Land Rover Series 2 & 3 Parts

Oil Filter for Land Rover petrol and diesel engines, part of the engine lubrication circuit. This screw-on canister filter threads onto the filter...

Sump Plug Washer - copper sealing washer for the sump drain plug and thermostat housing on petrol and early diesel engines. The copper washer seat...

Nyloc Nut with a 3/8" UNF thread, used to secure propshaft flange bolts. A nylon insert set into the crown of the nut deforms over the bolt thread...

Hub Bearing - a tapered roller bearing for the front and rear axle wheel ends. It supports the rotating wheel hub on the stationary stub axle, carr...

Clutch Release Bearing installed within the Clutch & Flywheel Assembly, operating between the clutch release fork and the clutch cover diaphrag...

Front cover oil seal

Nyloc Nut with a 1/2" UNF thread, used to retain suspension and steering ball-joint fixings. A nylon insert set into the crown of the nut deforms ...

Hylomar Hylosil 100 is a neutral-curing RTV silicone sealant for gasketing, sealing and bonding in automotive and engineering applications. It cure...

Stop/Tail Light Bulb - 12V 5/21W (trade reference 380) for rear lamp assemblies. This dual-filament bayonet bulb (BAY15d base) provides 5W tail li...

Nyloc Nut with a 3/8" UNF thread and a 12 mm across-flats hex, in the full-height (thick) form. A nylon insert set into the crown of the nut defor...

Fuel Tank Sender Sealing Ring for the fuel tank sender unit assembly. This sealing ring provides the fuel-tight seal between the fuel level sender...

Gasket and Seal Kit for the LT230 transfer box, supplying the gaskets and seals needed to reseal the casing on overhaul. Used when the transfer bo...

Hylomar Universal Blue is a non-setting gasket jointing compound for use on gaskets and machined metal joint faces in automotive and engineering ap...

Inlet Manifold Gasket for the V8 petrol engine, forming the seal between the central inlet manifold casting and the cylinder head intake faces. It...

Hex Nut - 3/8" UNF - Full is a full-height plain hexagonal nut with a 3/8 inch UNF thread, used as a load-bearing imperial-thread fastener. It is ...

Reverse Lamp Bulb - a 21W 12V single-filament incandescent bulb (type P21W) with a BA15s single-contact bayonet cap, fitted to the rear lamp assemb...

Spring Washer fitted under a nut or bolt head to resist loosening from vibration. An M8 split-ring (single-coil) spring washer. The sprung opening...

Track Rod End Boot - Polyurethane for the steering track rod end ball joint. This polyurethane boot fits over the track rod end housing, sealing t...

Split Pin locks a castellated (slotted) nut in place, passing through the nut slots and a cross-drilled hole in the shaft to stop the nut working l...

Universal Joint for the propshaft, transmitting rotational drive between shaft sections while accommodating the angular movement of the driveline. ...

Locknut for body and trim panel fixings. It seats into a pre-formed aperture in the panel to provide a captive threaded point for the screws or bo...

Ignition Lead Set for the 3.5L Rover V8 petrol engine, carrying the high-tension spark from the distributor to the spark plugs. The set comprises ...

Oil Filler Plug serving as the combined fill and level check point for the swivel pin housing, manual gearbox gearcase, and LT230 transfer box on L...

Differential Carrier Gasket for the Rover-type axle assembly. The gasket seals the differential carrier housing against the axle casing at the cen...

Crankshaft Rear Oil Seal for the engine bottom end, fitted at the rear of the crankshaft where it exits the block towards the flywheel. The seal r...

Distributor Rotor Arm for the 3.5L V8 petrol ignition system. The rotor arm sits on top of the distributor shaft beneath the cap and rotates to dis...

Sealing Washer used at sealing interfaces across multiple engine assembly groups. This washer is used in rocker cover and breather assemblies, val...

Anti-Roll Bar Washer used at the anti-roll bar and shock absorber mounting. The washer spreads the clamping load of the retaining nut across the m...

Copper Sealing Washer used across a wide range of sealing applications on Land Rover vehicles. This soft copper washer provides a reliable, leak-f...

Distributor Cap for the ignition distributor on the V8 EFI engine. The cap seats over the distributor and carries the high-tension current from th...

Ignition Coil - high-tension coil in the ignition system. Converts the low-voltage supply into the high-tension voltage required to fire the spark...

Engine Oil - 15W40 Multigrade mineral engine lubricant for older petrol, diesel, and LPG engines. 15W40 multigrade viscosity provides reliable lub...

Gear Oil - EP80W90 extreme-pressure gear lubricant for manual gearboxes, transfer cases, and axle drives. The EP80W90 grade combines extreme-press...

Self-Locking Nut with a 5/16" UNF thread and a 1/2" across-flats hexagon. The self-locking action resists loosening under vibration, retaining cla...

Distributor Module for the 3.5L Rover V8 petrol engine, used with the earlier single-coil electronic ignition system. It forms part of the distribu...

CuNiFer Brake Pipe, 3/16" outer diameter, supplied for the brake hydraulic circuit. The copper-nickel alloy resists corrosion and is soft enough to...

Coolant Temperature Sensor - V8 EFI for the engine management system. This sensor monitors coolant temperature and sends a continuous signal to th...

Inlet Manifold Seal for the V8 petrol induction system, straight pattern. The seal closes the joint between the underside of the inlet manifold an...

Hex Nut - 1/4" UNF is a plain hexagonal nut with a 1/4 inch UNF thread, used as a general-purpose imperial-thread fastener throughout the chassis, ...

Nut - M6 is a plain M6 hexagonal nut used as a general-purpose threaded fastener throughout the chassis, body and mechanical assemblies. It tighte...

Oil Seal for the front axle swivel pin housing. Seals the front driveshaft where it passes into the inner end of the swivel housing, retaining axl...

Crankshaft Oil Seal - Rear seals the rear of the crankshaft where it leaves the cylinder block at the flywheel end, retaining oil within the bottom...

Side Cover Gasket sealing the cylinder-block side cover (tappet inspection cover) to the block face on diesel engines. The side cover closes the p...

Swivel Housing Washer for the swivel pin housing drain plug, part of the front axle swivel assembly. The sealing washer fits beneath the drain plu...

Brake Pipe Union - a male tube-nut fitting that secures a flared 3/16" (4.75mm) hydraulic pipe end into a female union, T-piece or cylinder port. ...

Front Cover Gasket seals the timing cover to the front face of the cylinder block on the V8 petrol engine. It fits between the front cover and the...

Taper Roller Bearing - Diff Pinion - Outer is the outer pinion bearing in the differential final drive assembly, supporting the pinion shaft where ...

Shock Absorber Washer for the rear suspension, outer position. This washer fits over the rear shock absorber mounting, seating against the rubber ...