Land Rover Series 2 & 3 Parts

Track Rod End with left-hand thread, part of the steering linkage. The track rod end connects the track rod to the steering arm through a ball joi...

Track Rod End for the steering linkage, with a right-hand thread. The track rod end is a ball-jointed coupling at the end of the track rod that co...

Clutch Repair Kit for the Land Rover Series III clutch assembly. The kit renews the friction and engagement components of the single dry-plate clut...

Headlamp Bezel - black finish. The trim ring that surrounds the 7" round headlamp, retaining the lamp unit in the front panel and finishing the hea...

Hex-head screw, 1/4" UNF thread, 3/4" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and socke...

Spark Plug - ignites the air/fuel mixture in the combustion chamber of the petrol engine. It threads into the cylinder head with its electrode gap ...

Drain plug

Joint Washer for the gearbox output shaft housing. This gasket seals the mating face between the output shaft housing and the gearbox casing, prev...

Rocker Cover Gasket (Exhaust Side) - seals the exhaust-side rocker cover joint on the 2.0L IOE (inlet-over-exhaust) engine. Fitted between the roc...

Differential Carrier Bearing is a taper roller bearing that supports the differential carrier within the axle, as part of the crownwheel and pinion...

Hex-head screw, 5/16" UNF thread, 1-1/4" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and so...

Gear Knob - LT95 is the hand grip fitted to the main gear lever of the LT95 4-speed gearbox. It threads onto the top of the gear lever and provide...

Exhaust Clamp Plate for the exhaust system, used at the front-pipe and catalyst joint. The plate works together with a U-bolt to draw the exhaust c...

Lucar Connector - a fully insulated two-way in-line electrical connector for joining wiring within the loom. Of the Lucar (blade) terminal type, i...

Shakeproof Washer – a serrated, externally toothed lock washer used at the clutch hydraulic hose union. The teeth bite into both the mating surfac...

Breather Set Screw secures the breather to the rocker cover within the engine crankcase ventilation arrangement. It retains the breather against t...

Steering Rocker Shaft Bush - a bearing bush within the steering relay assembly. The bush locates and supports the rocker (relay) shaft inside the ...

Timing Cover Mudshield is the pressed shield that fits over the timing cover at the front of the engine. It screens the timing case and front pull...

Exhaust Pipe Clamp

Swivel Housing Kit for the front axle swivel assembly, covering one side of the axle. This is the later configuration, with the steering arm mounte...

Anti-Burst Door Lock for the left-hand front door, the latch mechanism that secures the door to the body. The latch engages the striker on the doo...

Rear Crankshaft Packing Strip (T-Piece) forms part of the rear crankshaft oil seal arrangement at the back of the cylinder block. The T-piece pack...

Bolt - threaded fastener with a 7/16" UNF (Unified National Fine) thread and a 2-1/4" length.

Seat Belt Buckle Catch - left-hand front seat belt stalk receiver forming the fixed lower end of the front LH seat belt assembly. The non-audible c...

Bolt with a 5/16" UNF (Unified National Fine) imperial thread and a 1-1/2" shank length. A hex-head fastener for general assembly and fixing appli...

Exhaust Manifold Stud secures the manifold to the cylinder head on the 4-cylinder engine. It threads into the head and carries the manifold flange...

Fuel Pump Repair Kit for overhauling the mechanical diaphragm lift pump on the 2.25 four-cylinder petrol engine. Wear in the pump internals reduce...

Inlet manifold stud

Ignition Coil for the V8 petrol ignition system. It converts the low-voltage supply into the high-tension voltage that fires the spark plugs throug...

Screw with a mushroom head and a 1/4" Acme thread, 1" long, with a sherardized zinc finish. Used as a floor fixing, securing the transfer lever ga...

Head Gasket - 3.5L V8 - Metal is the cylinder head gasket for the 3.5L V8 petrol engine, sealing the joint between a cylinder head and the engine b...

Synchro Cone – LT76 is a synchroniser ring from the synchromesh assembly of the LT76 manual gearbox. It is the friction component that brings the g...

Exhaust Valve Guide is pressed into the cylinder head to support and align the exhaust valve. It locates the valve stem so the valve seats squarel...

Joint Washer for the radiator cap, part of the engine cooling system. This sealing washer seats between the radiator cap and the filler neck, main...

Oil Filler Cap O-Ring seals the oil filler cap to the rocker cover. It forms an oil-tight seal at the cap-to-cover joint, preventing oil leakage a...

Transfer Box Intermediate Shaft Shim, 0.005in thick, used in the transfer box to set the end float of the intermediate gear on its shaft. Selectiv...

Fuel Pipe Olive for the fuel supply line. The olive is the compression ferrule that seats between the fuel pipe and its union fitting. When the un...

Gearbox Thrust Washer for the intermediate gear (laygear) in the main gearbox, used on 4-cylinder applications. It locates against the intermediat...

Selector Detent Spring is part of the gearbox gear-selection detent for the forward-gear selector shafts (1st/2nd and 3rd/4th). It loads the deten...

Interior Door Lock Button, right-hand, of the interior door furniture. The thumbscrew-type lock button that operates the door lock from inside the...

Interior Mirror Bracket mounts the interior rear-view mirror to the body, providing the fixing point for the mirror stem. This is the untrimmed ve...

Cable Grommet for the wiring loom, fitting a 41.5 mm panel hole and accepting a cable of up to 6 mm. Made of black rubber, it lines the hole where...

Lock Washer for the starting dog at the front of the crankshaft. The starting dog threads into the nose of the crankshaft to retain the front pull...

Exhaust Bracket for the exhaust system on left-hand drive vehicles. This bracket supports and locates the exhaust along its run beneath the vehicl...

Lock Plate for the rear drum brake shoe retainer. This fold-over tab plate locks the two screws that secure the brake shoe bottom retainer ring. I...

Rear Propshaft for the short-wheelbase chassis, forming part of the driveline between the transfer gearbox and the rear axle. The propshaft transm...

Sealing Washer for the carburettor choke switch on petrol engine applications. Fitted at the choke switch, it seals the joint at the fitting to pr...

Gear Lever Retaining Spring The spring that retains the main gear lever in its ball housing on the gearbox top cover. It bears down on the lever's...