker cover within the engine crankcase ventilation arrangement. It retains the breather against t...
View full detailsCarburettor Gasket - a sealing gasket for the Zenith-Stromberg 175CD carburettor as fitted to the 3.5 litre V8. It seals a joint within the carbur...
View full detailsAlternator Brush Set replaces the carbon brushes in an ACR-type alternator, within the charging system. The brushes bear on the rotor slip rings a...
View full detailsWiper Arm - windscreen wiper arm, left-hand. The 7mm is the wide width of the arm, which sets the wiper-blade fitting - it is not a spindle size. ...
View full detailsSwivel Housing Kit for the front axle swivel assembly, covering one side of the axle. This is the later configuration, with the steering arm mounte...
View full detailsSealing ring
Footwell Repair Panel is a welded body repair panel for the left-hand (offside) footwell, replacing the corroded or damaged footwell section ahead ...
View full detailsDrive Screw - a No. 6 x 1/2" self-tapping drive screw used across door and facia assemblies. It secures the front door glass and window regulator,...
View full detailsSynchro Cone – LT76 is a synchroniser ring from the synchromesh assembly of the LT76 manual gearbox. It is the friction component that brings the g...
View full detailsAlternator Pulley mounts on the alternator drive shaft and is turned by the engine drive belt. It transfers rotation from the crankshaft belt driv...
View full detailsFuel Pipe Olive for the fuel supply line. The olive is the compression ferrule that seats between the fuel pipe and its union fitting. When the un...
View full detailsInterior Door Lock Button, right-hand, of the interior door furniture. The thumbscrew-type lock button that operates the door lock from inside the...
View full detailsTailgate Buffer - rubber buffer for the rear tailgate (tailboard). This rubber buffer cushions the tailgate where it meets the body, absorbing the...
View full detailsClutch Anchor Plate - a steel mounting plate within the clutch pedal box assembly. It anchors the clutch pedal pivot to the bulkhead, providing th...
View full detailsSealing Washer for the carburettor choke switch on petrol engine applications. Fitted at the choke switch, it seals the joint at the fitting to pr...
View full detailsGear Lever Retaining Spring The spring that retains the main gear lever in its ball housing on the gearbox top cover. It bears down on the lever's...
View full detailsDouble-Grooved Ball Bearing for the manual gearbox and transfer box. It supports and locates a rotating shaft within the casing, carrying the radia...
View full detailsCrankshaft Pulley for the 2.25L and 2.5L 4-cylinder petrol engine. It mounts on the nose of the crankshaft and drives the cooling fan, water pump a...
View full detailsInjector Leak-Off Pipe for the 2.25L and 2.5L naturally-aspirated diesel fuel injection circuit. This spill-return pipe connects the return unions ...
View full detailsCellular Dynamic Shock Absorber A long-travel rear damper that controls axle movement within the suspension, mounted between the chassis and the re...
View full detailsService Kit - a complete engine service pack for the 2.25 litre petrol engine running Lucas fixed-points (25D) ignition. The kit gathers the consu...
View full detailsTow Ball Step is a rear access step that locates over the tow ball, providing two tread levels to make reaching the rear door, load area or roof ea...
View full detailsFront Shackle Plate forms part of the front leaf-spring shackle assembly, connecting the road spring eye to the chassis mounting. The shackle allow...
View full detailsHeater Hose for the rear of the heater circuit, carrying engine coolant between the heater pipe and the heater unit. This flat-section hose forms ...
View full detailsFront Bumper in galvanised steel, mounting across the front of the chassis frame. It bolts to the front chassis dumb-irons to provide front-end im...
View full detailsEngine Push Rod for diesel engine valve actuation, operating within the cylinder head valve train. The push rod transmits motion from the camshaft...
View full detailsTurnbuckle is the semi-circular catch that fastens the seat box and rear tub locker lids down. It rotates over the mating hasp to hold the lid shu...
