for Discounts / VAT
for Discounts & Correct VAT
Parts for Land Rover Series II, Series IIA, and Series III (1958 to 1985), covering 88-inch short wheelbase and 109-inch long wheelbase configurations. Genuine, OEM, and aftermarket options across engine, body, electrical, suspension, and brake categories. Stocked and shipped from The Hague as part of the full Land Rover Series parts catalogue.
What fits: Series II (1958 to 1961), Series IIA (1961 to 1971), Series III (1971 to 1985), SWB and LWB.
switch loss vacuum
Driving Member is the front hub drive flange that couples the axle halfshaft to the road wheel hub. It bolts to the outer face of the front hub, w...
View full detailsDiesel Injector for the fuel injection system, delivering metered, atomised fuel from the injection pump into the engine. Fitted to the 2.25L and ...
View full detailsManifold Clamp - a clamping plate that secures the manifold to the cylinder head. It fits over the manifold flange and draws down onto the cylinde...
View full detailsDistance Piece is the spacer fitted to the front halfshaft within the front axle and hub assembly. It sets the correct positioning of the halfshaf...
View full detailsClevis Pin for the clutch cross shaft, part of the mechanical clutch release linkage. The pin forms the pivoting joint that connects the clutch op...
View full detailslock washer. sold EACH.
Door Seal The lower rear door seal for the left-hand front door, sealing the lower rear edge of the door against the body. It forms part of the fr...
View full detailsLeather hasp civilian
Rear Quarter Seal - the rubber glazing seal that secures the fixed rear quarter window into the hard-top body aperture. Sized for 5mm glass, it be...
View full detailsTailgate Seal for the lower edge of the rear tailboard. It seats along the bottom of the drop-down tailgate and seals against the body, keeping wa...
View full detailsMain Switch: heavy-duty main switch rated at 1000 A.
Banjo Bolt
Swivel Bearing - the bearing on which the front axle swivel pin housing pivots, within the steering swivel assembly. It locates the swivel pin in ...
View full detailsValve Stem Seal - the seal fitted over the valve stem in the cylinder head to control the oil that passes down the stem into the port. This is the...
View full detailsBreather and oil filler cap for the rocker cover, part of the engine crankcase ventilation system on the 2.25L and 2.5L 4-cylinder petrol and natur...
View full detailsExhaust Valve for the cylinder head of the 2.25L 4-cylinder petrol engine, with a 35mm head diameter and a single collet groove on the stem. It se...
View full detailsRadiator Muff for Series 2A (late models with headlights in the wings) and Series 3 Land Rovers, with black-edged trim. This muff fits across the ...
View full detailsDoor Top Glazing Kit supplies the fixings and retaining components used to secure the glass within a door top frame. Fitted when glazing or re-gla...
View full detailsSeat belt bracket RH
Silencer Exhaust 2.6
Door Latch Assembly - LH - Front - Non-Locking for Land Rover Series vehicles from 1958 to 1984. This left-hand front door latch assembly fits the...
View full detailsHandbrake Drum is the drum for the transmission-mounted parking brake, for use with the LT76 gearbox. Mounted at the rear of the gearbox on the tr...
View full detailsExhaust Connecting Pipe is the intermediate section of the exhaust system for Series short wheelbase vehicles fitted with the 2.25L diesel engine, ...
View full detailsBrake Master Cylinder Repair Kit - Dual Line for the tandem brake master cylinder of the dual-line braking system. The kit supplies the replacemen...
View full detailsGearbox Gasket for the LT76 four-speed gearbox with integral transfer assembly. It seals a mating housing face within the gearbox and transfer cas...
View full detailsInlet Valve for the 2.25L and 2.5L four-cylinder diesel engines, including the 2.5L Turbo Diesel, operating in the cylinder head valve train. It o...
View full detailsShackle plate
Handbrake Expander operates the transmission-mounted drum handbrake, forcing the brake shoes apart against the drum when the handbrake is applied. ...
View full detailsOuter Distance Piece for the front axle swivel pin housing. The distance piece is a spacer that sets the position of the swivel pin bearing within...
View full detailsTrack Rod End Boot Ring - spring retaining ring for the track rod end of the steering linkage. It clamps the rubber dust boot onto the track rod en...
View full detailsClutch Plate is the friction-lined driven plate of the clutch assembly, 9 inch (229 mm) diameter. Its splined hub engages the gearbox input shaft ...
