Land Rover Series 2 & 3 Parts

Fuel Pipe Olive

Clevis Pin for the handbrake (transmission parking brake) linkage. This 22mm clevis pin connects the handbrake operating rod to the relay lever, t...

Transfer Box Output Mud Shield Shield that fits over the transfer box output flange to protect the output shaft oil seal from mud, water and debris...

Heater Duct, left-hand side, within the heater air distribution system. Routes air from the heater assembly to the floor-level outlet beneath the ...

Nut - 10/32" UNF A nut with a #10-32 UNF (Unified National Fine) internal thread, run onto a matching UNF bolt or stud to clamp the joint.

Collar Bush for the four-wheel-drive selector mechanism in the two-speed transfer box. It seats on the high-range 4WD selector rod, locating the s...

Diff Pinion Taper Roller Bearing is the inner pinion taper roller bearing in the Salisbury axle differential. It supports the pinion shaft where i...

Pinion Bearing (Outer) for the Salisbury axle differential. It is the outer of the pair of taper roller bearings that carry the drive pinion, seate...

Hex Head Bolt - 1/4" UNF thread, 5/8" long, with a hexagonal head. A general-purpose imperial fastener with a Unified Fine (UNF) thread form, driv...

Clutch Slave Cylinder, part of the hydraulic clutch release circuit. The slave cylinder receives fluid pressure from the clutch master cylinder an...

First Gear Bush for the LT76 gearbox mainshaft. The bush journals the mainshaft first gear, providing the running surface on which the gear turns o...

Snatch Block - a winch recovery pulley used to redirect a winch line or to double its effective pulling capacity. Rated for a 10-tonne working load...

Set Screw - a fully threaded hexagonal-head setscrew with a 5/16" UNF (Unified Fine) imperial thread and a 1-1/8" length. Used as an engine and cha...

Pan Head Screw - a machine screw with a low, rounded-top head and a flat bearing face, used as a general-purpose fixing. Metric M6 thread with a 1...

Side Window Seal is the rubber glazing seal that secures and weatherproofs the fixed side window glass within its body aperture. Part of the body ...

Wing Fixing Plate is a three-stud captive stud plate used in the front body mounting assembly, where it secures the front wing to the radiator (fro...

Spring Washer, M8, a split ring washer used with M8 bolts and nuts to prevent fastener loosening caused by vibration and cyclical loading. The spl...

Rear Stop/Tail Lamp - LED, Smoked - LED combined stop and tail lamp with a smoked lens, supplied as a complete sealed unit to replace the standard ...

Piston for the 2.25L four-cylinder diesel engine, operating within the cylinder block as part of the piston and connecting-rod assembly. The pisto...

High-Tensile Bolt with a 5/16" UNF (Unified National Fine) imperial thread and a 1-1/4" shank length. A hex-head fastener manufactured to a high-t...

Bolt - V8 Inlet Manifold is the fastener that secures the inlet manifold on the Rover V8 petrol engine. It clamps the inlet manifold to the cylind...

Core Plug for the engine casting. Core plugs seal the core holes left in the cylinder block after the casting sand is removed during manufacture. ...

107.5cm long 0.13cm thick

Brake Pedal Return Spring for the pedal box assembly, fitted to servo-assisted braking systems. The spring returns the brake pedal to its rest pos...

Carburettor Torsion Spring is the return spring fitted to the throttle linkage of the Zenith carburettor on the 2.25L four-cylinder petrol engine. ...

Differential Pinion Bearing Spacer used in the axle differential assembly across a broad range of Land Rover models from 1965 onwards. This spacer...

Lock Washer fitted under a nut or bolt head to lock a threaded fastening against loosening. Its sprung form bears against the joint face and the u...

Shim is a 0.002" adjustment shim for the manual (non-power-assisted) steering box. It is fitted within the steering box to set the correct end-flo...

Top Swivel Pin Bearing Spring, part of the front axle swivel pin housing assembly. The spring acts on the top swivel pin bearing to maintain beari...

Snap Ring retaining the rubber dust boot on a track rod end within the steering linkage. A spring-steel ring that seats in the outer groove of the...

Swivel Pin Housing for the front axle, the chrome-finished swivel joint on which the steering swivel and hub assembly pivot. The housing bolts to ...

LED Light Upgrade Kit (deluxe smoked-lens type, 73mm) - a complete set of WIPAC LED lamps with smoked lenses, replacing the original incandescent f...

Steel Road Wheel is a welded steel road wheel with a 6.5 x 16 inch rim, finished in black with a Wolf-style profile for road use with tubeless tyre...

Bolt, 7/16" BSF x 1-3/8" secures the upper swivel pin to the swivel housing in the front axle assembly. The top swivel pin retains the swivel ball...

Main Bearing Set - crankshaft main bearing shells for the 2.25L four-cylinder three-bearing engine. The main bearings support the crankshaft withi...

Steering Drag Link - With Bracket - 73cm is a steering linkage rod, supplied with an integrated steering damper bracket. The drag link transmits s...

Glazing felt strip for the door top sliding glass channel. The felt lines the channel the sliding glass runs in. It cushions the pane, takes up th...

Body is the right-hand sill channel for the Defender, running along the underside of the door aperture in the body structure. This structural chan...

Exhaust Flange forms a bolted joint in the exhaust system of the early 3.5L V8 petrol engine with single downpipes. It provides the sealing face w...

Clutch Master Cylinder Overhaul Kit for rebuilding a CV-type master cylinder, allowing the worn internal components to be renewed without replacing...

Handbrake Stud A mounting stud for the transmission (drum) handbrake within the braking system. It secures the transmission brake back plate to th...

Blind Brake Union - a male threaded fitting used in the hydraulic brake pipe circuit. The body carries a 3/8"-24 UNF male thread but is solid, wit...

Differential Bearing for the Salisbury axle. It is one of the pair of taper roller bearings that carry the differential carrier - the housing holdi...

Connecting Rod Bearing Set for the Rover V8 petrol engine. These are the replaceable big-end shell bearings that fit between the connecting rods an...

Carburettor Float for the Zenith 361V carburettor, part of the Fuel System assembly on Series petrol engines. The float rides on the fuel surface ...

Bolt - a hexagonal-head bolt with an M10 metric thread and a 30 mm length. A common general-purpose fastener used at fixing points across the suspe...

Split Pin: a cotter pin that locks a slotted (castle) nut or retains a clevis pin. After fitting, its legs are bent back to stop the fastening work...

Ignition Coil A high-output sports coil for the ignition circuit. It sits between the low-tension supply and the distributor, converting the primar...