View full detailsGear Lever Housing The ball/socket housing for the main gear lever, mounted on the gearbox top cover (turret). It seats the spherical lower end of...
View full detailsHead Gasket Seals the cylinder head to the cylinder block on the pre-TDi 2.25L and 2.5L naturally aspirated and turbocharged diesel engines. It co...
View full detailsFront Shackle Plate forms part of the front leaf-spring shackle assembly, connecting the road spring eye to the chassis mounting. The shackle allow...
View full detailsInjector Pipe - the high-pressure fuel line serving the No.4 cylinder on the 2.25L diesel. It carries metered fuel from the injection pump outlet ...
View full detailsInjector Pipe No.2, a high-pressure delivery pipe in the diesel fuel injection system. The rigid steel pipe carries fuel under high pressure from ...
View full detailsDrain Plug for the gearbox, transfer box and axle casings. It threads into the drain point at the base of the casing to retain the oil in service, ...
View full detailsSpring Shackle Plate forms part of the rear leaf spring shackle assembly, pairing with the shackle pins and bushes to connect the swinging eye of t...
View full detailsSwivel Pin Housing Locking Plate mounts to the front axle swivel pin housing. It locks the swivel pin in position and provides the fixed stop that...
View full detailsParts for Land Rover Series II, Series IIA, and Series III, produced from 1958 to 1985. Covers short wheelbase (88-inch) and long wheelbase (109-inch) configurations. Series I is a separate collection. Use your Commission Number to confirm fitment before ordering.
This collection covers Land Rover Series II (1958 to 1961), Series IIA (1961 to 1971), and Series III (1971 to 1985) in both short wheelbase and long wheelbase configurations. It does not cover Series I vehicles. Series I parts are held in a separate collection.
The three generations in this collection share the same core body-on-frame ladder chassis, a two-speed transfer gearbox, and a four-speed manual main gearbox. Wheelbase options from Series II onward were 88 inches (short wheelbase, referred to as SWB) and 109 inches (long wheelbase, referred to as LWB). Parts compatibility is not uniform across the three generations, and wheelbase is a fitment variable for a significant number of components including body panels, wiring looms, propshafts, and floor sections.
The 2.25-litre petrol and diesel engines are shared across Series IIA and Series III, and engine internals for these units carry across both generations in most cases. Other components, including wiring configurations, swivel housing seals, and certain axle parts, differ between generations and between sub-variants within the Series III production run. A 1980 update introduced five main bearing crankshafts to the 2.25-litre engines. A 1982 update increased the Series III half shaft drive spline count from 10 to 24, which affects axle half shaft selection for late Series III vehicles.
LWB Series IIA models were available with a 2.6-litre straight-six petrol engine. Series III LWB models used the Salisbury rear axle as standard. The Stage 1 V8 variant, produced from 1979 to 1985, used a 3.5-litre Rover V8 and the LT95 gearbox; this was an LWB-only production variant with some component differences from standard Series III specification.
The Land Rover UK heritage pages cover the original design and production history of the Series family and are a useful background reference for owners identifying their vehicle's generation and specification.
Series Land Rovers do not carry a modern 17-digit VIN. Instead, each vehicle has a Commission Number stamped on a plate fixed to the bulkhead. This number encodes the series, engine type, wheelbase, and approximate build date. Confirming your Commission Number before ordering is the most reliable way to ensure parts match your specific vehicle.
The Land Rover Heritage Trust holds production records and Commission Number data for the full Series family and is the definitive reference for vehicle identification on older or incomplete builds.
If you are uncertain about your generation or wheelbase, contact Budget Parts with your Commission Number before placing an order. The team will confirm applicable fitment from the catalogue.
