Land Rover Series Parts

Bolt securing the bulkhead to the chassis outrigger. A 1/2" UNF hex-head bolt used at the lower bulkhead mounting points, where the bulkhead fixes...

Exhaust Clamp for the exhaust-to-chassis mounting. Two-bolt upper clamp plate that forms the exhaust-to-chassis mounting assembly on Series and ea...

Condenser for the distributor ignition system. The condenser (capacitor) is wired across the contact breaker points inside the distributor. As the...

Reverse Gear Selector Detent Spring for the manual gearbox selector mechanism. The spring loads the detent ball against the reverse selector shaft...

Reflector SIII

Right-hand front glazed door top assembly forming the upper section of the door structure. This component provides the framed aperture for the sl...

Bolt, 1/4" BSF x 1", serving as the steering lockstop in the front axle steering assembly. The bolt threads into the swivel housing and is set to l...

Handbrake Shoe Set for the transmission-mounted drum handbrake. The shoes expand against the drum at the transfer box output to hold the vehicle w...

Distributor Cap for the Lucas distributor fitted to the four-cylinder petrol engine, part of the ignition system. The cap seats over the distribut...

Bulkhead Vent Hinge Pin Kit in stainless steel - replaces the pivot pins on which the bulkhead (scuttle) air vent flaps hinge. The original steel ...

Rear Wiper Blade for the rear screen wiper assembly, clipping to the wiper arm to sweep the rear glass. Fits wide 7mm wiper arms only - suits the ...

This camshaft sprocket is designed for Land Rover V8 engines, providing precise timing and reliable performance.

Toggle Switch is a two-position on/off switch in the dashboard switchgear, controlling the instrument and panel lighting circuit. The sprung toggl...

Grab Handle chassis-mounted exterior fitting, bolted to the vehicle chassis. It provides a fixed hand-hold at the chassis, giving a secure grab po...

T-piece imperial

Fir Tree Fastener secures interior body and roof trim panels to the vehicle structure. The ribbed, tapered fir-tree shank pushes into a panel hole...

Front Cover Gasket seals the timing cover to the front face of the cylinder block on the V8 petrol engine. It fits between the front cover and the...

Cylinder Block Drain Tap threads into the coolant jacket of the cylinder block, providing a controlled drain point for the engine cooling system. ...

Rocker Cover Gasket for the V8 petrol engine, cork construction. The gasket seals the joint between the rocker cover and the cylinder head, contai...

Wheel Cylinder - LH Front for the front drum brake assembly on long wheelbase Series models. This hydraulic wheel cylinder is mounted at the left-...

Taper Roller Bearing - Diff Pinion - Outer is the outer pinion bearing in the differential final drive assembly, supporting the pinion shaft where ...

Spare Wheel Bonnet Strap, the retaining strap for a bonnet-mounted spare wheel. Secures the spare wheel in the bonnet-top carrying position, holdi...

Interior Grab Handle - interior pull handle for the rear side door, used to draw the door closed from inside the cab. It fixes to the inner face o...

Clutch Slave Cylinder for the hydraulic clutch actuation system. Mounted on the gearbox bellhousing, this cylinder receives hydraulic pressure fro...

Side Cover Gasket sealing the cylinder-block side cover (tappet inspection cover) to the block face on diesel engines. The side cover closes the p...

Swivel Housing Washer for the swivel pin housing drain plug, part of the front axle swivel assembly. The sealing washer fits beneath the drain plu...

Contact Set for the Lucas 25D distributor in the ignition system of the 2.25L and 2.6L petrol engines. The contact set (breaker points) opens and ...

Exhaust Manifold Gasket Set - 2.0L & 2.6L

Shock Absorber - rear suspension damper for the short-wheelbase chassis. Mounted between the rear axle and the chassis bracket, it controls spring...

Seat Box Corner Protector - Pair - Black Steel

Wheel Cylinder for the rear drum brake assembly, right-hand side. The wheel cylinder forms part of the hydraulic drum brake circuit, converting hy...

Gearbox Reverse Stop Spring for the gear selector mechanism. The spring acts on the reverse stop plunger, providing the resistance the gear lever ...

Front Propshaft for the 4-cylinder 2.25L petrol driveline. It transmits drive from the transfer box front output to the front axle differential, de...

Water Pump for the engine cooling circuit, with the 9-hole mounting flange. Belt-driven, the pump circulates coolant through the block, cylinder h...

Rear Shock Absorber - rear suspension damper for the long-wheelbase chassis. Mounted between the rear axle and the chassis bracket, it controls sp...

Clutch Release Fork Kit for the manual transmission clutch release mechanism, built around a cast release fork. The fork pivots on its mounting in...

Mud Shield for the left-hand inner wing, left-hand drive configuration. This panel fits beneath the wing to shield the components behind it from mu...

Handbrake Gaiter - round-hole type - for the transmission handbrake (parking brake) lever assembly. This rubber gaiter fits over the base of the L...

Specifically designed for Series vehicles equipped with the Weber 34 ICH 2.25 carburettor, this kit includes all the essential components needed to...

Engine Bottom-End Gasket Set for the 2.25L 4-cylinder petrol engine, supplying the lower-engine gaskets and seals used during a bottom-end overhaul...

Swing-away spare wheel carrier is designed to support and relocate the spare wheel at the rear door, allowing hinged outward movement for improved ...

Clutch Cover (pressure plate assembly) for the clutch on 4-cylinder petrol applications. The cover bolts to the flywheel and houses the diaphragm ...

Chassis Bush - 88in - Front is a rubber bush that fits the rear mounting point of the front leaf spring, locating the spring in the chassis-side sh...

Clutch Slave Cylinder, part of the hydraulic clutch release circuit. The slave cylinder receives fluid pressure from the clutch master cylinder an...

Pedal Box Gasket for the pedal box housing assembly. Seals the mounting joint between the clutch and non-servo brake pedal housing and the bulkhea...

Rotor Arm for the ignition distributor of the 2.6L 6-cylinder inline petrol engine. The rotor arm fits on the top of the distributor shaft and tur...

Head Gasket Set - 2.25 Petrol - Composite is a top-end (de-coke) gasket set for resealing the cylinder head assembly of the 2.25-litre petrol engin...

Brake Master Cylinder - Dual-Line is the hydraulic master cylinder of the dual-line servo braking system, converting brake-pedal force into hydraul...