Land Rover Series Parts

Flywheel Bolt, 7/16" UNC x 1" hexagonal head, securing the flywheel to the rear crankshaft flange. Used on V8 petrol engines with manual transmiss...

Rectifier Alt Acr

Piston ring set petrol 2,25 020 Mahle (per zuiger)

Rear Fog Lamp forming part of the rear lighting assembly, providing a high-intensity red rear light for use in poor visibility. It operates on its...

Handbrake Carrier Spacer for the handbrake assembly on Series II, IIA, III and Defender 90/110. This spacer fits within the handbrake carrier mech...

Handbrake Gaiter for the handbrake lever assembly in Series II, IIA, and III Land Rovers. Fits 109-inch wheelbase V8-engined variants. The gaiter ...

Synchro Cone (Baulk Ring) - LT95 4-Speed Gearbox This synchro cone, also known as a baulk ring, is a component of the synchroniser assembly within...

Oil Seal Retainer for the front axle. It retains the oil seal at the swivel pin bearing housing, holding the seal that runs against the halfshaft.

Differential Pinion Bearing Shim - 0.070 in, for use in the Rover 10-spline rear differential. This shim sets the preload on the pinion outer beari...

Flywheel - 5-Bearing is the rotating mass mounted to the rear flange of the crankshaft in the 5-main-bearing variant of the 2.25L and 2.5L 4-cylind...

Conrod

Radiator Hose - the top hose of the engine cooling circuit, connecting the cylinder head outlet to the top of the radiator. It carries heated cool...

Bottle Cap for the coolant expansion bottle. Seals the coolant expansion reservoir and maintains system pressure within the cooling circuit.

Bolt used in the camshaft assembly of the 3.5L V8 petrol engine. Imperial UNF fastener, 7/16" diameter with a shank length of 1 1/8". Supplied as ...

Primary Pinion Bearing Shim sets the installed position of the primary pinion within the LT95 four-speed gearbox casing. 2.05 mm thick, it control...

Inner Ring

Stud for the carburettor-to-inlet-manifold joint. Threaded stud that secures the carburettor onto the inlet manifold flange. It provides the fixin...

Heater Control Pin

Flywheel assy

Temperature Sensor Adaptor - UNF-threaded adaptor for the water temperature transmitter. Screws into the engine coolant passage to accept the temp...

rod control GENUINE LR - 2.25 petrol and 2.6 petrol, 1968 onwards

Accelerator Rod in the throttle linkage. This rigid rod transmits accelerator pedal movement through the linkage to operate the engine throttle.

Bush - Low Gear Wheel is a gearbox internal bush fitted to the low gear wheel in the Series 2 and Series 3 manual gearbox on 109-inch 1-ton Land Ro...

Slip Ring for the horn contact in the steering column. This contact ring maintains the electrical connection to the horn as the steering wheel tur...

Washer - Diesel Sedimentor is a sealing washer used in the diesel fuel sedimentor (fuel filter/water separator) assembly on diesel-engined Land Rov...

Screw - a threaded fastener used to join or secure components.

Harness Bracket Shim for the wiring harness mounting hardware. Fitted behind the harness support bracket at its mounting point, the shim sets the ...

Door Latch Shim - Rear - a packing shim for the rear door anti-burst latch, part of the door lock and handle assembly. Fitted behind the latch on ...

Fuel Tank Mounting Washer is used at the fuel tank mounting points, spreading the clamping load of the fixing across the mounting bracket or strap....

Grille Spring Clip for securing the front grille panel on Series III models. Fitted at the grille mounting points, this spring clip retains the fro...

Heater Control Mounting Plate for left-hand drive applications. Fitted within the heater control assembly in the cab interior, this plate provides ...

Washer

Top cover

Brush kit RTC830 fits: Rover 3.5L V8 startermotor type 3M100 - S3 109" stage 1 V8 - 101" Forward Control - Range Rover Classic

Water Pump Casing for the engine cooling circuit, the housing that carries the coolant pump and directs flow into the cylinder block. The casing l...

Diesel Fuel Filter Plug Seal - a sealing ring for the drain plug on the diesel fuel filter and sedimentor. It seals the drain/bleed plug against t...

Bolt, a threaded fastener used on the 2.0L petrol engine.

Bolt is a hex-head threaded fastener used to secure components at bolted joints, such as engine and starter-motor mountings.

Layshaft Bearing Distance Piece Spacer for the layshaft (cluster gear) bearing within the main gearbox. It locates against the layshaft bearing to...

Clip - a retaining clip within the vehicle body hardware, used to secure and locate a fitted component in position.

Gearbox Selector Circlip - a retaining circlip within the manual transmission gear selector mechanism. The circlip locates on its shaft to secure ...

Exhaust Valve Guide for the 2.6L six-cylinder petrol engine. The guide is pressed into the cylinder head and locates the exhaust valve stem, holdin...

Crankshaft Spigot Bush is the clutch pilot bush that presses into the rear face of the crankshaft, between the engine and the clutch. It supports ...

PTO Selector Cover Plate - a blanking plate for the power take-off (PTO) selector aperture on the transfer box. It covers and seals the selector o...

Brake Lining - Rear is a replacement friction lining for the rear drum brake assembly on long-wheelbase Land Rover models, covering 109-inch, 110-i...

Reverse Gate Bracket is the fixed section of the reverse-gate stop within the gear-lever mounting on the Series four-speed gearbox. It forms the g...

Seat Base Corner Capping in plastic. Fitted at the outer corners of the front seat base frame, this capping provides a neat finished edge and prote...