for Discounts / VAT
for Discounts & Correct VAT
Parts for Land Rover Series II, Series IIA, and Series III (1958 to 1985), covering 88-inch short wheelbase and 109-inch long wheelbase configurations. Genuine, OEM, and aftermarket options across engine, body, electrical, suspension, and brake categories. Stocked and shipped from The Hague as part of the full Land Rover Series parts catalogue.
What fits: Series II (1958 to 1961), Series IIA (1961 to 1971), Series III (1971 to 1985), SWB and LWB.
Speedo cable S3
Accelerator Cable links the accelerator pedal to the injection pump throttle lever, forming part of the throttle linkage on the 2.25L diesel engine...
View full detailsNAS Link Lead Extension – a three-wire extension link loom for the rear lighting circuit. It connects the rear stop/tail lamp to the vehicle body ...
View full detailsWiper Drive Cable for the windscreen wiper system on cable (rack) type wiper drives. The flexible toothed cable runs inside the wiper rack tubing ...
View full detailsSpeedometer Cable – LHD is the mechanical drive cable that transmits road speed to the speedometer. The rotating inner core runs inside a protectiv...
View full detailsSpeedometer Cable Plate Screw secures the speedometer cable retaining plate to the gearbox. It clamps the plate that holds the speedometer drive c...
View full detailsSpeedometer Drive Cable transmits rotational drive from the gearbox speedometer take-off to the speedometer head in the instrument panel. An inner...
View full detailsSpeedo cable assy SII
Heater Distribution Control Cable - the Bowden cable that links the dashboard heater control to the air-distribution flap in the heater assembly. ...
View full detailsEngine Stop Cable for the fuel shut-off control of the 2.25L diesel engine. Operating within the fuel injection circuit, the cable links the dashb...
View full detailsHeater Cable operates the tap-type heater control valve in the heating and ventilation system. It connects the dashboard heater control to the tap...
View full detailsEngine Stop Cable is the manual control cable that shuts down the 2.25L diesel engine by pulling the fuel injection pump stop lever to the no-fuel ...
View full detailsAccelerator Cable for the throttle control linkage, transmitting accelerator pedal movement to the carburettor throttle on the 2.25 litre petrol en...
View full detailsWiper Cable Tube - LHD is a guide tube in the cable-and-rack windscreen wiper system, in the left-hand-drive configuration. It houses and routes t...
View full detailsChoke Cable for the carburettor cold-start system. The cable links the dash-mounted choke control to the carburettor, operating the choke mechanis...
View full detailsAccelerator Cable in the throttle control linkage, connecting the accelerator pedal to the carburettor throttle spindle. Transmits pedal movement ...
View full detailscable from accelerator pedal to cross shaft on military Series 3 diesel models
Choke Cable for the DA2126 Weber carburettor conversion. This cable links the dashboard choke control to the carburettor's choke mechanism, provid...
View full detailscable choke S3 - Right Hand Drive 2.25L 4-cylinder petrol fitted with steering column lock, - Left Hand Drive 2.6L 6-cylinder petrol fitted with s...
View full detailsCable Clip for securing wiring harnesses and cables in Land Rover vehicles. Sold individually.
Speedometer Cable for Land Rover models fitted with the 2.6-litre 6-cylinder petrol engine. Transmits rotational drive from the gearbox output shaf...
View full detailsTube wipersystem OEM
Choke Cable for the carburettor cold-start system. The cable links the dash-mounted choke control to the carburettor, operating the choke mechanis...
View full detailsChoke Cable is the manual choke control cable in the carburettor fuel system, running from the dashboard choke knob to the carburettor choke lever....
View full detailsEdge Clip - Door Lock Mechanism with various applications across Land Rover Series, Defender, Discovery 1, and Range Rover Classic models. This sp...
View full detailsDiesel Stop Control Cable operates the engine stop on the diesel injection pump. Pulling the dashboard control draws the cable to move the fuel sh...
