Land Rover Series Parts

Water Pump Gasket - 7-Hole for the cooling system on Land Rover 4-cylinder military engines. This gasket seals the mating face between the water p...

Pipe seal

Jubilee Clip - 21-44mm is a worm-drive hose clip with a 21-44mm clamping range. The band is tightened by a captive worm screw to clamp small- to m...

Locknut for body and trim panel fixings. It seats into a pre-formed aperture in the panel to provide a captive threaded point for the screws or bo...

Shakeproof Washer – a serrated, externally toothed lock washer used at the clutch hydraulic hose union. The teeth bite into both the mating surfac...

Fuel Pipe Olive for the fuel supply line. The olive is the compression ferrule that seats between the fuel pipe and its union fitting. When the un...

Gearbox Thrust Washer for the intermediate gear (laygear) in the main gearbox, used on 4-cylinder applications. It locates against the intermediat...

Bolt - an imperial hexagon-head bolt with a 5/16" UNF thread and a 3-1/4" shank length. This long-shank bolt is used at the alternator mounting on...

double washer, restrictor

Rivet is a permanent mechanical fastener used in the lower tailboard (drop-down tailgate) hinge assembly. Set through the hinge components, it for...

Blanking Plug for closing an unused 13 mm (1/2") hole in body or trim panelling. A push-in plastic plug used to blank off redundant or open apertu...

Oil Pump Sealing Washer, part of the engine lubrication circuit at the oil pump. The washer forms a static seal at the oil pump joint, preventing ...

Set Screw - a fully threaded hexagonal-head setscrew with a 3/8" UNC (Unified Coarse) imperial thread and a 7/8" length. Used as a Rover V8 engine-...

Bolt - a hexagonal-head bolt with a 5/16" UNC (Unified Coarse) imperial thread and a 3/4" length. Used as an engine-assembly fixing, including cams...

Brake Shoe Screw - a retaining screw within the drum brake assembly that secures the brake shoe in position. It holds the shoe located against the...

Washer A copper joint sealing washer for the oil filter housing, part of the engine lubrication system. It seals the oil plug or the oil filter ad...

Exhaust manifold stud

Lock Washer secures the retaining hardware on the layshaft (countershaft) within the manual gearbox. A tab on the washer is folded against the ret...

Screw – a black self-tapping screw with a pan head and Pozidriv drive recess, size No. 10 × 5/8 in, used to secure body, trim and panel fixings. B...

Headlamp Screw is a fastener used in the front headlamp assembly. It secures the headlamp unit and rim within their mounting, holding the lamp in ...

Main Bearing Cap Bolt - a 1/2" UNC bolt that fastens a main bearing cap to the cylinder block on the Rover V8 engine. It clamps the main bearing c...

Core Plug - Cylinder Head A 7/8" diameter core plug (welch/expansion plug) that seals a casting core hole in the cylinder head. It closes the open...

Set Screw - a fully threaded hexagonal-head setscrew with an M10 metric thread and a 20 mm length. A general-purpose fixing used at fastening point...

Circlip for the handbrake (parking brake) linkage. This external retaining circlip secures the handbrake relay elbow onto its pivot post, holding t...

Plate

Flywheel Dowel is a locating dowel that registers the flywheel to the crankshaft rear flange. Pressed into the crankshaft flange, it sets the angu...

Shock Absorber Washer Retaining washer for the rear shock absorber lower mounting. Part of the rear suspension assembly, it locates over the lower...

Nutsert - 5/16" UNF is a blind rivet nut (rivnut) with a 5/16" UNF internal thread. A nutsert is installed into a pre-drilled hole in sheet metal ...

Manifold Stud - a mounting stud that secures the exhaust manifold to the cylinder head. It threads into the cylinder-head casting and projects thr...

Cab Mounting Stud

Engine Stud for the Rover V8 petrol engine, measuring 5/16" x 2-1/8" with a UNC/UNF dual thread form. The coarse UNC end threads into the engine c...

Sealing Washer is a copper joint washer used in multiple engine and ancillary applications across the Land Rover range, including as a sealing wash...

Hose Clip for securing flexible hoses to pipes and stubs throughout the Land Rover. Tightening the clip compresses the hose onto the stub to form a...

Gear Lever Retaining Plate for the gear lever turret on the LT76 manual gearbox. The plate bolts over the base of the gear lever to retain it in i...

Clip - 13/64" x 3/8" is a single-bolt retaining clip used to secure wiring harnesses, vacuum lines, and small-bore hoses to body or engine bay brac...

Filler and Level Plug for the V8 4-speed gearbox and for differential assemblies across a wide range of classic Land Rover models. Fitted at the s...

Mainshaft Nut - castellated nut that retains the assembled components on the rear of the gearbox mainshaft. The castellations accept a split pin to...

Crankshaft Oil Seal - Rear seals the rear of the crankshaft where it leaves the cylinder block at the flywheel end, retaining oil within the bottom...

Rocker Cover Screw for the Rover V8 petrol engine. This 1/4" UNC screw secures the valve (rocker) cover to the cylinder head. The rocker cover per...

P-Clip - 19/64" x 3/8" is a pressed-steel P-profile retaining clip used to route and secure fuel lines, brake pipes, or wiring looms against a chas...

Rubber Washer - Seat Backrest for Land Rover Series and Defender models. This rubber washer is used in the seat backrest assembly, fitting beneath...

Shakeproof Starlock Washer used within the clutch master cylinder and pipe assembly. The washer pushes onto a plain shaft or pin and grips it with...

Flywheel Bolt, 7/16" UNC x 1" hexagonal head, securing the flywheel to the rear crankshaft flange. Used on V8 petrol engines with manual transmiss...

Handbrake Carrier Spacer for the handbrake assembly on Series II, IIA, III and Defender 90/110. This spacer fits within the handbrake carrier mech...

Conrod

Bolt used in the camshaft assembly of the 3.5L V8 petrol engine. Imperial UNF fastener, 7/16" diameter with a shank length of 1 1/8". Supplied as ...

Inner Ring

Stud for the carburettor-to-inlet-manifold joint. Threaded stud that secures the carburettor onto the inlet manifold flange. It provides the fixin...