Land Rover Series 2 & 3 Parts

Elbow Gasket seals the coolant outlet elbow, or thermostat housing, to the inlet manifold on the V8 petrol engine, forming part of the engine cooli...

Front direction indicator lamp for the vehicle lighting system. This unit provides the flashing directional signal function at the front of the v...

Clutch Cylinder Adaptor - a pipe union that connects the hydraulic clutch supply pipe to the inlet port of the clutch master cylinder. Fitted at t...

Gearbox Plug Sealing Washer for LT76 and LT77 manual gearbox drain, level, and inspection plugs. This sealing washer fits beneath the thread of ge...

Water Pump Inlet Gasket - seals the water pump inlet housing against the engine front cover within the coolant circuit. It forms the joint between...

Plain Nut - 1/4" BSF hexagonal plain nut in the British Standard Fine (BSF) thread form. The BSF thread form uses a finer pitch than BSW (British ...

Accelerator Spring for the throttle linkage on diesel engines. This return spring acts on the accelerator linkage, drawing the throttle back to th...

Oil filler cap

Door Top Seal Strip for the front door assembly. This rubber seal runs along the upper section of the door frame, sealing the gap between the door ...

Brake Pipe - Wheel Cylinder is a rigid hydraulic brake pipe in the front brake circuit, running from the brake backplate to the flexible jump hose....

Oil Seal for the front axle swivel pin housing. Seals the front driveshaft where it passes into the inner end of the swivel housing, retaining axl...

Air Filter Element for the 3.5L V8 Twin Carb petrol engine air intake. This filter element is fitted in the air intake housing ahead of the carbur...

Distributor Rotor Arm for the 3.5L V8 petrol ignition system. The rotor arm sits on top of the distributor shaft beneath the cap and rotates to dis...

Manifold Gasket - inlet to exhaust manifold gasket for the 2.25L 4-cylinder petrol engine. On this engine, the inlet and exhaust manifolds bolt to...

Oil Filter Gasket for the engine lubrication system, sealing the oil filter bowl to the filter housing on 4-cylinder petrol and diesel engines. Th...

Clutch Release Plate for the LT77 5-speed manual gearbox clutch release assembly. This mounting plate fastens the external hydraulic clutch slave ...

Sealing Washer used at sealing interfaces across multiple engine assembly groups. This washer is used in rocker cover and breather assemblies, val...

7" round LED headlamp 12/24V black 78W LHD (pair)

Timing Chain for the Rover V8 petrol engine, part of the camshaft drive assembly located in the front timing cover. This single-row roller chain t...

Cable Clip for securing the body wiring harness, part of the vehicle electrical system. This clip retains a cable run against the body or chassis,...

Bonnet Canvas Rest Strip for the front body assembly. This canvas strip mounts across the top of the radiator/front panel, forming the surface the ...

Wheel Cylinder Overhaul Kit for front drum brake systems fitted with 11-inch brake drums. This kit provides the necessary parts to overhaul all fo...

Oil Seal - a radial oil seal fitted between the wheel hub and stub axle within the wheel hub and drive shaft assembly. The seal retains lubricant ...

Rubber Mat Set for the front footwells - a pair of moulded rubber floor mats covering the driver and passenger sides of the cab floor. The mats ar...

Door Hinge for the rear end (load/tail) door, lower position. One of the pair of side-hinged door hinges that mount the rear door to the body aper...

Hinge Pin Kit containing the replacement hardware for door and rear tailgate hinges on Series and early Defender models. Fits the front and rear d...

CuNiFer Brake Pipe, 3/16" outer diameter, supplied for the brake hydraulic circuit. The copper-nickel alloy resists corrosion and is soft enough to...

Distributor Cap for the ignition distributor on the V8 EFI engine. The cap seats over the distributor and carries the high-tension current from th...

Wiper Drum Adaptor - splined adaptor used in the windscreen wiper system to connect the wiper arm to the splined wiper spindle. The adaptor seats ...

Side Cover Gasket sealing the cylinder-block side cover (tappet inspection cover) to the block face, for petrol and diesel engines. The side cover...

Enhance the ignition performance of your Land Rover Defender, Discovery 1, and Range Rover Classic (3.5 V8 carb & EFI models) with this high-qu...

Toggle Switch is a two-position on/off switch in the dashboard switchgear, controlling the instrument and panel lighting circuit. The sprung toggl...

Lock Barrel & Key Set for the door locks. This set contains two lock barrels and two keys, supplied without a steering column lock. For the an...

Oil Pump Gasket for the Rover V8 petrol engine lubrication system. This gasket seals the oil pump to its mating face, maintaining oil pressure and...

Axle Pinion Gasket for the Salisbury rear axle, sealing the pinion bearing retainer to the differential housing at the propshaft flange end of the ...

Rocker cover rubber washer petrol

Sliding Window Seal for the front door assembly. This rubber seal fits to the front face of the sliding side window, sealing the glass against the ...

Lights and Heater Toggle Switch - a three-position Lucas-type toggle switch fitted to the dashboard switchgear. It acts as the master control for t...

Fuel Filter for the diesel fuel delivery system, separating dirt, debris and water from the fuel before it reaches the injection pump. Fitted in t...

Air Intake Hose for the 2.25 litre diesel engine, forming part of the air induction system between the air cleaner and the intake manifold. It car...

Fuel Filler Cap Seal is the sealing ring fitted inside the metal fuel filler cap. It forms the seal between the cap and the filler neck, preventin...

Wheel Cylinder for the rear drum brake assembly, left-hand side. The wheel cylinder forms part of the hydraulic drum brake circuit, converting hyd...

Wiper Motor for the windscreen wiper assembly. It converts the electrical supply into rotary motion, driving the wiper transmission and linkage th...

Propshaft Bolt Kit - Rear is a driveline fixing set for securing the rear propeller shaft at its flange connections. The kit provides the correct-...

Lock Nut - 7/16" UNF - self-locking nut providing a prevailing-torque fastening. The nut resists loosening under vibration and dynamic load, secur...

Rear Drum Brake Shoe Set covering one full axle, sized for 11-inch rear drum brakes. The shoes carry the friction linings that press outward agains...

Glass Run Channel for the door window aperture, supplied in a 2 m length. The channel lines the door frame to guide and seat the side window glass...

Rear Drum Brake Shoe Set covering one full axle, sized for 11-inch rear drum brakes. The shoes carry the friction linings that press outward agains...