Land Rover Series Parts

Rocker Cover Gasket (Top) - seals the rocker cover joint on the 2.6L 6-cylinder petrol engine. Fitted between the rocker cover and the cylinder he...

Glazing Rubber Strip - rubber glazing section supplied by the metre. It beds and seals a fixed glass panel into its body aperture, locating the gla...

Steering Wheel Boss in the steering column assembly, providing the mounting interface between the column shaft and the steering wheel. The 48-spli...

Ball Bearing for the transfer box, supporting the output shaft and its output flange. Fitted in the LT230 and NV225 transfer boxes, the bearing lo...

Fan Belt for the engine auxiliary (accessory) drive. Transmits drive from the crankshaft pulley to the water pump, cooling fan and dynamo or altern...

Track Rod End for the steering linkage, with a left-hand thread and a fully threaded shank. The track rod end forms the ball-jointed connection be...

HT Ignition Lead Set for the 2.25L and 2.5L 4-cylinder petrol ignition system. This set of four high tension leads connects the distributor to eac...

Plain Washer - imperial-dimensioned flat washer with an internal diameter of 7/16 inch and an outer diameter of 13/16 inch. Used in general fasten...

Hex-head bolt, 3/8" UNC thread, 3/4" long. Unified Coarse (UNC) thread form with a hexagonal head for use with standard imperial spanners and sock...

Hex-head bolt, 5/16" UNF thread, 3/4" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and socke...

Contact Set for the ignition distributor of the 3.5L V8 petrol engine. The contact breaker points open and close the primary circuit to the ignitio...

Glass Fuse rated at 5A, a cartridge-type fuse used in the vehicle electrical system. The fuse seats in the fuse box or an inline fuse holder and p...

T-Piece is a three-way connector in the windscreen washer fluid circuit. It joins the washer hose into two branches, distributing fluid from the p...

Door Bottom Seal for the front door. This rubber seal fits along the lower edge of the door, closing the gap between the door bottom and the body t...

Brake Pipe Union - a female threaded union nut for the brake hydraulic pipework, with a 7/16"-20 UNF thread sized for 1/4" brake pipe. It fastens ...

Flywheel Bolt securing the flywheel to the rear flange of the crankshaft. Used on four-cylinder petrol and diesel engines, including the 200TDi an...

Bolt 1/4" UNF x 2" is a hex-head set bolt with a 1/4-inch Unified National Fine (UNF) thread at 28 threads per inch and a 2-inch shank length. It ...

Output Shaft Oil Seal seals the output shaft of the LT95 four-speed gearbox and integral transfer box, retaining gear oil where the shaft passes th...

Gasket for the front cover of the LT67 gearbox. Seals the front cover plate against the front face of the gearbox housing, preventing transmission...

Gasket for the carburettor-to-inlet-manifold joint in the induction system of the 2.25L 4-cylinder petrol engine. The gasket fits between the carb...

Differential Pinion Inner Taper Roller Bearing used in the differential pinion shaft assembly within the axle final drive. The bearing supports th...

O-Ring for the engine sump, part of the engine lubrication sealing arrangement. Seals the sump joint to prevent oil leakage. Fitted to four-cylind...

Exterior Door Handle with Lock Barrel and Keys, left-hand (nearside). The complete locking handle for the front door, comprising the external push...

Seat Squab Bolt - shouldered bolt for mounting the seat squab (backrest) to its frame. This shouldered bolt secures the seat squab at its mounting...

Mud Shield for the differential pinion. This pressed shield fits over the differential drive flange, ahead of the pinion oil seal, protecting the ...

Oil Seal for the swivel pin housing on the front axle, sealing against the polished surface of the swivel ball. The seal seats in the rear face of...

Brake Cleaner & Degreaser - an acetone-free aerosol solvent cleaner for brake components and general parts cleaning. It removes dirt, grease, ...

Bonnet Buffer is a resilient rubber cushion that forms part of the bonnet closure assembly at the front of the body. It provides the stop the bonn...

Camshaft Cover Gasket seals the camshaft cover plate to the cylinder block, forming part of the camshaft housing and engine lubrication boundary. ...

Headlamp Bezel - black finish. The trim ring that surrounds the 7" round headlamp, retaining the lamp unit in the front panel and finishing the hea...

Spark Plug - ignites the air/fuel mixture in the combustion chamber of the petrol engine. It threads into the cylinder head with its electrode gap ...

Wheel Nut securing a road wheel to the hub, clamping the wheel against the hub mounting face. M16 internal thread and steel construction, to the s...

Hub Bearing – inner taper roller bearing for the front and rear wheel hubs. The bearing sits inside the hub and runs on the stub axle, carrying th...

Exhaust Valve Guide is pressed into the cylinder head to support and align the exhaust valve. It locates the valve stem so the valve seats squarel...

Crankshaft Thrust Washer Pair for the 4-cylinder engine, including the 200 TDi and 300 TDi diesels. The thrust washers sit either side of the centr...

Differential Carrier Bearing is a taper roller bearing that supports the differential carrier within the axle, as part of the crownwheel and pinion...

Brake Pipe Clip secures and routes rigid brake pipes along the chassis within the braking system, holding them in position and guarding against cha...

Exhaust Pipe Clamp

Bolt - threaded fastener with a 7/16" UNF (Unified National Fine) thread and a 2-1/4" length.

Seat Belt Buckle Catch - left-hand front seat belt stalk receiver forming the fixed lower end of the front LH seat belt assembly. The non-audible c...

Exhaust Manifold Stud secures the manifold to the cylinder head on the 4-cylinder engine. It threads into the head and carries the manifold flange...

Heater Control Valve regulates the flow of engine coolant into the heater matrix, forming part of the cabin HVAC heating circuit. The valve is cab...

Inlet manifold stud

Ignition Coil for the V8 petrol ignition system. It converts the low-voltage supply into the high-tension voltage that fires the spark plugs throug...

Screw with a mushroom head and a 1/4" Acme thread, 1" long, with a sherardized zinc finish. Used as a floor fixing, securing the transfer lever ga...

Staple Clamp for the soft top canvas hood, part of the rear body tie-down hardware. Fixed to the rear body side, it forms the anchor loop that the...

Interior Door Lock Button, right-hand, of the interior door furniture. The thumbscrew-type lock button that operates the door lock from inside the...

Interior Mirror Bracket mounts the interior rear-view mirror to the body, providing the fixing point for the mirror stem. This is the untrimmed ve...