for Discounts / VAT
for Discounts & Correct VAT
Parts for Land Rover Series II, Series IIA, and Series III (1958 to 1985), covering 88-inch short wheelbase and 109-inch long wheelbase configurations. Genuine, OEM, and aftermarket options across engine, body, electrical, suspension, and brake categories. Stocked and shipped from The Hague as part of the full Land Rover Series parts catalogue.
What fits: Series II (1958 to 1961), Series IIA (1961 to 1971), Series III (1971 to 1985), SWB and LWB.
Front Door Hinge Kit for renewing the front door hinges. The kit includes 4 zinc-plated hinges with Torx head bolts and all fixings.
Battery Cover - the protective cover fitted over the battery in the engine bay. It shields the battery casing and terminals from debris and accide...
View full detailsDynamo Brush Set for the Lucas C40 dynamo. The carbon brushes bear against the commutator to conduct current through the rotating armature windings...
View full detailsCarburettor Float for the Zenith 361V carburettor, part of the Fuel System assembly on Series petrol engines. The float rides on the fuel surface ...
View full detailsClutch Withdrawal Tube fitted in the clutch cross-shaft withdrawal mechanism on Series II, IIA, and III Land Rovers. This tube forms the connectin...
View full detailsDistributor Cap for the 2.6L 6-cylinder petrol ignition system on the Land Rover Series III. Fitted over the distributor body, the cap receives hi...
View full detailsWiper Gear Linkage for the windscreen wiper system, transmitting drive from the wiper motor to the wheelbox and wiper spindle. It converts the rot...
View full detailsStarter Motor for the 2.25L 4-cylinder diesel engine, operating in the engine starting circuit. When energised through the starter solenoid, the p...
View full detailsSeat Box End Panel - Right-Hand is a repair panel forming the outer end face of the seat box assembly. It replaces the corroded offside end panel ...
View full detailsCirclip - Gear Lever Spring Retention for the Series Land Rover gearbox gear lever assembly. This circlip retains the spring, retaining plate and ...
View full detailsthrust collar, bush for stub axle - RRclassic upto (VIN) HA610293, - 101" Forward Control.
Ignition and Starter Switch - the electrical switch unit that mounts to the base of the steering column lock, in the ignition and starting circuit,...
View full detailsRear Sill Panel - Left Hand is a pressed steel body panel that forms the lower left-hand side of the rear body tub. The panel closes the gap betwe...
View full detailsGasket kit carburettor Zenith Stromberg 175CD
Gearbox Side Cover Gasket for the LT95 4-speed V8 gearbox. This gasket seals the side cover to the gearbox casing, preventing oil leaks from the ge...
View full detailsGearbox Cover Plate Gasket for the LT76 gearbox. This rubber gasket seals the cover plate to the gearbox casing, sealing the joint against oil lea...
View full detailsTappet Slide for Land Rover 4-cylinder engines, covering the Series I, Series II, Series IIA, and Series III (2.0L Diesel and 2.25L Petrol and Dies...
View full detailsShock Absorber - Oil Filled - Front for the front suspension assembly on Series I, II, and IIA Land Rovers. This oil-filled hydraulic unit mounts ...
View full detailsGearbox Tie Rod Buffer for the gearbox steady (tie rod) mounting. The tie rod restrains the gearbox against fore-and-aft movement under load. This...
View full detailsstriker lock LH for "anti-burst" locks. (lift-up type)
Pan Head Screw - a machine screw with a low, rounded-top head and a flat bearing face, used as a general-purpose fixing. Metric M5 thread with a 1...
View full detailsElectronic Distributor for the ignition system of the 4-cylinder petrol engine. It distributes high-tension voltage from the ignition coil to each...
View full detailsRubber Washer - Window Catch for the sliding window catch assembly on Series II, IIA, and III Station Wagon body variants, produced up to 1984. Th...
View full detailsBody Mounting Shim used to set the correct clearance and alignment between the body tub and the chassis mounting points. This thin flat shim is us...
View full detailsExhaust Packing Plate for the exhaust mounting strap assembly. It sits between the exhaust strap and its chassis bracket, packing the joint so the...
View full detailsPlain Washer distributes the clamping load of a bolt or nut across the mounting surface and protects the surface as the fastener is tightened. Siz...