View full detailsTrip Reset Cable for the Land Rover Series III speedometer assembly. The cable connects to the trip odometer reset mechanism within the speedometer...
View full detailsCable Clip - Stainless Steel for routing and securing cables and wiring harness runs to bodywork and chassis members on the Land Rover. The stainle...
View full detailsAccelerator Cable Throttle cable in the engine throttle linkage, transmitting accelerator pedal movement to the throttle control. Supplied for rig...
View full detailsHandbrake Actuating Rod in the linkage of the transmission-mounted drum handbrake. The rod transmits movement from the handbrake lever to the expa...
View full detailsSpeedometer Cable for the Land Rover speedometer drive system. Transmits rotational drive from the gearbox output shaft to the speedometer head, pr...
View full detailsBattery Cable for the 24V electrical system. This is a battery link cable, connecting the two batteries so they supply the vehicle's 24-volt circu...
View full detailsTube
Accelerator Cable connecting the accelerator pedal to the throttle linkage on the 3.5L V8 petrol engine. The cable transfers pedal travel to the c...
View full detailsScrew, M6 x 45, used as a threaded fastener at several points in the drivetrain and pedal assemblies. It secures the lower bellhousing cover to th...
View full detailsAccelerator Cable Dutch Lightweight Diesel
Stop Cable Diesel Without Steering Column Lock RHD
Parts for Land Rover Series II, Series IIA, and Series III, produced from 1958 to 1985. Covers short wheelbase (88-inch) and long wheelbase (109-inch) configurations. Series I is a separate collection. Use your Commission Number to confirm fitment before ordering.
This collection covers Land Rover Series II (1958 to 1961), Series IIA (1961 to 1971), and Series III (1971 to 1985) in both short wheelbase and long wheelbase configurations. It does not cover Series I vehicles. Series I parts are held in a separate collection.
The three generations in this collection share the same core body-on-frame ladder chassis, a two-speed transfer gearbox, and a four-speed manual main gearbox. Wheelbase options from Series II onward were 88 inches (short wheelbase, referred to as SWB) and 109 inches (long wheelbase, referred to as LWB). Parts compatibility is not uniform across the three generations, and wheelbase is a fitment variable for a significant number of components including body panels, wiring looms, propshafts, and floor sections.
The 2.25-litre petrol and diesel engines are shared across Series IIA and Series III, and engine internals for these units carry across both generations in most cases. Other components, including wiring configurations, swivel housing seals, and certain axle parts, differ between generations and between sub-variants within the Series III production run. A 1980 update introduced five main bearing crankshafts to the 2.25-litre engines. A 1982 update increased the Series III half shaft drive spline count from 10 to 24, which affects axle half shaft selection for late Series III vehicles.
LWB Series IIA models were available with a 2.6-litre straight-six petrol engine. Series III LWB models used the Salisbury rear axle as standard. The Stage 1 V8 variant, produced from 1979 to 1985, used a 3.5-litre Rover V8 and the LT95 gearbox; this was an LWB-only production variant with some component differences from standard Series III specification.
The Land Rover UK heritage pages cover the original design and production history of the Series family and are a useful background reference for owners identifying their vehicle's generation and specification.
Series Land Rovers do not carry a modern 17-digit VIN. Instead, each vehicle has a Commission Number stamped on a plate fixed to the bulkhead. This number encodes the series, engine type, wheelbase, and approximate build date. Confirming your Commission Number before ordering is the most reliable way to ensure parts match your specific vehicle.
The Land Rover Heritage Trust holds production records and Commission Number data for the full Series family and is the definitive reference for vehicle identification on older or incomplete builds.
If you are uncertain about your generation or wheelbase, contact Budget Parts with your Commission Number before placing an order. The team will confirm applicable fitment from the catalogue.
