Land Rover Series 2 & 3 Parts

Driving Member Bolt for the axle driving member assembly. This 3/8" BSF x 1-19/32" bolt retains the driving member to the hub assembly. The drivin...

Drum Brake Shoe Set covering one full axle. The shoes carry the friction linings that press outward against the brake drum to slow the wheel when t...

Brake Master Cylinder - LWB - To 1980

Air Intake Hose for the 2.25L and 2.6L petrol induction system. This flexible rubber hose connects the air filter housing to the carburettor intak...

Copper Injector Sealing Washer in the fuel injection assembly of pre-TDi Land Rover diesel engines. This copper washer seats beneath the injector ...

Windscreen Washer Pump, 12V electric, for the windscreen washer system. The pump draws screen-wash fluid from the washer reservoir and delivers it ...

Fuel Tank Spill Return Pipe Gasket for the fuel tank assembly. This gasket seals the joint where the spill return pipe meets the fuel tank, preven...

Front left-hand wheel cylinder for the hydraulic front braking system, installed within the brake backplate assembly of 11-inch front brake configu...

Oil Seal - a radial oil seal fitted between the wheel hub and stub axle within the wheel hub and drive shaft assembly. The seal retains lubricant ...

Crankshaft Rear Oil Seal Kit - Cork for the rear crankshaft sealing assembly on Series Land Rover engines with a 3-bearing crankshaft. This kit su...

Clutch Hose - flexible hydraulic line in the clutch actuation circuit. Carries hydraulic fluid from the rigid pipe run to the clutch slave cylinde...

Differential Carrier Gasket for the Rover-type axle assembly. The gasket seals the differential carrier housing against the axle casing at the cen...

Zenith Carburettor Overhaul Kit for the Zenith 36IV carburettor on 4-cylinder petrol engines. This is the complete overhaul kit for the Zenith 36I...

Carburettor Manifold Gasket for the 2.25L petrol and carburettor-equipped Defender engines. This gasket seals at the interface between the carbure...

Wheel Cylinder for the drum brake assembly - the right-hand hydraulic slave cylinder that operates the brake shoes. The same cylinder serves either...

Fuel Sender Unit Gasket for the fuel gauge sender unit fitted to the fuel tank. This gasket seals the joint between the sender unit flange and the...

Transmission Brake Dust Cover for the central handbrake drum on the transmission output shaft. This cover shields the handbrake drum and brake sho...

Brake Shoe Set for the front drum brake assembly, supplied as a complete axle set of four shoes covering both front wheels. Each shoe carries the ...

Exhaust Gasket sealing the exhaust manifold-to-downpipe flange on Series Land Rover 4-cylinder petrol and diesel engines. This four-hole flange ga...

Worm-drive Hose Clip with a 32-50 mm clamping range, used to secure a flexible hose to a rigid pipe stub or spigot. Tightening the worm screw draws...

Spire Clip used to retain front wing panels and heater assembly components. This spring-steel clip slides over a screw or stud thread and grips se...

Upgrade your Series Land Rover suspension with this Polyurethane Shock Absorber Bush Set in black. The set includes 4 pieces, providing everything ...

Front brake wheel cylinder designed for use on Land Rover Series I, Series II, and Series III models. This component forms part of the hydraulic dr...

Spring Bush for the leaf spring suspension system on Series Land Rovers. This rubber bush fits into the spring eye at the front fixed mount and re...

Brake Shoe Spring for drum brake assemblies. This return spring draws the brake shoes away from the drum surface when the brake pedal is released,...

Low Note Horn, a 335 Hz electric horn within the audible warning circuit. Produces the low-frequency tone of a dual-tone horn arrangement, pairing...

Radiator - Copper Core sits in the engine cooling circuit, dissipating heat from the coolant to hold a stable operating temperature under load. Th...

Transfer Box Sump Gasket for the LT76 combined gearbox and transfer box unit used in Series Land Rovers. This flat sealing washer seals the transf...

Inlet Manifold Gasket - Diesel for the 2.25L and 2.5L 4-Cylinder diesel engine. Fitted between the inlet manifold and the cylinder head, this gask...

Rear Stop/Tail Lamp - combined rear stop and tail lamp, supplied as a complete lens and body assembly. It mounts in the rear lamp position and pro...

Rubber Sealing Ring for gear selector shafts in the LT76 gearbox and LT95 transfer box. In the LT76 gearbox, two rings are fitted per unit, sealin...

Pipe clutch down

Track Rod End for the steering linkage, with a left-hand thread and a fully threaded shank. The track rod end forms the ball-jointed connection be...

Distributor Cap for the ignition distributor on the V8 EFI engine. The cap seats over the distributor and carries the high-tension current from th...

Exhaust Manifold Gasket for the 3.5L V8 petrol engine. This gasket seals the joint between the exhaust manifold and the cylinder head, preventing ...

U-Bolt Nut - 7/16 BSF for use in the leaf spring suspension assembly. U-bolts clamp the leaf spring pack to the axle casing at the front and rear ...

Brake Shoe Spring for the drum brake assembly on Land Rover vehicles. This return spring pulls the brake shoes back from the drum face after each ...

Salisbury Joint Washer for the Salisbury rear axle differential. The gasket seats between the differential carrier and the axle casing, sealing th...

Hub Bearing – inner taper roller bearing for the front and rear wheel hubs. The bearing sits inside the hub and runs on the stub axle, carrying th...

Grommet

Glow Plug Conversion Kit for the 2.25L diesel engine, replacing the original series-wired heater plugs with parallel-wired glow plugs. In the origi...

Door Seal for the rear end door, fitting along the lower floor edge of the side-hinged tailboard. It forms the sealing interface between the foot o...

Brake & Clutch Master Cylinder - Combined CV-Type serves both the braking and clutch hydraulic circuits from a single unit. In this CV-type de...

Brake Master Cylinder is the hydraulic control unit of the braking system, generating the fluid pressure that actuates the wheel cylinders at each ...

Exhaust Bush - Male is the male-profile rubber mounting bush used in the exhaust system vibration isolation assembly. This bush pairs with the cor...

Brake Union Nut - Metric Thread for the hydraulic brake pipe circuit. This union nut seals and secures brake pipe connections at the unions throug...

Wheel Nut securing a road wheel to the hub, clamping the wheel against the hub mounting face. M16 internal thread and steel construction, to the s...

Gasket thermostat by-pass Series 2.25 petrol and diesel.