View full detailsSpring Washer for the fuel tank sender unit and fuel pick-up pipe fixings. Fitted beneath the retaining screws that secure the fuel gauge sender u...
View full detailsFiller Strip for the door top. The strip fits along the top edge of the door, closing and finishing the joint at the door-top glass frame and seal...
View full detailsBolt - 5/16 inch BSF x 1 inch for the gearbox selector assembly. Used to secure the gear selector forks to their respective selector shafts within...
View full detailsFlanged Bolt - an M6 x 25mm hexagon-head bolt with an integral flange formed beneath the head. The flange provides a wide bearing face that spread...
View full detailsFront Floorplate - Left-Hand Side for the cab floor structure of Series II, IIA, and III Land Rovers. This pressed steel panel forms the left-hand...
View full detailsFront Floorplate - Right-Hand Side for the cab floor structure of Series II, IIA, and III Land Rovers. This pressed steel panel forms the right-ha...
View full detailsRear Spring Hanger is a chassis mounting bracket in the rear leaf-spring suspension, forming the forward anchor point that carries the front eye of...
View full detailsInterior Lamp - courtesy lamp for the passenger compartment. Provides interior illumination as part of the interior lighting circuit, typically sw...
View full detailsMainshaft Peg is a locating peg fitted to the mainshaft of the LT67 gearbox. It positions and retains its associated component on the gearbox main...
View full detailsHex nut
Distance sleeve mainshaft
Gasket
Crankshaft Oil Seal - Rear seals the rear of the crankshaft where it leaves the cylinder block at the flywheel end, retaining oil within the bottom...
View full detailsMirror Head is a large replacement exterior door-mirror head measuring 265mm x 160mm, offering an increased field of view over the standard head. ...
View full detailsFootwell Repair Panel is a welded body repair panel for the right-hand (nearside) footwell, replacing the corroded or damaged footwell section ahea...
View full detailsMainshaft peg
Differential Bearing for the Salisbury axle. It is one of the pair of taper roller bearings that carry the differential carrier - the housing holdi...
View full detailsTrunnion
Exhaust Valve Guide is pressed into the cylinder head and supports the exhaust valve stem, keeping it accurately centred as the valve opens and clo...
View full detailsFuel Filler Breather Hose, part of the fuel filler and tank ventilation system. The hose vents air displaced from the fuel tank during refuelling,...
View full detailsTappet kit
Gasket
Parts for Land Rover Series II, Series IIA, and Series III, produced from 1958 to 1985. Covers short wheelbase (88-inch) and long wheelbase (109-inch) configurations. Series I is a separate collection. Use your Commission Number to confirm fitment before ordering.
This collection covers Land Rover Series II (1958 to 1961), Series IIA (1961 to 1971), and Series III (1971 to 1985) in both short wheelbase and long wheelbase configurations. It does not cover Series I vehicles. Series I parts are held in a separate collection.
The three generations in this collection share the same core body-on-frame ladder chassis, a two-speed transfer gearbox, and a four-speed manual main gearbox. Wheelbase options from Series II onward were 88 inches (short wheelbase, referred to as SWB) and 109 inches (long wheelbase, referred to as LWB). Parts compatibility is not uniform across the three generations, and wheelbase is a fitment variable for a significant number of components including body panels, wiring looms, propshafts, and floor sections.
The 2.25-litre petrol and diesel engines are shared across Series IIA and Series III, and engine internals for these units carry across both generations in most cases. Other components, including wiring configurations, swivel housing seals, and certain axle parts, differ between generations and between sub-variants within the Series III production run. A 1980 update introduced five main bearing crankshafts to the 2.25-litre engines. A 1982 update increased the Series III half shaft drive spline count from 10 to 24, which affects axle half shaft selection for late Series III vehicles.
LWB Series IIA models were available with a 2.6-litre straight-six petrol engine. Series III LWB models used the Salisbury rear axle as standard. The Stage 1 V8 variant, produced from 1979 to 1985, used a 3.5-litre Rover V8 and the LT95 gearbox; this was an LWB-only production variant with some component differences from standard Series III specification.
The Land Rover UK heritage pages cover the original design and production history of the Series family and are a useful background reference for owners identifying their vehicle's generation and specification.