View full detailsDomed Nut with a 5/16 UNF thread, a finishing fastener. The domed (acorn) form encloses the end of the stud or bolt it threads onto, protecting th...
View full detailsPiston Ring Set - Standard - 2.25/2.5 Diesel
Rotor Arm - Ducellier Type for the ignition distributor assembly. This rotor arm fits the Ducellier-type distributor and rotates inside the distri...
View full detailsBrake Hose is a flexible hydraulic line in the braking circuit, carrying fluid from the rigid chassis-mounted brake pipe to the caliper or wheel cy...
View full detailsSteering Drag Link - With Bracket - 73cm is a steering linkage rod, supplied with an integrated steering damper bracket. The drag link transmits s...
View full detailsGrommet & Gaiter Kit for the transmission tunnel controls, sealing the apertures where the levers pass through the floor. The kit contains the...
View full detailsPiston Ring Set supplies the sealing rings for one piston of the 3.5L V8 petrol engine, in standard (non-oversize) bore size. The rings seal the p...
View full detailsBonnet Frame Top Hat Supports are top-hat section reinforcement pieces that weld to the underside of the bonnet frame, stiffening the outer bonnet ...
View full detailsMaster Cylinder Reservoir Cap seals the fluid reservoir on the brake or clutch master cylinder. It screws or presses onto the reservoir neck to re...
View full detailsSump Gasket seals the joint between the oil sump and the cylinder block within the engine lubrication system, preventing oil leakage at the sump fl...
View full detailsRocker Arm for the rocker shaft valvetrain assembly of the Rover V8 petrol engine. The rocker arm pivots on the rocker shaft and transmits the lif...
View full detailsWheel Nut A single-chamfer wheel nut that secures the road wheel to the hub studs. The chamfered seating face centres and clamps the wheel against...
View full detailsAccelerator Cable in the throttle control linkage, connecting the accelerator pedal to the carburettor throttle spindle. Transmits pedal movement ...
View full detailsLock Washer for the carburettor butterfly spindle. This lock washer secures the retaining nut on the throttle butterfly spindle inside the carbure...
View full detailsShock Absorber Bush Set for the shock absorber mountings. This set provides the bushes that locate each shock absorber at its mounting eyes, insul...
View full detailsCubby Box Hinge in brass, forming the pivot point for the centre console cubby box lid. The hinge fixes the lid to the cubby box body, carrying th...
View full detailsParts for Land Rover Series II, Series IIA, and Series III, produced from 1958 to 1985. Covers short wheelbase (88-inch) and long wheelbase (109-inch) configurations. Series I is a separate collection. Use your Commission Number to confirm fitment before ordering.
This collection covers Land Rover Series II (1958 to 1961), Series IIA (1961 to 1971), and Series III (1971 to 1985) in both short wheelbase and long wheelbase configurations. It does not cover Series I vehicles. Series I parts are held in a separate collection.
The three generations in this collection share the same core body-on-frame ladder chassis, a two-speed transfer gearbox, and a four-speed manual main gearbox. Wheelbase options from Series II onward were 88 inches (short wheelbase, referred to as SWB) and 109 inches (long wheelbase, referred to as LWB). Parts compatibility is not uniform across the three generations, and wheelbase is a fitment variable for a significant number of components including body panels, wiring looms, propshafts, and floor sections.
The 2.25-litre petrol and diesel engines are shared across Series IIA and Series III, and engine internals for these units carry across both generations in most cases. Other components, including wiring configurations, swivel housing seals, and certain axle parts, differ between generations and between sub-variants within the Series III production run. A 1980 update introduced five main bearing crankshafts to the 2.25-litre engines. A 1982 update increased the Series III half shaft drive spline count from 10 to 24, which affects axle half shaft selection for late Series III vehicles.
LWB Series IIA models were available with a 2.6-litre straight-six petrol engine. Series III LWB models used the Salisbury rear axle as standard. The Stage 1 V8 variant, produced from 1979 to 1985, used a 3.5-litre Rover V8 and the LT95 gearbox; this was an LWB-only production variant with some component differences from standard Series III specification.
The Land Rover UK heritage pages cover the original design and production history of the Series family and are a useful background reference for owners identifying their vehicle's generation and specification.
