Land Rover Series 2 & 3 Parts

Washer for the windscreen and handbrake assembly on Series 2, Series 3, and Military Land Rover vehicles.

Pedal Pivot Bush is the bearing bush on which the clutch or brake pedal pivots within the pedal box assembly. Pressed into the pedal bore, it prov...

Retainer

Thrust Washer for the 2nd gear assembly within the manual gearbox. Fitted to the mainshaft to control the end float of 2nd gear, the washer is sel...

Stud A threaded fastening stud catalogued for use across multiple applications. It is fitted in several locations on the engine and its ancillarie...

Return Spring for Series hydraulic actuator and throttle control assemblies. This spring serves as a return spring in the hydraulic actuator assem...

Steering Wheel is a 15-inch three-spoke replacement wheel that mounts to the steering column. It is supplied without a boss, so a separate fitting...

Fuel Tank Sender for the rear-mounted fuel tank on long-wheelbase diesel applications. The sender unit fits into the top of the fuel tank, where a...

Lower Steering Drop Arm for the steering relay assembly. This is the lower lever that clamps to the bottom of the steering relay shaft. Within the...

Push Rod for the petrol-engine valve train. Each push rod transfers motion from the camshaft follower to the rocker arm to open the valve. Fitted ...

Fuse box

Crankshaft Key locates the timing gear and crankshaft pulley on the crankshaft nose, fixing their angular position relative to the shaft. It trans...

Sill Panel - LH

Rear Propeller Shaft for the rear driveline. The propeller shaft transmits drive from the transfer box rear output flange to the rear axle differe...

Oil Pump Relief Valve Spring - sets the pressure at which the oil pump's relief valve opens. It holds the relief valve plunger closed against the ...

Mounting Plate for the rear door spare wheel carrier assembly. This steel retainer plate secures the spare wheel against the tailgate-mounted spar...

Coloured Lamp Kit is a complete set of 73mm round lamps for the front and rear lighting positions, supplied with coloured lenses. The kit contains...

Steering Column Lock for diesel applications, mounted on the upper steering column. The assembly clamps around the column and combines the anti-th...

Engine Plug - a threaded blanking plug used to seal machined ports and drillings in the engine, including locations in the cylinder head and the oi...

Fuel Gauge is a 12V dash-mounted instrument that displays the amount of fuel remaining in the tank. Fitted within the instrument panel, it receive...

Rear End Door Hinge Kit replaces the full set of hinges that carry the rear end door on the body. The kit contains three hinges in a zinc-plated f...

Shock Absorber - rear suspension damper for the short-wheelbase chassis. Mounted between the rear axle and the chassis bracket, it controls spring...

Contact Set - Lucas Distributor is the breaker-point set for the ignition distributor. Mounted on the distributor baseplate, the points are opened...

Ignition Condenser for the contact-breaker distributor, of the Lucas type, supplied with a long lead (17-7/8 in). Wired across the contact-breaker...

Rear Safari Door Seal Kit for the Safari-style rear door assembly on Series 2, 2A, and Series 3 Land Rovers. This kit contains all the rubber seal...

Exhaust Fitting Kit supplies the seals and fixings needed to install and join a complete exhaust system on the short-wheelbase (SWB) chassis. The ...

Strap Stud is a body fixing used in the canvas hood (soft top) and hood frame assembly. It provides an anchor point over which a retaining strap i...

Cylinder Head to Block Stud for the four-cylinder diesel engines - 2.25L and 2.5L naturally-aspirated. The stud threads into the cylinder block dec...

Door Hinge Bolt - countersunk UNF type - within the door assembly. This countersunk fixing bolt secures the door hinge plate to the door face, com...

Circlip - Bonnet Prop Pin is the retaining circlip that secures the pin on the bonnet prop assembly. The circlip locates in a groove on the prop p...

Switch - Fuel Tank Tap is an electrical switch used to operate the fuel tap selection on Land Rover Series I, Series II, Series IIA, and Series III...

Starter Motor for V8 petrol engines, operating within the engine electrical starting system. The solenoid-actuated pinion engages the flywheel rin...

Main Bearing Set for the crankshaft main bearings in the engine bottom end. The bearing shells locate between the crankshaft main journals and the ...

Thrust Washer for the gearbox mainshaft, 0.128" thick. This is a selective-thickness thrust washer used to set mainshaft end-float during gearbox ...

Lamp Boot - Military is a rubber protective boot for military-specification lamp assemblies. The boot fits over the lamp body to provide a weather...

Thrust Washer - 0.130" A gearbox mainshaft thrust washer for the second-speed gear, 0.130" thick. It controls the end-float of the 2nd-speed gear ...

Plastic Washer serves as a spacing and anti-friction washer at the front seat hinge and the rear door check arm pivot. Fitted at the pivot joint, ...

Static Three-Point Seat Belt for the front seating position, combining a lap strap and a diagonal shoulder strap in a single restraint. This is a ...

Special Bolt for retaining the tappets in the cylinder block, part of the camshaft and tappet assembly. This is a specific-design fastener that se...

Sedimentor Drain Plug Seal for the sedimentor in the diesel fuel supply. The sedimentor separates water and heavier contaminants from the fuel ahea...

Fuel Tank Outrigger - front right-hand chassis outrigger supporting the fuel tank on the short-wheelbase 88" chassis. Welded to the chassis frame,...

Free-Wheeling Hub Repair Kit for 24-spline manual free-wheeling hubs. Manual free-wheeling hubs allow the front drive members to be disengaged fro...

Circlip An external retaining circlip for the gearbox primary pinion shaft. It seats in a machined groove on the shaft to retain the primary pinio...

Washer - a plain flat washer used as a general-purpose fastening component across many assemblies on the vehicle. Fitted under a bolt head or nut,...

Screw 3/8" UNC x 1-1/2" used to secure the starter motor to the engine block on Rover V8 petrol engine applications. This is a 3/8 inch Unified Nat...

Plain Washer with a 1/4" bore, used as a general-purpose flat washer. Fitted under a bolt head or nut, it spreads the clamping load over a wider a...

Door Pillar Bracket for the right-hand (offside) bulkhead door pillar, supplied as the bottom bracket only (less the pillar). The bracket forms th...

Fuel Tank Bolt secures the front mounting of the fuel tank to the chassis, for tanks mounted beneath the front seat. It clamps the tank's forward ...