Land Rover Series Parts

Bonnet Hinge Bush for the Land Rover bonnet hinge assembly. This bush fits into the bore of the bonnet hinge, providing a wear surface around the ...

Drive Flange Joint Washer is the sealing washer installed at the joint between the drive flange and the stub axle, preventing differential oil from...

Outer Hub Lock Washer for the front and rear hub assembly on Land Rover solid axles. This lock washer secures the hub bearing retaining nut agains...

Swivel Housing Grease for the front axle swivel assembly, supplied as a single pre-measured one-shot sachet. The sachet delivers the correct charg...

Sump Gasket - 4-Cyl for the engine sump sealing joint on Land Rover 4-cylinder engines. This gasket seals the mating face between the sump pan and...

Side Lamp - front side (parking) lamp in the exterior lighting system. Dome-type front side lamp providing position and marker lighting at the fro...

Rear Light Lens for the rear stop and tail lamp. The red lens fits over the lamp body to cover the stop and tail bulb, transmitting the brake ligh...

Clutch Slave Cylinder is the hydraulic actuator in the clutch release circuit, mounted externally on the gearbox bellhousing. When the clutch peda...

Brake Drum Screw for the brake drum assembly. This retainer screw secures the brake drum to the wheel hub flange, preventing the drum from displac...

Hub Cap fits over the end of the front or rear hub, enclosing the drive flange and hub assembly. It closes off the outer end of the hub to retain ...

Propshaft Bolt - a fastener that secures the propshaft universal-joint flange to the differential drive flange within the driveline. It clamps the...

Propshaft Gaiter with Clips for the front propshaft sliding joint. This rubber gaiter fits over the splined sliding joint (slip yoke) of the front...

Indicator Lamp Lens, amber, for the round-type direction indicator (turn signal) lamp. The lens fits over the lamp body to seal and protect the bul...

Door Mirror supplied as a complete unit comprising the mirror head and its mounting arm, for external door mounting to give rearward visibility fro...

Oil Filter for the engine lubrication system of the 2.25L four-cylinder petrol and diesel engine. The filter traps combustion by-products, metal p...

Crankshaft Spigot Bush is the clutch pilot bush that presses into the rear face of the crankshaft, between the engine and the clutch. It supports ...

Sump Plug Sealing Washer for the engine lubrication system. It seats between the oil drain plug and the sump pan boss, sealing the joint so the plu...

Thermostat Housing Gasket in the engine cooling system. This gasket seals the thermostat housing to its mating surface on the engine, preventing c...

Thermostat Housing Gasket for the engine cooling system. This top gasket seals the joint between the thermostat housing and the engine, preventing...

Number Plate Lamp for the rear number plate lighting circuit. This complete lamp assembly mounts at the rear of the vehicle to illuminate the numb...

Fan Belt for the engine auxiliary (accessory) drive. Transmits drive from the crankshaft pulley to the water pump, cooling fan and dynamo or altern...

Engine Mounting is a rubber-to-metal anti-vibration mount in the engine mounting assembly, supporting the petrol engine on the chassis frame. The ...

Manifold Gasket for the 2.25L and 2.5L 4-cylinder petrol engines. This gasket seals the combined inlet and exhaust manifold assembly to the cylind...

Floor Panel Screw with a mushroom head profile, used to secure floor plates and lower rear body panel assemblies on the Defender. The low-profile ...

Hub Nut Spanner for the front hub and wheel bearing assembly. The 52mm tool engages the hub retaining nut on the front stub axle. Designed for use...

Oil Filter for Land Rover petrol and diesel engines, part of the engine lubrication circuit. This screw-on canister filter threads onto the filter...

Radiator Cap seals the radiator filler neck and maintains the engine cooling circuit at its rated pressure. Rated at 9 lb (0.62 bar), the spring-l...

Headlamp for the front lighting system: a 7-inch round unit with a flat glass lens. The lamp takes a replaceable H4 halogen bulb, giving combined ...

Sump Gasket for the Rover V8 petrol engine oil sump assembly. This gasket is fitted between the oil sump (oil pan) and the engine block, forming a...

Dash Ventilator Bulkhead Seal for the fresh air intake assembly. Fitted between the dash ventilator panel and the bulkhead, the seal forms an air-...

Brake & Clutch Pedal Pad for the foot pedal assembly. This moulded rubber pad fits over the brake and clutch pedal arm, providing the grip surf...

Engine Mounting is a rubber-to-metal anti-vibration mount in the engine mounting assembly, supporting the 2.25L diesel engine on the chassis frame....

Hex Nut - 5/16" UNF is a plain hexagonal nut with a 5/16 inch UNF thread, used as a general-purpose imperial-thread fastener throughout the chassis...

Front Hub Nut for the front hub and driveshaft assembly, retaining the wheel hub and bearing assembly on the stub axle. This large-diameter locknu...

Side Lamp Lens - Front - Clear is the replaceable lens for the front side and indicator lamp within the exterior lighting assembly. The clear lens...

Rear Reflector mounts in the rear lamp area as part of the rear lighting and signalling assembly. A passive retroreflector that returns incident l...

Fuel Filter for the diesel fuel delivery system, separating dirt, debris and water from the fuel before it reaches the injection pump. Fitted in t...

Door Hinge Shim for the Land Rover door hinge assembly. This 1mm shim is fitted between the door hinge and its mounting face to set or adjust the ...

HT Ignition Lead Set for the 2.25L and 2.5L 4-cylinder petrol ignition system. This set of four high tension leads connects the distributor to eac...

Clutch Release Staple is the spring retaining clip that secures the clutch release bearing assembly to the clutch fork, holding the bearing in posi...

Front cover oil seal

Tap screw

Transfer Box Sealing Washer for gearbox and transfer box drain and filler plugs. This sealing washer fits beneath the drain or filler plug thread,...

Glass Fuse - 35A cartridge fuse for the electrical system. A glass-bodied fuse rated at 35A that protects a wiring circuit against overcurrent; th...

Wiper Blade for the front windscreen, with a stainless steel frame. The blade clears the driver's field of view across the front windscreen. It at...

Wheel Cylinder for the drum brake assembly - the left-hand hydraulic slave cylinder that operates the brake shoes. The same cylinder serves either ...

Oil Pressure Switch for the engine lubrication system warning circuit. This pressure-sensitive switch threads into the engine block oil gallery an...

Fuel Tank Sender Locking Ring for the fuel tank sender unit assembly. This ring secures the fuel level sender unit in position within the fuel tan...