Land Rover Series Parts

Rocker Bracket Locating Dowel for the cylinder head and rocker assembly in the 2.25L and 2.5L petrol and diesel engines. This dowel locates the ro...

Carburettor Bell Crank Bush for the accelerator throttle linkage on the 2.25L 4-cylinder petrol engine. The bush locates the throttle bell crank a...

Front leaf spring LWB diesel DS

Leaf Spring - Front - 11-Leaf A semi-elliptic front leaf spring built up from an eleven-leaf pack, part of the front suspension. It carries the ch...

Bolt - 5/16" UNF x 5/8" is a general-purpose hexagon-head set bolt in 5/16 UNF (Unified National Fine) thread, 5/8 inch in length. Used across engi...

Manifold Stud is used to secure the combined inlet/exhaust manifold assembly to the cylinder block on Series vehicles fitted with the 2.25L diesel ...

Timing Chain Tensioner Spring for Land Rover 2.0L Diesel and 2.25L Petrol and Diesel four-cylinder engines. This spring applies constant pressure ...

Sealing Ring - Rocker Cover Breather Bolt for the 2.25-litre 4-cylinder engine. This sealing ring is fitted under the rocker cover breather bolt, ...

Stud for use in Land Rover gearbox assembly.

Mainshaft Bearing for the gearbox mainshaft - the centre bearing that supports the mainshaft within the gearbox casing. It locates and carries the...

Wiper Motor Mounting Pad for the rear wiper motor, used on the Defender and Range Rover Classic. This rubber fixing pad sits between the wiper mot...

Mainshaft Thrust Washer - 2nd Gear (0.125") is a selective shim located within the Series gearbox, fitted to control axial play on the second gear ...

Felt Seal for the clutch and brake pedal shaft, fitted in the pedal box where the cross-shaft passes through the housing. The felt washer seats ar...

Overdrive Needle Bearing for the front of the mainshaft in a Fairey overdrive unit. The bearing supports the overdrive clutch sleeve on the mainsh...

Screw: pan head self-tapping screw.

Hook & Loop Fastening Strap for securing and bundling loose items within the vehicle interior, cargo area, or workshop. The strap wraps around ...

Crankshaft Front Key locates and locks the timing sprocket or front pulley hub to the crankshaft snout, preventing rotational slip between the cran...

Transfer Box to Gearbox Mounting Stud, 2" length, used to fasten the transfer case to the rear of the main gearbox casing. This stud forms part of...

Light Socket for the inspection lamp on Series Land Rover vehicles. This black bayonet-type bulb holder is used in the inspection lamp assembly, p...

Swivel Pin Seat Cone for the front axle swivel housing. This cone provides the precision seating surface on which the swivel pin locates within th...

Screw - 2BA x 1" is a round head screw in British Association (BA) thread form, 2BA size, 1 inch in length. Used throughout the Series Land Rover ...

Exhaust Silencer for right-hand-drive applications, constructed in stainless steel. Part of the exhaust system, this silencer attenuates combustio...

Crown Wheel & Pinion Set - the final-drive gear pair housed within the axle differential. The pinion takes drive from the propshaft and turns t...

Set Screw - Water Pump Spindle is a locking fastener that locates the water pump spindle within the water pump housing on Series engines produced b...

Anti-Roll Bar Link & Shock Bush Kit renews the compliant mounting bushes in the anti-roll bar link and shock absorber mounting points within th...

Bolt - 1/2 UNF x 1 is a hexagon-head set bolt in 1/2 UNF (Unified National Fine) thread, 1 inch in length, used to secure the engine mounting brack...

Differential Crown Wheel Locking Tab is a tab washer used in the axle differential assembly to lock and retain the crown wheel bolts after tighteni...

Fuel Filler Screw is a 2BA x 3/8" fastener used to secure the fuel filler fitting. It retains the fuel filler to the body panel; the companion nut...

Braided Earth Strap with Battery Clamp - 300mm for the vehicle electrical grounding circuit. This braided copper earth strap is fitted with an int...

Distance Piece for the LT76 gearbox mainshaft. This spacer maintains the correct axial position of components along the mainshaft within the LT76 ...

Inner Tube for 7.50 x 16 and 7.00 x 16 tyres, fitted inside the tyre on tube-type wheels to hold the air pressure. Supplied with a small diameter ...

Front Door Seal Kit re-seals the right-hand front door aperture, supplied with the rivets needed to fit it. The kit contains six door sealing rubb...

Footwell Repair Panel for the left-hand (nearside) footwell - a body repair section covering the footwell floor and inner side panel. For right-han...

Fluid Reservoir for the hydraulic braking and clutch system on the early Land Rover Series I. This metal reservoir feeds the Girling master cylinde...

Front Halfshaft Bearing - roller bearing supporting the inner end of the front halfshaft within the front axle housing. Located at the inboard end...

Differential Bearing for the Rover-type axle, part of the differential carrier assembly inside the axle case. It supports the differential carrier...

Standard 2nd Row Seat - Square Back & Base - Black Vinyl Fits S2, S3, Classic Defender. Set of 1 seat and 1 back. Made to order, lead time up ...

Rear Door Seal - rubber weatherseal for the rear door aperture. This rubber seal fits around the rear door opening, sealing the closed door agains...

Series 3 Engine Harness. 2.25 Litre 4-cylinder petrol and 2.6 Litre 6-cylinder petrol with Choke Thermostat Warning Switch

Universal Joint for the propeller shaft, measuring 75 mm across the bearing caps with a 27 mm cap diameter. The universal joint is the cross-and-b...

Universal Joint for the propeller shaft, measuring 82 mm across the bearing caps with a 27 mm cap diameter. The universal joint is the cross-and-b...

Wheel Bearing Kit - Metric - Per Wheel