Fitment NotesParts compatibility across this collection varies by generation, wheelbase, and in some cases by build date within a generation. The table below summarises the key fitment variables.
| Generation | Production | Wheelbase options | Engines | Key fitment notes |
|---|---|---|---|---|
| Series II | 1958 to 1961 | 88-inch SWB, 109-inch LWB | 2.0-litre petrol (early), 2.25-litre petrol, 2.0-litre diesel | Some early SWB models used the Series I 2.0-litre engine |
| Series IIA | 1961 to 1971 | 88-inch SWB, 109-inch LWB | 2.25-litre petrol, 2.25-litre diesel, 2.6-litre I6 (LWB only) | Highest-volume sub-series; many mechanical parts cross to early Series III |
| Series III | 1971 to 1985 | 88-inch SWB, 109-inch LWB | 2.25-litre petrol, 2.25-litre diesel, 2.6-litre I6, 3.5-litre V8 petrol | Stage 1 V8 was LWB only (1979 to 1985); 1980 crank update and 1982 half shaft spline update affect part selection; Salisbury rear axle standard on LWB |
When browsing this collection, use the Model filter to narrow results to Series 2 and 3 fitment. For components where SWB and LWB variants differ, product listings identify the applicable wheelbase.
Parts CategoriesThis collection holds over 2,300 parts across all major categories for Series II, IIA, and Series III vehicles. The categories with the heaviest demand from restoration and maintenance buyers are listed below.
Engine and drivetrain components include gaskets, seals, bearings, timing components, and oil system parts for the 2.25-litre petrol and diesel units. Axle half shafts, differential seals, and swivel housing parts are stocked for both SWB and LWB configurations.
Electrical and wiring components include complete wiring loom kits for Series II, IIA, and III in both SWB and LWB. Left-hand and right-hand drive variants are stocked where available. Connectors, fuses, switches, and earthing hardware are held as individual items.
Body and chassis components include bulkhead sections, floor pans, footwell repair panels, rear crossmembers, door bottoms, sills, and tub panels. These are restoration-critical items for vehicles requiring MOT or RDW structural certification.
Brake system components include brake shoes, wheel cylinders, master cylinders, brake lines, and hardware kits. Correct selection requires confirmation of axle type and wheelbase.
Suspension and steering parts include leaf spring sets for SWB and LWB, shock absorbers, polyurethane bush kits, track rod ends, drag links, and steering box rebuild components.
Clutch and gearbox components include clutch kits, release bearings, and seals for the four-speed main gearbox and two-speed transfer box.
Cooling and fuel system parts, lighting components, interior hardware, and service consumables are stocked across the full generation range.
For component-type browsing across all Land Rover models with model filter support, the following category collections include Series-compatible stock.
Brake shoes, wheel cylinders, master cylinders, brake lines, and hardware kits across the Land Rover range.
Land Rover brake parts →Leaf springs, shock absorbers, bush kits, track rod ends, and steering components for Series and later models.
Land Rover suspension parts →Wiring looms, connectors, switches, fuses, and earthing hardware for all Land Rover generations.
Land Rover electrical parts →Bulkhead sections, floor pans, footwell repair panels, rear crossmembers, sills, and tub panels.
Land Rover chassis and body parts →Every product in this collection is labelled with one of three quality designations: Genuine, OEM, or Aftermarket.
Genuine parts carry the original Land Rover part number and were manufactured by or for Land Rover. For Series II, IIA, and III vehicles, genuine Land Rover stock is limited across most categories due to the age of the range. Where genuine parts are listed, they represent original-specification components.
OEM parts are manufactured to the same specification as the original component, frequently by the same supplier that produced the original part, but sold outside the main brand distribution channel. For mechanical rebuilds on Series vehicles, OEM-specification parts are the standard choice used by workshops across Europe.
Aftermarket parts are independently manufactured to a compatible specification. Quality varies by product and by category. For consumable hardware, body repair panels, and service items on Series vehicles, quality aftermarket parts are the practical choice and are used routinely in professional restorations.
Each product listing identifies its quality tier clearly.
