Land Rover Series Parts

Plug

Rear Absorber Shock

Elbow Gasket seals the coolant outlet elbow, or thermostat housing, to the inlet manifold on the V8 petrol engine, forming part of the engine cooli...

Viscous Fan Coupling is the temperature-controlled drive unit between the water pump and the engine cooling fan. It mounts on the water pump shaft...

Front Door Glass Guide is a moulded plastic guide that locates the front door drop glass within its window channel. Fitted inside the door frame, ...

Inline Fuel Filter for petrol engines, fitted in the low-pressure fuel supply line between the tank and the fuel pump or carburettor. This sealed ...

Air Filter Element for the 3.5L V8 Twin Carb petrol engine air intake. This filter element is fitted in the air intake housing ahead of the carbur...

Drive Flange Joint Washer is the sealing washer installed at the joint between the drive flange and the stub axle, preventing differential oil from...

Copper Sealing Washer - a general-purpose copper crush washer used to seal threaded joints, plugs and unions. The soft copper deforms as the fitti...

Tow Ball & Pin is a towing coupling component that mounts to the tow bracket or drop plate. The ball provides the coupling point onto which a ...

Shock absorber rear early style, two halve bushes in upper eye, fitted to bracket using a large washer and a split pin.

Core Plug for the rear of the camshaft bore in the V8 petrol cylinder block. The cup-type plug seals the machined opening at the rear of the camsh...

Engine Mounting Rubber (V8) supports the V8 petrol engine on the chassis and isolates its vibration from the bodyshell. The bonded rubber-to-metal...

Absorber Shock

Connecting Rod Bearing Set - a set of big-end bearing shells for the Rover V8 petrol engine. The connecting rod bearings are the split shell beari...

Battery - Wet Non-Spillable - sealed lead-acid starting and deep-cycle battery with dual terminals. Rated at 68 Ah with 1500 cranking amps. The pl...

Bolt

Low Note Horn, a 335 Hz electric horn within the audible warning circuit. Produces the low-frequency tone of a dual-tone horn arrangement, pairing...

Wheel Wrench a 27mm wheel brace for loosening and tightening wheel nuts. The 27mm socket end matches the wheel nuts fitted to the applicable vehic...

Emergency Bulb and Fuse Kit - 12 volt, for vehicles using H4 headlamp bulbs. A compact set of replacement bulbs and fuses to carry in the vehicle,...

Towing Bracket Slider Lock Pin is the pin that locks the vertical slider of a Dixon Bate adjustable-height towing bracket at the selected height. ...

Coolant Temperature Sensor - V8 EFI for the engine management system. This sensor monitors coolant temperature and sends a continuous signal to th...

Front Door Glass Guide is a moulded plastic guide that locates the front door drop glass within its window channel. Fitted inside the door frame, ...

H3 Halogen Bulb, 55W, single-filament. The H3 is a single-filament halogen capsule with a flying-lead connector, used in auxiliary lighting units ...

Sump Gasket for the Rover V8 petrol engine oil sump assembly. This gasket is fitted between the oil sump (oil pan) and the engine block, forming a...

Transmission Brake Dust Cover for the central handbrake drum on the transmission output shaft. This cover shields the handbrake drum and brake sho...

Stop/Tail Bulb - 12V 21W - Twin Pack (trade reference 380). This pack contains two BAY15d dual-filament bayonet bulbs rated 12V 5/21W, suitable fo...

Brake Union - Blanking Plug, male thread, M10 x 1mm, short body. Used in the metric hydraulic brake circuit to blank off an unused or redundant po...

Valve Spring for the cylinder head valvetrain. Fitted over the valve stem, it holds the valve closed against its seat and keeps the follower in con...

Differential Gear Kit is a set of differential gears for the Rover-type axle differential, in the 10-spline configuration. The differential gears ...

Differential Cover is the pressed plate that closes the differential aperture in the axle casing, retaining the axle oil and giving access to the c...

Bolt - a flanged-head bolt used as a general fastener across a range of engine, chassis and body locations, including the timing cover, chassis fra...

Oil pump relief valve washer V8

Valve Spring - V8 is a cylinder head valve spring for the Rover 3.5L and 3.9L V8 petrol engine. The valve spring seats between the cylinder head a...

Valve Cotter (split collet) for the Rover V8 petrol engine valve train. Locks the valve spring retainer to the valve stem, holding the spring unde...

Camshaft Retaining Plate for the four-cylinder engine. Bolted to the front face of the cylinder block behind the camshaft gear, it locates the cams...

Carburettor Conversion Kit - replaces the twin Stromberg or SU carburettor setup on the Rover V8 with a single four-barrel carburettor mounted on a...

Tow Hitch Locking Pin (R-Clip) is the spring-steel retaining clip that secures the tow pin in an adjustable tow hitch. It pushes through the hole i...

Towing Bracket Slider Lock Pin is the pin that locks the vertical slider of a Dixon Bate adjustable-height towing bracket at the selected height. ...

Towing Hitch Pin is the 25mm locking pin for the Dixon Bate 3.5 tonne ball, jaw and pin hitch (DA2123 / RTC8159), retaining the coupling jaw closed...

Shock Absorber Boots are protective covers that fit over the shock absorber body to shield the shaft and seal from mud, grit and debris. Supplied ...

Waterproofing Kit - V8 seals the ignition system of the V8 petrol engine against water and damp. The kit waterproofs the distributor and ignition ...

Thermostat Kit for Electric Fan Kenlowe

Fitting Kit for Pacet Fan