Land Rover Series 2 & 3 Parts

Front Towing Eye / Lifting Ring bolts to the front of the chassis, providing an anchored attachment point for towing, recovery and lifting. The ri...

Shock Absorber for the rear suspension, forming part of the rear axle damping assembly. This telescopic hydraulic damper is fitted between the cha...

Shock Absorber for the front axle, damping suspension movement by converting the energy of spring oscillation into heat as the axle moves relative ...

double washer, restrictor

Radiator for the engine cooling system, mounted at the front of the vehicle to dissipate heat from the coolant circulated by the water pump. Air dr...

Oil Pump O-Ring, a seal within the engine oil pump assembly. The O-ring seals the oil pump strainer (pickup) joint, maintaining the suction seal s...

Carburettor Manifold Gasket - the gasket that seals the inlet and exhaust manifold assembly to the cylinder head face on carburettor-fed engines. ...

Inline Fuel Filter for petrol engines, fitted in the low-pressure fuel supply line between the tank and the fuel pump or carburettor. This sealed ...

Rear End Door Hinge Kit replaces the full set of hinges that carry the rear end door on the body. The kit contains three hinges in a zinc-plated f...

Front Door Hinge Kit for renewing the front door hinges. The kit includes 4 zinc-plated hinges with stainless steel Torx head bolts and fixings.

Shock Absorber Washer Retaining washer for the rear shock absorber lower mounting. Part of the rear suspension assembly, it locates over the lower...

Swivel Housing Repair Kit for the front axle swivel assembly, covering one side of the axle. This kit excludes the swivel housing itself and suppli...

Track Rod Clamp Kit secures the track rod within the steering linkage assembly, holding the joint in position so the steering geometry stays set. ...

Door aperture sealing rubber supplied in a continuous 30 metre roll for use within the body sealing system. This profile installs along the door a...

Centre floor mounted storage cubby box providing an enclosed compartment between the front seats and additional cup holder provision within the int...

Crankshaft Timing Chain Sprocket The drive sprocket mounted on the nose of the crankshaft within the timing chain drive of the Rover V8 petrol engi...

Parabolic Spring and Shock Kit - a front leaf-spring suspension package for short- and long-wheelbase applications. The two-leaf parabolic springs...

Self-Locking Nut, 3/8" BSF, used to secure propshaft fasteners within the drivetrain. The deformed thread form provides a self-locking action that...

Blanking Plug for closing an unused 16 mm (5/8") hole in body or trim panelling. A push-in plastic plug used to blank off redundant or open apertu...

Ignition Coil A high-output sports coil for the ignition circuit. It sits between the low-tension supply and the distributor, converting the primar...

Tow Ball 50mm flange-fixing tow ball for use with a bolt-on tow bar drop plate. Rated for a maximum gross trailer weight of 3.5 tonnes, with a D-v...

Antiluce Cotter Pin for the tailgate assembly. This self-locking drop fastener secures the rear door capping fixing, retaining the tailgate hardwa...

Clutch Withdrawal Unit Gasket - seals the mounting joint where the clutch withdrawal (release) housing bolts to the gearbox bellhousing. Part of t...

Flasher Lamp Lens - Sparto Type is the replaceable coloured lens for the Sparto-pattern direction indicator (flasher) lamp, forming part of the ext...

Sealing Ring A rubber O-ring sealing ring serving two separate shaft and tube interfaces. It is used on the transfer box high/low range selector s...

Set Screw - a fully threaded hexagonal-head setscrew with a 3/8" UNC (Unified Coarse) imperial thread and a 7/8" length. Used as a Rover V8 engine-...

Oil Gallery Plug for the cylinder block oil gallery on Land Rover 4-cylinder engines. The oil gallery is the network of internal drillings in the ...

Self-Tapping Screw – No. 6 × 3/4 in used to secure interior trim and panel fixings, such as the dash panel and upper fascia mouldings. Being self-...

Plain Washer A flat washer sized for 1/4" fasteners, used as a general-purpose fixing throughout the body, chassis and mechanical assemblies. It s...

Gear Change Selector Shaft Spring A spring for the gearbox gear-change selector mechanism. It acts on the selector shaft to provide the spring loa...

Oil Filler Pipe Gasket seals the joint between the oil filler pipe and the engine front (timing) cover. Fitted at the filler pipe mounting flange,...

Seat Box End Panel for the left-hand end of the seat box - the structural box that forms the seat base across the centre of the vehicle. This repa...

Plug Washer for the drain and filler/level plugs on the LT95 gearbox and differential. The washer seats between the threaded plug and the casing t...

Battery Retaining Rod secures the battery into its tray. The threaded rod hooks onto the battery tray and draws the hold-down clamp down against t...

Hex Nut with a 5/16" UNF (Unified National Fine) thread. This six-sided fastener threads onto a matching 5/16" UNF bolt or stud and is tightened w...

Transfer Box Output Mud Shield Shield that fits over the transfer box output flange to protect the output shaft oil seal from mud, water and debris...

Bolt - an imperial hexagon-head bolt with a 5/16" UNF thread and a 3-1/4" shank length. This long-shank bolt is used at the alternator mounting on...

Bearing used across several Land Rover drivetrain assemblies: the LT230 transfer box, where it supports the high and low range gear; the LT95 gearb...

Polyurethane Suspension Bush Kit - a full-vehicle set of replacement suspension bushes for the Series 3 long-wheelbase (109") chassis, supplied in ...

Exhaust U-Bolt - a U-bolt clamp used to secure a joint in the exhaust system. It retains the exhaust front pipe (downpipe) connection, clamping th...

Needle Roller Bearing for the transfer box intermediate gear. The bearing carries the intermediate gear on its shaft within the gear cluster, allo...

Filler Strip Spacer for the door top, fitting at the vertical joint of the door-top glass frame. The strip fills and finishes the vertical gap in ...

Nut is a hexagonal nut cut with a 7/16" BSF (British Standard Fine) thread. It threads onto a matching 7/16" BSF bolt or stud to secure a bolted j...

Thin Nut - a reduced-height hex nut with a 5/16" UNF (Unified Fine) thread. The shallow profile suits fastening points with limited clearance and ...

Bolt - M8 x 100mm hex head bolt used in the transmission mounting assembly. Secures transmission mounting components on Series III vehicles equipp...

Bolt - 5/16" UNC x 4-3/4" is a hex bolt that secures the water pump and power steering pump on the Rover V8 engine. It has a 5/16" UNC thread and ...

Choke Spring - the large return spring for the choke swivel on the Zenith carburettor, within the fuel system. It fits over the choke swivel spind...

4-Leaf Parabolic Rear Spring Pair for the rear suspension of Series long-wheelbase Land Rovers. Parabolic leaf springs use a progressive, variable...