Series Land Rovers do not carry a modern 17-digit VIN. Instead, each vehicle has a Commission Number stamped on a plate fixed to the bulkhead. This number encodes the series, engine type, wheelbase, and approximate build date. Confirming your Commission Number before ordering is the most reliable way to ensure parts match your specific vehicle.
The Land Rover Heritage Trust holds production records and Commission Number data for the full Series family and is the definitive reference for vehicle identification on older or incomplete builds.
If you are uncertain about your generation or wheelbase, contact Budget Parts with your Commission Number before placing an order. The team will confirm applicable fitment from the catalogue.
Fitment NotesParts compatibility across this collection varies by generation, wheelbase, and in some cases by build date within a generation. The table below summarises the key fitment variables.
| Generation | Production | Wheelbase options | Engines | Key fitment notes |
|---|---|---|---|---|
| Series II | 1958 to 1961 | 88-inch SWB, 109-inch LWB | 2.0-litre petrol (early), 2.25-litre petrol, 2.0-litre diesel | Some early SWB models used the Series I 2.0-litre engine |
| Series IIA | 1961 to 1971 | 88-inch SWB, 109-inch LWB | 2.25-litre petrol, 2.25-litre diesel, 2.6-litre I6 (LWB only) | Highest-volume sub-series; many mechanical parts cross to early Series III |
| Series III | 1971 to 1985 | 88-inch SWB, 109-inch LWB | 2.25-litre petrol, 2.25-litre diesel, 2.6-litre I6, 3.5-litre V8 petrol | Stage 1 V8 was LWB only (1979 to 1985); 1980 crank update and 1982 half shaft spline update affect part selection; Salisbury rear axle standard on LWB |
When browsing this collection, use the Model filter to narrow results to Series 2 and 3 fitment. For components where SWB and LWB variants differ, product listings identify the applicable wheelbase.
Parts CategoriesThis collection holds over 2,300 parts across all major categories for Series II, IIA, and Series III vehicles. The categories with the heaviest demand from restoration and maintenance buyers are listed below.
Engine and drivetrain components include gaskets, seals, bearings, timing components, and oil system parts for the 2.25-litre petrol and diesel units. Axle half shafts, differential seals, and swivel housing parts are stocked for both SWB and LWB configurations.
Electrical and wiring components include complete wiring loom kits for Series II, IIA, and III in both SWB and LWB. Left-hand and right-hand drive variants are stocked where available. Connectors, fuses, switches, and earthing hardware are held as individual items.
Body and chassis components include bulkhead sections, floor pans, footwell repair panels, rear crossmembers, door bottoms, sills, and tub panels. These are restoration-critical items for vehicles requiring MOT or RDW structural certification.
Brake system components include brake shoes, wheel cylinders, master cylinders, brake lines, and hardware kits. Correct selection requires confirmation of axle type and wheelbase.
Suspension and steering parts include leaf spring sets for SWB and LWB, shock absorbers, polyurethane bush kits, track rod ends, drag links, and steering box rebuild components.
Clutch and gearbox components include clutch kits, release bearings, and seals for the four-speed main gearbox and two-speed transfer box.
Cooling and fuel system parts, lighting components, interior hardware, and service consumables are stocked across the full generation range.
For component-type browsing across all Land Rover models with model filter support, the following category collections include Series-compatible stock.
Brake shoes, wheel cylinders, master cylinders, brake lines, and hardware kits across the Land Rover range.
Land Rover brake parts →Leaf springs, shock absorbers, bush kits, track rod ends, and steering components for Series and later models.
Land Rover suspension parts →Wiring looms, connectors, switches, fuses, and earthing hardware for all Land Rover generations.
Land Rover electrical parts →Bulkhead sections, floor pans, footwell repair panels, rear crossmembers, sills, and tub panels.
Land Rover chassis and body parts →Every product in this collection is labelled with one of three quality designations: Genuine, OEM, or Aftermarket.
Genuine parts carry the original Land Rover part number and were manufactured by or for Land Rover. For Series II, IIA, and III vehicles, genuine Land Rover stock is limited across most categories due to the age of the range. Where genuine parts are listed, they represent original-specification components.
OEM parts are manufactured to the same specification as the original component, frequently by the same supplier that produced the original part, but sold outside the main brand distribution channel. For mechanical rebuilds on Series vehicles, OEM-specification parts are the standard choice used by workshops across Europe.
