Land Rover Series 2 & 3 Parts

Brake Pipe Clip – Double secures a pair of brake pipes along their routing through the braking hydraulic circuit, retaining both lines against the ...

Staple Clamp for the soft top canvas hood, part of the rear body tie-down hardware. Fixed to the rear body side, it forms the anchor loop that the...

Rocker Cover Gasket (Top) - seals the rocker cover joint on the 2.6L 6-cylinder petrol engine. Fitted between the rocker cover and the cylinder he...

Glazing Rubber Strip - rubber glazing section supplied by the metre. It beds and seals a fixed glass panel into its body aperture, locating the gla...

Hub Bearing – inner taper roller bearing for the front and rear wheel hubs. The bearing sits inside the hub and runs on the stub axle, carrying th...

Headlamp Bezel - black finish. The trim ring that surrounds the 7" round headlamp, retaining the lamp unit in the front panel and finishing the hea...

Track Rod End for the steering linkage, with a left-hand thread and a fully threaded shank. The track rod end forms the ball-jointed connection be...

Static Lap Seat Belt for the second-row seating position, forming part of the interior occupant restraint system. The non-retractable, fixed-lengt...

Plain Washer - imperial-dimensioned flat washer with an internal diameter of 7/16 inch and an outer diameter of 13/16 inch. Used in general fasten...

Hex-head bolt, 3/8" UNC thread, 3/4" long. Unified Coarse (UNC) thread form with a hexagonal head for use with standard imperial spanners and sock...

Hex-head bolt, 5/16" UNF thread, 3/4" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and socke...

Oil Seal for the swivel pin housing on the front axle, sealing against the polished surface of the swivel ball. The seal seats in the rear face of...

T-Piece is a three-way connector in the windscreen washer fluid circuit. It joins the washer hose into two branches, distributing fluid from the p...

Bonnet Buffer is a resilient rubber cushion that forms part of the bonnet closure assembly at the front of the body. It provides the stop the bonn...

Brake Pipe Union - a female threaded union nut for the brake hydraulic pipework, with a 7/16"-20 UNF thread sized for 1/4" brake pipe. It fastens ...

Seat Belt Buckle Catch - left-hand front seat belt stalk receiver forming the fixed lower end of the front LH seat belt assembly. The non-audible c...

Bolt 1/4" UNF x 2" is a hex-head set bolt with a 1/4-inch Unified National Fine (UNF) thread at 28 threads per inch and a 2-inch shank length. It ...

Output Shaft Oil Seal seals the output shaft of the LT95 four-speed gearbox and integral transfer box, retaining gear oil where the shaft passes th...

O-Ring for the engine sump, part of the engine lubrication sealing arrangement. Seals the sump joint to prevent oil leakage. Fitted to four-cylind...

Seat Squab Bolt - shouldered bolt for mounting the seat squab (backrest) to its frame. This shouldered bolt secures the seat squab at its mounting...

Nyloc Nut with a 1/2" BSF thread. A nylon insert in the crown of the nut grips the bolt thread as it is tightened, resisting loosening under vibra...

Door Bottom Seal for the front door. This rubber seal fits along the lower edge of the door, closing the gap between the door bottom and the body t...

Bulb, 12V 4W (type 233, BA9s single-contact bayonet cap). A miniature bayonet bulb used in number plate, side, interior and rear lamp positions.

Rear End Door Hinge Kit replaces the full set of hinges that carry the rear end door on the body. The kit contains three hinges in a zinc-plated f...

Main Bearing Set for the 2.25-litre 4-cylinder engine in its 3-main-bearing form. These are the replaceable shell bearings that carry the crankshaf...

Spark Plug - ignites the air/fuel mixture in the combustion chamber of the petrol engine. It threads into the cylinder head with its electrode gap ...

Joint Washer for the gearbox output shaft housing. This gasket seals the mating face between the output shaft housing and the gearbox casing, prev...

Differential Carrier Bearing is a taper roller bearing that supports the differential carrier within the axle, as part of the crownwheel and pinion...

Hex-head screw, 5/16" UNF thread, 1-1/4" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and so...

Flywheel Housing Stud secures the flywheel housing to the rear of the cylinder block on the 2.0L petrol engine. The stud provides a threaded fixin...

Seat Belt - 3-Point Inertia Reel is a lap-and-diagonal front seat belt assembly with a self-locking inertia reel, supplied to the basic Type A spec...

Clutch Slave Cylinder, part of the hydraulic clutch release circuit. The slave cylinder receives fluid pressure from the clutch master cylinder an...

Spring Washer - M10 single-coil spring lock washer. Fitted beneath a nut or bolt head, the split single-coil section bears against the fastener to...

Starter Motor for the engine starting system - a 12V high-torque gear-reduction unit for petrol applications. The starter mounts to the bellhousin...

Exhaust Pipe Clamp

Transfer Gear Knob - High/Low - LT95 is the hand grip fitted to the high/low range transfer lever on the LT95 gearbox. It threads onto the top of ...

Bolt - threaded fastener with a 7/16" UNF (Unified National Fine) thread and a 2-1/4" length.

Bolt - an imperial hexagon-head bolt with a 5/16" UNF thread and a 2-3/4" shank length. This is an engine-area fixing for early Series application...

Windscreen Washer Non-Return Valve fits inline in the washer fluid delivery pipe, forming part of the windscreen washer system. It allows fluid to...

Inlet manifold stud

Ignition Coil for the V8 petrol ignition system. It converts the low-voltage supply into the high-tension voltage that fires the spark plugs throug...

Single Clip is a single-aperture retaining clip used to secure brake and fuel pipes, the accelerator cable and the hand throttle control. It holds...

Screw with a mushroom head and a 1/4" Acme thread, 1" long, with a sherardized zinc finish. Used as a floor fixing, securing the transfer lever ga...

Exhaust Valve Guide is pressed into the cylinder head to support and align the exhaust valve. It locates the valve stem so the valve seats squarel...

Interior Mirror Bracket mounts the interior rear-view mirror to the body, providing the fixing point for the mirror stem. This is the untrimmed ve...

Lock Washer for the starting dog at the front of the crankshaft. The starting dog threads into the nose of the crankshaft to retain the front pull...

Rear Propshaft for the short-wheelbase chassis, forming part of the driveline between the transfer gearbox and the rear axle. The propshaft transm...

Exhaust Valve Stem Seal for the cylinder head valvetrain. Fits over the exhaust valve stem at the top of the valve guide, metering the oil that pa...