Trade BuyersBudget Parts supplies restoration workshops, fleet operators, and independent garages across the EU. Trade customers running regular Series II or Series III projects can open a trade account for volume pricing, consolidated order options, and correct EU VAT invoicing. For components not currently visible in the catalogue, the sourcing team works with UK and EU supplier networks to locate unlisted parts.
Contact the team with your Commission Number and part requirement.
Technical GuidesThe following guides cover technical background and restoration considerations for Series II, IIA, and Series III vehicles.
Covers the engineering and production history of Series II, IIA, and III, including the key differences between sub-variants, engine fitment across generations, and why certain parts interchange while others do not.
Series 2 and 3 history and engineering →A cross-model diagnostic guide covering fuel system fault finding, relevant to carburetted Series vehicles where starting and fuel delivery issues are a common maintenance challenge.
Land Rover fuel system diagnosis →Covers clutch fault identification across Land Rover models, applicable to the four-speed manual gearbox and clutch assemblies used in Series II, IIA, and Series III.
Land Rover clutch fault diagnosis →Interchangeability within this range is partial and depends on generation, wheelbase, and build date. Engine internals for the 2.25-litre petrol and diesel units carry across Series IIA and Series III in most cases. Certain axle and drivetrain components also share fitment between the two generations. However, body panels, wiring looms, swivel housing components, and some suspension parts differ between generations and between SWB and LWB configurations. A 1980 update to Series III crankshafts and a 1982 update to Series III half shaft splines mean that late Series III axle parts are not always interchangeable with earlier Series III or Series IIA equivalents. Confirm by generation, wheelbase, and build date before ordering.
Series Land Rovers use a Commission Number rather than a modern VIN. This number is stamped on a plate fixed to the bulkhead and encodes the series, engine type, wheelbase, and approximate build date. The Commission Number is the most reliable starting point for confirming which parts apply to your vehicle. The Land Rover Heritage Trust holds production records for the full Series family and can assist with identification on older or incomplete builds. Budget Parts can also confirm fitment from the catalogue if you provide your Commission Number before ordering.
This collection covers all three: Series II (1958 to 1961), Series IIA (1961 to 1971), and Series III (1971 to 1985), in both short wheelbase (88-inch) and long wheelbase (109-inch) configurations. Series I vehicles are not covered here. Series I parts are held in the Land Rover Series 1 Parts collection. If you are unsure which generation your vehicle belongs to, use your Commission Number to confirm before selecting parts.
SWB stands for short wheelbase and LWB for long wheelbase. From Series II onward, the standard wheelbase options were 88 inches (SWB) and 109 inches (LWB). Wheelbase directly affects the fitment of body panels, floor sections, wiring looms, propshaft lengths, and certain suspension and brake components. When ordering, confirming your wheelbase is as important as confirming your generation. Product listings in this collection identify wheelbase applicability where SWB and LWB variants differ.
Yes. This collection includes complete wiring loom kits for Series II, IIA, and Series III in SWB and LWB configurations. Petrol and diesel variants are stocked where applicable, and left-hand and right-hand drive options are held where available. The correct loom for your vehicle depends on your generation, wheelbase, drive side, and engine type. Confirming these details before ordering, or contacting Budget Parts with your Commission Number, is the most reliable way to select the correct kit.
This collection stocks a range of body and chassis repair panels for Series II, IIA, and Series III vehicles. Available items include bulkhead sections, footwell repair kits, floor pans, rear crossmembers, door bottom repair sections, and sill panels. These panels are relevant for vehicles requiring structural certification under MOT or RDW inspection. Correct panel selection depends on your wheelbase and, in some cases, your build year within the Series III production run. If you are unsure, contact Budget Parts with your Commission Number before ordering.
Yes. Budget Parts is based in The Hague, Netherlands, and ships to customers across the EU and beyond. EU customers receive invoices with correct VAT treatment. Trade customers and workshops with regular requirements can open a trade account for volume pricing and consolidated ordering. For parts not currently listed in the catalogue, the sourcing team can locate components through UK and EU supplier networks.