Land Rover Series 2 & 3 Parts

7" round LED headlamp 12/24V black 78W LHD (pair)

Cable Clip for securing the body wiring harness, part of the vehicle electrical system. This clip retains a cable run against the body or chassis,...

Wiper Motor for the windscreen wiper assembly. It converts the electrical supply into rotary motion, driving the wiper transmission and linkage th...

Oil Seal for the front axle swivel pin housing. Seals the front driveshaft where it passes into the inner end of the swivel housing, retaining axl...

CuNiFer Brake Pipe, 3/16" outer diameter, supplied for the brake hydraulic circuit. The copper-nickel alloy resists corrosion and is soft enough to...

Wheel Spanner with a 27 mm socket, a hand tool for removing and refitting wheel nuts. Engages the 27 mm hexagon of the wheel nut to loosen or tigh...

Nut, 1/2" UNF. A threaded fastener used on the early 4-cylinder diesel engine assembly.

Oil Seal - a radial oil seal fitted between the wheel hub and stub axle within the wheel hub and drive shaft assembly. The seal retains lubricant ...

Elbow Gasket seals the coolant outlet elbow, or thermostat housing, to the inlet manifold on the V8 petrol engine, forming part of the engine cooli...

Coolant Temperature Sensor - V8 EFI for the engine management system. This sensor monitors coolant temperature and sends a continuous signal to th...

Coolant Bypass Hose for the thermostat assembly on the 3.5L V8 petrol engine. This hose connects the thermostat housing to the inlet manifold, pro...

Lock Nut - 7/16" UNF - self-locking nut providing a prevailing-torque fastening. The nut resists loosening under vibration and dynamic load, secur...

Oil Filter Gasket for the engine lubrication system, sealing the oil filter bowl to the filter housing on 4-cylinder petrol and diesel engines. Th...

Gearbox Plug Sealing Washer for LT76 and LT77 manual gearbox drain, level, and inspection plugs. This sealing washer fits beneath the thread of ge...

Alternator - charging unit in the vehicle's electrical charging system. Driven from the engine by the accessory belt, it generates current to powe...

Toggle Switch is a two-position on/off switch in the dashboard switchgear, controlling the instrument and panel lighting circuit. The sprung toggl...

Axle Pinion Gasket for the Salisbury rear axle, sealing the pinion bearing retainer to the differential housing at the propshaft flange end of the ...

Fuel Tank Mounting is the moulded rubber isolator in the fuel tank mounting assembly that sits between the tank body and its chassis support. It c...

Grease Nipple with a short thread, used at propshaft universal joint lubrication points. The nipple threads into the grease point and provides the...

Nyloc Nut - 1/4" UNF - self-locking nut with a nylon insert set into the collar. The nylon insert grips the bolt thread to resist loosening under ...

Fuel Filter with a paper filter element, for carburettor petrol engines. Part of the fuel supply system. The filter is plumbed inline between the ...

Oil Pump Gasket for the Rover V8 petrol engine lubrication system. This gasket seals the oil pump to its mating face, maintaining oil pressure and...

Inlet Manifold Seal for the V8 petrol induction system, straight pattern. The seal closes the joint between the underside of the inlet manifold an...

Bolt - 3/8" BSF x 1" hexagonal head bolt to British Standard Fine thread specification. 3/8" BSF (British Standard Fine) thread with a 1" shank le...

Brake Hose - flexible hydraulic line in the rear braking circuit, connecting the chassis-mounted rigid brake pipe to the rear axle brake assembly. ...

Screw with a 1/4" UNF (Unified Fine) thread, 7/8" long, used as a setscrew in body, hinge and mirror-arm fixings. Note: non-metric (imperial UNF) ...

Flasher Relay installed in the indicator and hazard-warning circuit, controlling the flash rate of the turn-signal lamps. This 12V electronic unit...

Clutch Fork Insert is the nylon insulator that fits over the clutch fork pivot pin inside the bellhousing, cushioning the fork at its fulcrum point...

Coolant Hose for the water pump circuit on the 3.5L V8 Twin Carb petrol engine. This hose connects the water pump outlet to the coolant pipe, rout...

Mudflap fitted at the trailing edge of the wheel arch to control road spray, mud and debris thrown from the tyre. Mounted at either the front or r...

Washer Pump for the windscreen washer system, running on a 24-volt electrical supply. The pump draws fluid from the washer reservoir and delivers ...

Ignition Coil - high-tension coil in the ignition system. Converts the low-voltage supply into the high-tension voltage required to fire the spark...

Hex Nut - 1/4" UNF is a plain hexagonal nut with a 1/4 inch UNF thread, used as a general-purpose imperial-thread fastener throughout the chassis, ...

Nut - M6 is a plain M6 hexagonal nut used as a general-purpose threaded fastener throughout the chassis, body and mechanical assemblies. It tighte...

Fan belt OEM DAYCO 10mm wide, 1235mm long

Water Pump Gasket seals the coolant pump to the engine front cover on the V8 petrol engine. It fits at the pump mounting face, sealing the coolant...

Flywheel Housing O-Ring - a sealing ring at the rear of the engine where the flywheel housing meets the cylinder block. Fitted to the 2.25L engine...

Instrument Bulb - 12V 2.2W for the instrument panel. Replacement dial illumination bulb for the speedometer on Range Rover Classic Police Vehicle ...

Track Rod Clamp is a split-tube collar that secures the threaded track rod end into the track rod tube on the front steering axle. Once the front ...

Clutch Fork Clip secures the clutch arm rod to the release fork inside the gearbox bellhousing on LT77, LT85, and R380 5-speed manual gearboxes. T...

Hub Nut Socket is a 52mm deep impact socket with a 1/2" square drive, used to remove and refit the hub retaining nut on the wheel bearing assembly....

Flange Bolt, M8 x 50 mm - a hexagon-head bolt with an integral flange beneath the head. The flange spreads the clamping load over a wider bearing ...

Oil Seal for the front axle swivel pin housing. Seals the front driveshaft where it passes into the inner end of the swivel housing, retaining axl...

Serrated Washer with a 3/8" bore, a serrated locking (shakeproof) washer. Fitted beneath a bolt head or nut, the serrated teeth bite into both the...

Pop Rivet (blind rivet) for fastening panels, trim and brackets where access is only available from one side. The rivet is fitted into a drilled h...

Crankshaft Oil Seal - Rear seals the rear of the crankshaft where it leaves the cylinder block at the flywheel end, retaining oil within the bottom...

Drain Plug - a tapered threaded plug used to seal and drain fluid from engine and driveline housings. It serves as a coolant drain plug in the cyl...

Speedometer Cable – LHD is the mechanical drive cable that transmits road speed to the speedometer. The rotating inner core runs inside a protectiv...