Series Land Rovers do not carry a modern 17-digit VIN. Instead, each vehicle has a Commission Number stamped on a plate fixed to the bulkhead. This number encodes the series, engine type, wheelbase, and approximate build date. Confirming your Commission Number before ordering is the most reliable way to ensure parts match your specific vehicle.
The Land Rover Heritage Trust holds production records and Commission Number data for the full Series family and is the definitive reference for vehicle identification on older or incomplete builds.
If you are uncertain about your generation or wheelbase, contact Budget Parts with your Commission Number before placing an order. The team will confirm applicable fitment from the catalogue.
Fitment NotesParts compatibility across this collection varies by generation, wheelbase, and in some cases by build date within a generation. The table below summarises the key fitment variables.
| Generation | Production | Wheelbase options | Engines | Key fitment notes |
|---|---|---|---|---|
| Series II | 1958 to 1961 | 88-inch SWB, 109-inch LWB | 2.0-litre petrol (early), 2.25-litre petrol, 2.0-litre diesel | Some early SWB models used the Series I 2.0-litre engine |
| Series IIA | 1961 to 1971 | 88-inch SWB, 109-inch LWB | 2.25-litre petrol, 2.25-litre diesel, 2.6-litre I6 (LWB only) | Highest-volume sub-series; many mechanical parts cross to early Series III |
| Series III | 1971 to 1985 | 88-inch SWB, 109-inch LWB | 2.25-litre petrol, 2.25-litre diesel, 2.6-litre I6, 3.5-litre V8 petrol | Stage 1 V8 was LWB only (1979 to 1985); 1980 crank update and 1982 half shaft spline update affect part selection; Salisbury rear axle standard on LWB |
When browsing this collection, use the Model filter to narrow results to Series 2 and 3 fitment. For components where SWB and LWB variants differ, product listings identify the applicable wheelbase.
Parts CategoriesThis collection holds over 2,300 parts across all major categories for Series II, IIA, and Series III vehicles. The categories with the heaviest demand from restoration and maintenance buyers are listed below.
Engine and drivetrain components include gaskets, seals, bearings, timing components, and oil system parts for the 2.25-litre petrol and diesel units. Axle half shafts, differential seals, and swivel housing parts are stocked for both SWB and LWB configurations.
Electrical and wiring components include complete wiring loom kits for Series II, IIA, and III in both SWB and LWB. Left-hand and right-hand drive variants are stocked where available. Connectors, fuses, switches, and earthing hardware are held as individual items.
Body and chassis components include bulkhead sections, floor pans, footwell repair panels, rear crossmembers, door bottoms, sills, and tub panels. These are restoration-critical items for vehicles requiring MOT or RDW structural certification.
Brake system components include brake shoes, wheel cylinders, master cylinders, brake lines, and hardware kits. Correct selection requires confirmation of axle type and wheelbase.
Suspension and steering parts include leaf spring sets for SWB and LWB, shock absorbers, polyurethane bush kits, track rod ends, drag links, and steering box rebuild components.
Clutch and gearbox components include clutch kits, release bearings, and seals for the four-speed main gearbox and two-speed transfer box.
Cooling and fuel system parts, lighting components, interior hardware, and service consumables are stocked across the full generation range.
For component-type browsing across all Land Rover models with model filter support, the following category collections include Series-compatible stock.
Brake shoes, wheel cylinders, master cylinders, brake lines, and hardware kits across the Land Rover range.
Land Rover brake parts →Leaf springs, shock absorbers, bush kits, track rod ends, and steering components for Series and later models.
Land Rover suspension parts →Wiring looms, connectors, switches, fuses, and earthing hardware for all Land Rover generations.
Land Rover electrical parts →Bulkhead sections, floor pans, footwell repair panels, rear crossmembers, sills, and tub panels.
Land Rover chassis and body parts →Every product in this collection is labelled with one of three quality designations: Genuine, OEM, or Aftermarket.
Genuine parts carry the original Land Rover part number and were manufactured by or for Land Rover. For Series II, IIA, and III vehicles, genuine Land Rover stock is limited across most categories due to the age of the range. Where genuine parts are listed, they represent original-specification components.
OEM parts are manufactured to the same specification as the original component, frequently by the same supplier that produced the original part, but sold outside the main brand distribution channel. For mechanical rebuilds on Series vehicles, OEM-specification parts are the standard choice used by workshops across Europe.