Aftermarket parts are independently manufactured to a compatible specification. Quality varies by product and by category. For consumable hardware, body repair panels, and service items on Series vehicles, quality aftermarket parts are the practical choice and are used routinely in professional restorations.
Each product listing identifies its quality tier clearly.
Trade BuyersBudget Parts supplies restoration workshops, fleet operators, and independent garages across the EU. Trade customers running regular Series II or Series III projects can open a trade account for volume pricing, consolidated order options, and correct EU VAT invoicing. For components not currently visible in the catalogue, the sourcing team works with UK and EU supplier networks to locate unlisted parts.
Contact the team with your Commission Number and part requirement.
Technical GuidesThe following guides cover technical background and restoration considerations for Series II, IIA, and Series III vehicles.
Covers the engineering and production history of Series II, IIA, and III, including the key differences between sub-variants, engine fitment across generations, and why certain parts interchange while others do not.
Series 2 and 3 history and engineering →A cross-model diagnostic guide covering fuel system fault finding, relevant to carburetted Series vehicles where starting and fuel delivery issues are a common maintenance challenge.
Land Rover fuel system diagnosis →Covers clutch fault identification across Land Rover models, applicable to the four-speed manual gearbox and clutch assemblies used in Series II, IIA, and Series III.
Land Rover clutch fault diagnosis →Interchangeability within this range is partial and depends on generation, wheelbase, and build date. Engine internals for the 2.25-litre petrol and diesel units carry across Series IIA and Series III in most cases. Certain axle and drivetrain components also share fitment between the two generations. However, body panels, wiring looms, swivel housing components, and some suspension parts differ between generations and between SWB and LWB configurations. A 1980 update to Series III crankshafts and a 1982 update to Series III half shaft splines mean that late Series III axle parts are not always interchangeable with earlier Series III or Series IIA equivalents. Confirm by generation, wheelbase, and build date before ordering.
Series Land Rovers use a Commission Number rather than a modern VIN. This number is stamped on a plate fixed to the bulkhead and encodes the series, engine type, wheelbase, and approximate build date. The Commission Number is the most reliable starting point for confirming which parts apply to your vehicle. The Land Rover Heritage Trust holds production records for the full Series family and can assist with identification on older or incomplete builds. Budget Parts can also confirm fitment from the catalogue if you provide your Commission Number before ordering.
This collection covers all three: Series II (1958 to 1961), Series IIA (1961 to 1971), and Series III (1971 to 1985), in both short wheelbase (88-inch) and long wheelbase (109-inch) configurations. Series I vehicles are not covered here. Series I parts are held in the Land Rover Series 1 Parts collection. If you are unsure which generation your vehicle belongs to, use your Commission Number to confirm before selecting parts.
SWB stands for short wheelbase and LWB for long wheelbase. From Series II onward, the standard wheelbase options were 88 inches (SWB) and 109 inches (LWB). Wheelbase directly affects the fitment of body panels, floor sections, wiring looms, propshaft lengths, and certain suspension and brake components. When ordering, confirming your wheelbase is as important as confirming your generation. Product listings in this collection identify wheelbase applicability where SWB and LWB variants differ.
Yes. This collection includes complete wiring loom kits for Series II, IIA, and Series III in SWB and LWB configurations. Petrol and diesel variants are stocked where applicable, and left-hand and right-hand drive options are held where available. The correct loom for your vehicle depends on your generation, wheelbase, drive side, and engine type. Confirming these details before ordering, or contacting Budget Parts with your Commission Number, is the most reliable way to select the correct kit.
This collection stocks a range of body and chassis repair panels for Series II, IIA, and Series III vehicles. Available items include bulkhead sections, footwell repair kits, floor pans, rear crossmembers, door bottom repair sections, and sill panels. These panels are relevant for vehicles requiring structural certification under MOT or RDW inspection. Correct panel selection depends on your wheelbase and, in some cases, your build year within the Series III production run. If you are unsure, contact Budget Parts with your Commission Number before ordering.
Yes. Budget Parts is based in The Hague, Netherlands, and ships to customers across the EU and beyond. EU customers receive invoices with correct VAT treatment. Trade customers and workshops with regular requirements can open a trade account for volume pricing and consolidated ordering. For parts not currently listed in the catalogue, the sourcing team can locate components through UK and EU supplier networks.