Fitment NotesParts compatibility across this collection varies by generation, wheelbase, and in some cases by build date within a generation. The table below summarises the key fitment variables.
| Generation | Production | Wheelbase options | Engines | Key fitment notes |
|---|---|---|---|---|
| Series II | 1958 to 1961 | 88-inch SWB, 109-inch LWB | 2.0-litre petrol (early), 2.25-litre petrol, 2.0-litre diesel | Some early SWB models used the Series I 2.0-litre engine |
| Series IIA | 1961 to 1971 | 88-inch SWB, 109-inch LWB | 2.25-litre petrol, 2.25-litre diesel, 2.6-litre I6 (LWB only) | Highest-volume sub-series; many mechanical parts cross to early Series III |
| Series III | 1971 to 1985 | 88-inch SWB, 109-inch LWB | 2.25-litre petrol, 2.25-litre diesel, 2.6-litre I6, 3.5-litre V8 petrol | Stage 1 V8 was LWB only (1979 to 1985); 1980 crank update and 1982 half shaft spline update affect part selection; Salisbury rear axle standard on LWB |
When browsing this collection, use the Model filter to narrow results to Series 2 and 3 fitment. For components where SWB and LWB variants differ, product listings identify the applicable wheelbase.
Parts CategoriesThis collection holds over 2,300 parts across all major categories for Series II, IIA, and Series III vehicles. The categories with the heaviest demand from restoration and maintenance buyers are listed below.
Engine and drivetrain components include gaskets, seals, bearings, timing components, and oil system parts for the 2.25-litre petrol and diesel units. Axle half shafts, differential seals, and swivel housing parts are stocked for both SWB and LWB configurations.
Electrical and wiring components include complete wiring loom kits for Series II, IIA, and III in both SWB and LWB. Left-hand and right-hand drive variants are stocked where available. Connectors, fuses, switches, and earthing hardware are held as individual items.
Body and chassis components include bulkhead sections, floor pans, footwell repair panels, rear crossmembers, door bottoms, sills, and tub panels. These are restoration-critical items for vehicles requiring MOT or RDW structural certification.
Brake system components include brake shoes, wheel cylinders, master cylinders, brake lines, and hardware kits. Correct selection requires confirmation of axle type and wheelbase.
Suspension and steering parts include leaf spring sets for SWB and LWB, shock absorbers, polyurethane bush kits, track rod ends, drag links, and steering box rebuild components.
Clutch and gearbox components include clutch kits, release bearings, and seals for the four-speed main gearbox and two-speed transfer box.
Cooling and fuel system parts, lighting components, interior hardware, and service consumables are stocked across the full generation range.
For component-type browsing across all Land Rover models with model filter support, the following category collections include Series-compatible stock.
Brake shoes, wheel cylinders, master cylinders, brake lines, and hardware kits across the Land Rover range.
Land Rover brake parts →Leaf springs, shock absorbers, bush kits, track rod ends, and steering components for Series and later models.
Land Rover suspension parts →Wiring looms, connectors, switches, fuses, and earthing hardware for all Land Rover generations.
Land Rover electrical parts →Bulkhead sections, floor pans, footwell repair panels, rear crossmembers, sills, and tub panels.
Land Rover chassis and body parts →Every product in this collection is labelled with one of three quality designations: Genuine, OEM, or Aftermarket.
Genuine parts carry the original Land Rover part number and were manufactured by or for Land Rover. For Series II, IIA, and III vehicles, genuine Land Rover stock is limited across most categories due to the age of the range. Where genuine parts are listed, they represent original-specification components.
OEM parts are manufactured to the same specification as the original component, frequently by the same supplier that produced the original part, but sold outside the main brand distribution channel. For mechanical rebuilds on Series vehicles, OEM-specification parts are the standard choice used by workshops across Europe.
Aftermarket parts are independently manufactured to a compatible specification. Quality varies by product and by category. For consumable hardware, body repair panels, and service items on Series vehicles, quality aftermarket parts are the practical choice and are used routinely in professional restorations.
Each product listing identifies its quality tier clearly.
