Land Rover Series 2 & 3 Parts

Brake Pipe Clip - single-bore retaining clip for securing a rigid brake pipe to the chassis or body structure. This clip holds the brake pipe in i...

Air Filter Element for the 3.5L V8 Twin Carb petrol engine air intake. This filter element is fitted in the air intake housing ahead of the carbur...

Distributor Rotor Arm for the 3.5L V8 petrol ignition system. The rotor arm sits on top of the distributor shaft beneath the cap and rotates to dis...

Manifold Gasket - inlet to exhaust manifold gasket for the 2.25L 4-cylinder petrol engine. On this engine, the inlet and exhaust manifolds bolt to...

Gear Oil - EP80W90 extreme-pressure gear lubricant for manual gearboxes, transfer cases, and axle drives. The EP80W90 grade combines extreme-press...

Clutch Release Plate for the LT77 5-speed manual gearbox clutch release assembly. This mounting plate fastens the external hydraulic clutch slave ...

Rubber Mat Set for the front footwells - a pair of moulded rubber floor mats covering the driver and passenger sides of the cab floor. The mats ar...

Door Hinge for the rear end (load/tail) door, lower position. One of the pair of side-hinged door hinges that mount the rear door to the body aper...

Thermostat - 88°C for the cooling system of V8 petrol engines. The thermostat regulates coolant flow between the engine block and the radiator, al...

Cable Clip for securing the body wiring harness, part of the vehicle electrical system. This clip retains a cable run against the body or chassis,...

Sliding Window Seal for the front door assembly. This rubber seal fits to the front face of the sliding side window, sealing the glass against the ...

Output Shaft Oil Seal seals the front or rear output shaft of the LT76 transfer gearbox, retaining lubricant within the transfer case and preventin...

Shackle Pin (9/16 UNF × 4-3/8 in.) for the rear leaf spring assembly on Land Rover Series vehicles. This is the short shackle pin, fitted at the r...

Rear Mudflaps - a pair of rear mudflaps for the 88in short-wheelbase, fitted behind the rear wheels to deflect road spray and debris thrown up by t...

Lights and Heater Toggle Switch - a three-position Lucas-type toggle switch fitted to the dashboard switchgear. It acts as the master control for t...

Lock Plate for the front axle assembly. This metal tab washer locks fastener heads in position by bending a tab against the bolt head or nut after...

Anti-Roll Bar Washer used at the anti-roll bar and shock absorber mounting. The washer spreads the clamping load of the retaining nut across the m...

Brake Pipe - Wheel Cylinder is a rigid hydraulic brake pipe in the front brake circuit, running from the brake backplate to the flexible jump hose....

Transfer Box Output Shaft Felt Seal for the Series II and Series III LT15 transfer box. The waxed felt seal fits around the rear output shaft and ...

Lock Nut - 7/16" UNF - self-locking nut providing a prevailing-torque fastening. The nut resists loosening under vibration and dynamic load, secur...

Front direction indicator lamp for the vehicle lighting system. This unit provides the flashing directional signal function at the front of the v...

Copper Sealing Washer used across a wide range of sealing applications on Land Rover vehicles. This soft copper washer provides a reliable, leak-f...

Oil Filter Gasket for the engine lubrication system, sealing the oil filter bowl to the filter housing on 4-cylinder petrol and diesel engines. Th...

Clutch Cylinder Adaptor - a pipe union that connects the hydraulic clutch supply pipe to the inlet port of the clutch master cylinder. Fitted at t...

Glass Run Channel for the door window aperture, supplied in a 2 m length. The channel lines the door frame to guide and seat the side window glass...

Wheel Spanner with a 27 mm socket, a hand tool for removing and refitting wheel nuts. Engages the 27 mm hexagon of the wheel nut to loosen or tigh...

Wiper Drum Adaptor - splined adaptor used in the windscreen wiper system to connect the wiper arm to the splined wiper spindle. The adaptor seats ...

Side Cover Gasket sealing the cylinder-block side cover (tappet inspection cover) to the block face, for petrol and diesel engines. The side cover...

Fuel Filler Hose for the rear fuel tank on long-wheelbase models. This flexible hose forms the filler neck connection, carrying fuel from the body-...

Lock Barrel & Key Set for the door locks. This set contains two lock barrels and two keys, supplied without a steering column lock. For the an...

Engine Oil - 15W40 Multigrade mineral engine lubricant for older petrol, diesel, and LPG engines. 15W40 multigrade viscosity provides reliable lub...

Fuel Filter for the diesel fuel delivery system, separating dirt, debris and water from the fuel before it reaches the injection pump. Fitted in t...

Door Hinge Bolt for attaching door hinges to the body structure. This countersunk bolt secures the hinge plate to the hinge assembly, providing a ...

Wheel Cylinder for the rear drum brake assembly, left-hand side. The wheel cylinder forms part of the hydraulic drum brake circuit, converting hyd...

Oil Seal - a radial oil seal fitted between the wheel hub and stub axle within the wheel hub and drive shaft assembly. The seal retains lubricant ...

Exhaust Bush - Female is the female-profile rubber mounting bush used in the exhaust system vibration isolation assembly. This bush pairs with the...

O-Ring - an elastomer seal used at the oil cooler pipe connection within the engine oil cooler circuit. It seats in the union between the oil cool...

Coolant Bypass Hose for the thermostat assembly on the 3.5L V8 petrol engine. This hose connects the thermostat housing to the inlet manifold, pro...

Oil Seal installed within the wheel hub assembly to retain lubricant and prevent contamination ingress at the hub-to-stub-axle interface. The seal...

Detent Spring for the manual gearbox gear selector mechanism. The spring loads the detent ball against the selector shaft, holding the selected ge...

Hinge Pin Kit containing the replacement hardware for door and rear tailgate hinges on Series and early Defender models. Fits the front and rear d...

CuNiFer Brake Pipe, 3/16" outer diameter, supplied for the brake hydraulic circuit. The copper-nickel alloy resists corrosion and is soft enough to...

Distributor Cap for the ignition distributor on the V8 EFI engine. The cap seats over the distributor and carries the high-tension current from th...

Rear Drum Brake Shoe Set covering one full axle, sized for 11-inch rear drum brakes. The shoes carry the friction linings that press outward agains...

Ignition Coil - high-tension coil in the ignition system. Converts the low-voltage supply into the high-tension voltage required to fire the spark...

Lock Washer for the gearbox mainshaft, securing the special retaining nut where the mainshaft meets the transfer box. A tab washer whose tang is b...

Axle Pinion Gasket for the Salisbury rear axle, sealing the pinion bearing retainer to the differential housing at the propshaft flange end of the ...

Rocker cover rubber washer petrol