Aftermarket parts are independently manufactured to a compatible specification. Quality varies by product and by category. For consumable hardware, body repair panels, and service items on Series vehicles, quality aftermarket parts are the practical choice and are used routinely in professional restorations.
Each product listing identifies its quality tier clearly.
Trade BuyersBudget Parts supplies restoration workshops, fleet operators, and independent garages across the EU. Trade customers running regular Series II or Series III projects can open a trade account for volume pricing, consolidated order options, and correct EU VAT invoicing. For components not currently visible in the catalogue, the sourcing team works with UK and EU supplier networks to locate unlisted parts.
Contact the team with your Commission Number and part requirement.
Technical GuidesThe following guides cover technical background and restoration considerations for Series II, IIA, and Series III vehicles.
Covers the engineering and production history of Series II, IIA, and III, including the key differences between sub-variants, engine fitment across generations, and why certain parts interchange while others do not.
Series 2 and 3 history and engineering →A cross-model diagnostic guide covering fuel system fault finding, relevant to carburetted Series vehicles where starting and fuel delivery issues are a common maintenance challenge.
Land Rover fuel system diagnosis →Covers clutch fault identification across Land Rover models, applicable to the four-speed manual gearbox and clutch assemblies used in Series II, IIA, and Series III.
Land Rover clutch fault diagnosis →Interchangeability within this range is partial and depends on generation, wheelbase, and build date. Engine internals for the 2.25-litre petrol and diesel units carry across Series IIA and Series III in most cases. Certain axle and drivetrain components also share fitment between the two generations. However, body panels, wiring looms, swivel housing components, and some suspension parts differ between generations and between SWB and LWB configurations. A 1980 update to Series III crankshafts and a 1982 update to Series III half shaft splines mean that late Series III axle parts are not always interchangeable with earlier Series III or Series IIA equivalents. Confirm by generation, wheelbase, and build date before ordering.
Series Land Rovers use a Commission Number rather than a modern VIN. This number is stamped on a plate fixed to the bulkhead and encodes the series, engine type, wheelbase, and approximate build date. The Commission Number is the most reliable starting point for confirming which parts apply to your vehicle. The Land Rover Heritage Trust holds production records for the full Series family and can assist with identification on older or incomplete builds. Budget Parts can also confirm fitment from the catalogue if you provide your Commission Number before ordering.
This collection covers all three: Series II (1958 to 1961), Series IIA (1961 to 1971), and Series III (1971 to 1985), in both short wheelbase (88-inch) and long wheelbase (109-inch) configurations. Series I vehicles are not covered here. Series I parts are held in the Land Rover Series 1 Parts collection. If you are unsure which generation your vehicle belongs to, use your Commission Number to confirm before selecting parts.
SWB stands for short wheelbase and LWB for long wheelbase. From Series II onward, the standard wheelbase options were 88 inches (SWB) and 109 inches (LWB). Wheelbase directly affects the fitment of body panels, floor sections, wiring looms, propshaft lengths, and certain suspension and brake components. When ordering, confirming your wheelbase is as important as confirming your generation. Product listings in this collection identify wheelbase applicability where SWB and LWB variants differ.
Yes. This collection includes complete wiring loom kits for Series II, IIA, and Series III in SWB and LWB configurations. Petrol and diesel variants are stocked where applicable, and left-hand and right-hand drive options are held where available. The correct loom for your vehicle depends on your generation, wheelbase, drive side, and engine type. Confirming these details before ordering, or contacting Budget Parts with your Commission Number, is the most reliable way to select the correct kit.
This collection stocks a range of body and chassis repair panels for Series II, IIA, and Series III vehicles. Available items include bulkhead sections, footwell repair kits, floor pans, rear crossmembers, door bottom repair sections, and sill panels. These panels are relevant for vehicles requiring structural certification under MOT or RDW inspection. Correct panel selection depends on your wheelbase and, in some cases, your build year within the Series III production run. If you are unsure, contact Budget Parts with your Commission Number before ordering.
Yes. Budget Parts is based in The Hague, Netherlands, and ships to customers across the EU and beyond. EU customers receive invoices with correct VAT treatment. Trade customers and workshops with regular requirements can open a trade account for volume pricing and consolidated ordering. For parts not currently listed in the catalogue, the sourcing team can locate components through UK and EU supplier networks.