Trade BuyersBudget Parts supplies restoration workshops, fleet operators, and independent garages across the EU. Trade customers running regular Series II or Series III projects can open a trade account for volume pricing, consolidated order options, and correct EU VAT invoicing. For components not currently visible in the catalogue, the sourcing team works with UK and EU supplier networks to locate unlisted parts.
Contact the team with your Commission Number and part requirement.
Technical GuidesThe following guides cover technical background and restoration considerations for Series II, IIA, and Series III vehicles.
Covers the engineering and production history of Series II, IIA, and III, including the key differences between sub-variants, engine fitment across generations, and why certain parts interchange while others do not.
Series 2 and 3 history and engineering →A cross-model diagnostic guide covering fuel system fault finding, relevant to carburetted Series vehicles where starting and fuel delivery issues are a common maintenance challenge.
Land Rover fuel system diagnosis →Covers clutch fault identification across Land Rover models, applicable to the four-speed manual gearbox and clutch assemblies used in Series II, IIA, and Series III.
Land Rover clutch fault diagnosis →Interchangeability within this range is partial and depends on generation, wheelbase, and build date. Engine internals for the 2.25-litre petrol and diesel units carry across Series IIA and Series III in most cases. Certain axle and drivetrain components also share fitment between the two generations. However, body panels, wiring looms, swivel housing components, and some suspension parts differ between generations and between SWB and LWB configurations. A 1980 update to Series III crankshafts and a 1982 update to Series III half shaft splines mean that late Series III axle parts are not always interchangeable with earlier Series III or Series IIA equivalents. Confirm by generation, wheelbase, and build date before ordering.
Series Land Rovers use a Commission Number rather than a modern VIN. This number is stamped on a plate fixed to the bulkhead and encodes the series, engine type, wheelbase, and approximate build date. The Commission Number is the most reliable starting point for confirming which parts apply to your vehicle. The Land Rover Heritage Trust holds production records for the full Series family and can assist with identification on older or incomplete builds. Budget Parts can also confirm fitment from the catalogue if you provide your Commission Number before ordering.
This collection covers all three: Series II (1958 to 1961), Series IIA (1961 to 1971), and Series III (1971 to 1985), in both short wheelbase (88-inch) and long wheelbase (109-inch) configurations. Series I vehicles are not covered here. Series I parts are held in the Land Rover Series 1 Parts collection. If you are unsure which generation your vehicle belongs to, use your Commission Number to confirm before selecting parts.
SWB stands for short wheelbase and LWB for long wheelbase. From Series II onward, the standard wheelbase options were 88 inches (SWB) and 109 inches (LWB). Wheelbase directly affects the fitment of body panels, floor sections, wiring looms, propshaft lengths, and certain suspension and brake components. When ordering, confirming your wheelbase is as important as confirming your generation. Product listings in this collection identify wheelbase applicability where SWB and LWB variants differ.
Yes. This collection includes complete wiring loom kits for Series II, IIA, and Series III in SWB and LWB configurations. Petrol and diesel variants are stocked where applicable, and left-hand and right-hand drive options are held where available. The correct loom for your vehicle depends on your generation, wheelbase, drive side, and engine type. Confirming these details before ordering, or contacting Budget Parts with your Commission Number, is the most reliable way to select the correct kit.
This collection stocks a range of body and chassis repair panels for Series II, IIA, and Series III vehicles. Available items include bulkhead sections, footwell repair kits, floor pans, rear crossmembers, door bottom repair sections, and sill panels. These panels are relevant for vehicles requiring structural certification under MOT or RDW inspection. Correct panel selection depends on your wheelbase and, in some cases, your build year within the Series III production run. If you are unsure, contact Budget Parts with your Commission Number before ordering.
Yes. Budget Parts is based in The Hague, Netherlands, and ships to customers across the EU and beyond. EU customers receive invoices with correct VAT treatment. Trade customers and workshops with regular requirements can open a trade account for volume pricing and consolidated ordering. For parts not currently listed in the catalogue, the sourcing team can locate components through UK and EU supplier networks.