Land Rover Series Parts

Set Screw, M8 x 70 mm. A fully threaded hexagon-head fastener in high-tensile steel with a bright zinc-plated finish. Used across a range of chassi...

Screw M6 x 20 pan-head screw. It can be used in place of LR083229 (RYG500650 / DYP500210 / EYG50080) but is not identical: this screw has no capti...

Temperature transmitter

Oil Temperature Transmitter for the engine instrumentation circuit. The transmitter threads into the oil gallery and varies its electrical resistan...

Nyloc Nut with an M16 thread - a nylon-insert locking nut used on heavily loaded suspension and driveline fixings. A nylon collar set into the top...

Seal

Mud Shield for the right-hand inner wing, left-hand drive configuration. This panel fits beneath the wing to shield the components behind it from m...

Rear Stop/Tail Lamp - LED - LED combined stop and tail lamp with a red lens, supplied as a complete sealed unit to replace the standard rear stop/t...

Clutch Driven Plate (friction disc) for the clutch assembly, 9 1/2 inch diameter. The driven plate is clamped between the flywheel and the pressur...

Glow Plug for the diesel cold-start pre-heating system, threaded into the cylinder head to project into the combustion chamber (or pre-combustion c...

Oil Pump Gasket for the engine lubrication system, sealing the oil pump to its mounting face on the cylinder block. It maintains a leak-free joint...

Brake & Clutch Master Cylinder - Combined CV-Type serves both the braking and clutch hydraulic circuits from a single unit. In this CV-type de...

Clutch Master Cylinder Overhaul Kit for rebuilding a CV-type master cylinder, allowing the worn internal components to be renewed without replacing...

Windscreen Seal - 2.5m is the rubber glazing seal for the windscreen, supplied as a 2.5 m length. It seats the windscreen glass in its aperture an...

Front Exhaust Pipe (downpipe) for the 2.25L diesel engine, forming the first section of the exhaust system. The front pipe bolts to the exhaust ma...

Gearbox-Transfer Box Gasket for the LT76 gearbox, sealing the mating joint between the gearbox and the transfer box. The gasket maintains the oil-...

Differential Drive Flange for the Salisbury rear differential. It bolts to the differential pinion shaft and forms the coupling face to which the r...

Core Plug for the V8 petrol cylinder block and inlet manifold. The cup-type plug seals the casting core holes left in the coolant jacket after man...

Past op alle benzine en diesel 109"" modellen (knevel sluiting)

Heater Hose connects the cylinder head heater outlet into the heater coolant circuit, carrying hot coolant from the engine toward the heater matrix...

Wheel Stud for the axle hub - 16mm pull-in type. Mounts in the hub flange to carry the road wheel, which is clamped by the wheel nut running on th...

Oil Seal for the front output shaft of the LT95 gearbox, sealing the transfer case around the rotating output shaft. The LT95 is a combined main g...

Expansion Tank Cap seals the cooling system expansion (header) tank. The plastic cap closes the tank and holds the coolant circuit at its rated pr...

Master Cylinder Nut for the CB-type brake master cylinder, fitted to the end of the cylinder bore. The nut closes and retains the end of the maste...

Grommet - a rubber panel grommet providing a sealed, protected pass-through for the choke cable and windscreen washer tubing. Fitted into the pane...

Core Plug for the cylinder head, sealing a core hole left in the casting during manufacture. It closes the opening left by the casting sand core a...

Fuel Cap Locking Hasp is the body-mounted latch in the fuel filler arrangement that secures the petrol filler cap against unauthorised opening. It...

Bulb rated 12V 10W with a BA15S bayonet cap. A single-contact bayonet-fitting (BA15S) bulb for 12-volt circuits. The single-contact cap suits sing...

Split Pin Assortment A 280-piece assortment of split pins (cotter pins) in a range of sizes, supplied as a workshop set. Split pins secure castell...

Windscreen Hinge Bolt is a fixing used to secure the folding windscreen frame hinge to the scuttle. It clamps the hinge mounting at the base of th...

Radiator Grille mounts in the front body panel aperture, ahead of the radiator, admitting cooling airflow to the core while protecting it from road...

Accelerator Pedal Return Spring for the cable-operated throttle linkage. The spring returns the accelerator pedal to its rest position when foot p...

Lock Nut with a 5/16" BSF thread. The lock nut secures a threaded fastening against loosening under vibration, maintaining clamp load in service. ...

Exhaust Saddle Clamp for securing exhaust pipe sections to underbody mounting brackets in the exhaust system. The U-shaped saddle body seats over ...

Oil Cooler for the engine lubrication system, in 4-cylinder Military Lightweight specification. Connected into the engine oil circuit, it passes t...

Brake Clevis A clevis for the brake drum expander mechanism within the drum braking system. It forms the pinned link between the brake operating r...

Sealing Washer - copper sealing ring for the cooling system drain points. It seats under the radiator drain plug and the cylinder block drain tap, ...

Glazing Rubber Seal for retaining glass panels in fixed window aperture frames. This flexible rubber channel seal locates in the groove of the win...

Valve repair kit

24v dsl long belt

Gear Lever Locating Pin locates and retains the main gear lever within the manual gearbox. It holds the lever against its pivot so that shift move...

Spring plate

Halfshaft Collar is a locating collar fitted to the front axle halfshaft. It seats against the inner side of the halfshaft bearing (244150), setti...

Bolt, a hexagon-head fastener with a 5/16" UNF thread, 7/8" long. This imperial fastener is of the UNF (Unified National Fine) thread series and i...

Wheel Spanner - 24mm for removing and fitting wheel nuts on Land Rover vehicles. This 24mm spanner is sized for the standard wheel nut used across...

Hazard Flasher Relay - the switching relay in the hazard warning circuit. When the hazard switch is operated, the flasher relay pulses all four di...

Fitment: All models to 1980 except V8

Joint Washer seals the gearchange/inspection cover against the transfer box casing within the transfer gearbox assembly. Fitted between the cover ...