Land Rover Series Parts

Exhaust Downpipe for the left-hand front section of the V8 petrol exhaust system. This pipe connects the left-hand exhaust manifold outlet to the ...

Starter Motor for the 2.5L 4-cylinder diesel engine, part of the engine electrical starting circuit. When the ignition is operated the solenoid th...

Inner Sill is a structural body panel forming the inner section of the sill assembly beneath the door aperture, running along the lower edge of the...

Inner Sill is a structural body panel forming the inner section of the sill assembly beneath the door aperture, running along the lower edge of the...

Towing Jaw rated to 3.5 tonnes, part of the towing/pintle hitch assembly. It provides the jaw coupling for trailer and recovery towing, mounting t...

Front Axle Drive Shaft Spacer for the front hub and stub axle assembly. The spacer fits over the front drive shaft and sets the axial position of ...

Synchro Cone (Baulk Ring) - LT95 4-Speed Gearbox This synchro cone, also known as a baulk ring, is a component of the synchroniser assembly within...

Differential Pinion Bearing Shim - 0.070 in, for use in the Rover 10-spline rear differential. This shim sets the preload on the pinion outer beari...

Valve Cotter in the cylinder head valvetrain, locking the valve spring retainer to the valve stem. The cotters seat as a pair into the machined gr...

Valve Spring Cap for the cylinder head valve train. The spring cap seats on top of the valve spring and locates against the split collets on the v...

Driveshaft Oilpump

Throttle Linkage for the 3.5L V8 fitted with twin Stromberg 175CD carburettors. This linkage connects the throttle pedal input to both Stromberg c...

Valve Cotter (split collet) for the Rover V8 petrol engine valve train. Locks the valve spring retainer to the valve stem, holding the spring unde...

Distributor Drive Gear for the Rover 3.5L V8 petrol engine. The gear forms part of the ignition distributor drive assembly, transferring rotationa...

Tow Hitch Locking Pin (R-Clip) is the spring-steel retaining clip that secures the tow pin in an adjustable tow hitch. It pushes through the hole i...

Towing Bracket Slider is the sliding tongue section of a Dixon Bate adjustable towing bracket, which sets and locks the hitch at the required heigh...

Clutch Slave Cylinder Repair Kit for the hydraulic clutch release circuit on V8 petrol applications. The clutch slave cylinder is actuated by hydr...

Blanking Plug - plastic plug sealing a 1-1/4" (32mm) diameter aperture in the rear cross member. Installs into unused or access holes in the bodys...

Nut FQA

Self-Tapping Screw - a No. 10 x 1/2" self-tapping screw used as a general-purpose fixing. The self-tapping thread cuts its own mating thread as th...

Screw - a No. 8 x 1" self-tapping screw used to secure the wing-top air intake grille. It fastens the air intake grille to the top of the front wi...

Self-Tapping Screw - a No. 6 x 1/2" imperial self-tapping fixing used as a general-purpose fastener throughout the body and chassis. The self-tapp...

Screw for use in Land Rover body, chassis, and hardware applications.

Bolt used in the LT95 gearbox and transfer assembly. It provides a torque-loaded, clamped fastening securing components within the LT95 transmissi...

Nutsert - 1/4" UNF is a blind rivet nut (rivnut) with a 1/4" UNF internal thread. A nutsert is installed into a pre-drilled hole in sheet metal or...

Distributor Drive Gear - V8

Valve Guide for the Rover V8 cylinder head. Pressed into the cylinder head, the guide supports the valve stem and keeps the valve concentric with ...

Intake Elbow Seal for the 3.5L V8 twin-carburettor petrol engine. The seal sits between the air cleaner intake elbow and the carburettor intake to ...

Bolt used in the camshaft assembly of the 3.5L V8 petrol engine. Imperial UNF fastener, 7/16" diameter with a shank length of 1 1/8". Supplied as ...

Cylinder Head Bolt - a 7/16" UNC x 2.71" medium-type bolt for the Rover V8, part of the cylinder head fixings. This is the medium-length head bolt...

Cylinder Head Bolt Washer seats under the head of a 7/16in cylinder head bolt on the Rover V8 petrol engine. It distributes clamping load across t...

Inner Ring

Vacuum Actuator O-Ring for the LT95 4-speed gearbox. This O-ring seals the vacuum actuator fitted to the LT95 transfer case mechanism, used on V8-p...

Circlip is a split retaining ring that locates on the reverse shaft of the LT95 gearbox. It seats into a machined groove to axially retain the rev...

Circlip for the throttle linkage on the carburettor V8 engine. It retains a pin or clevis within the throttle linkage, holding the linkage componen...

Tappet Guide (guide only) locates and retains the tappet roller assembly within the engine block, maintaining correct alignment of the tappet as it...

Edge Clip - Door Lock Mechanism with various applications across Land Rover Series, Defender, Discovery 1, and Range Rover Classic models. This sp...

Special Bolt with a coarse ACME-form thread, 1/4 in diameter and 5/8 in long. It is a body fixing used to secure inner-wing mudshields, floor plat...

Bolt - 5/16" UNF x 5/8" is a general-purpose hexagon-head set bolt in 5/16 UNF (Unified National Fine) thread, 5/8 inch in length. Used across engi...

Wiper Motor Mounting Pad for the rear wiper motor, used on the Defender and Range Rover Classic. This rubber fixing pad sits between the wiper mot...

Brush kit RTC830 fits: Rover 3.5L V8 startermotor type 3M100 - S3 109" stage 1 V8 - 101" Forward Control - Range Rover Classic

Diesel Fuel Filter Plug Seal - a sealing ring for the drain plug on the diesel fuel filter and sedimentor. It seals the drain/bleed plug against t...

Fuel Pump Gasket seals the external fuel pump to its mounting face in the fuel delivery system, preventing leakage at the joint. Used on petrol ap...

Clip - a retaining clip within the vehicle body hardware, used to secure and locate a fitted component in position.

Gearbox Selector Circlip - a retaining circlip within the manual transmission gear selector mechanism. The circlip locates on its shaft to secure ...