Land Rover Series Parts

Rocker Cover Gasket (Top) - seals the rocker cover joint on the 2.6L 6-cylinder petrol engine. Fitted between the rocker cover and the cylinder he...

Gasket

Exhaust Clamp Plate for the exhaust mounting assembly. Three-hole clamping plate that secures the exhaust pipe within the mounting bracket assembl...

Glazing Rubber Strip - rubber glazing section supplied by the metre. It beds and seals a fixed glass panel into its body aperture, locating the gla...

Seat Back for the outer front seat, in the deluxe pattern and finished in black. This is the upholstered backrest (squab) the occupant leans agains...

Castle Nut (castellated nut) used to retain halfshafts, output shafts and differential pinion shafts in Land Rover axle and drivetrain assemblies. ...

Choke Clip is the retaining clip that secures the choke cable at the Zenith carburettor. Part of the choke cable installation, it anchors the oute...

Heater Distribution Control Cable - the Bowden cable that links the dashboard heater control to the air-distribution flap in the heater assembly. ...

Steering Wheel Boss in the steering column assembly, providing the mounting interface between the column shaft and the steering wheel. The 48-spli...

Headlamp Bulb - 12V 40/45W Non-Halogen - LHD

Gearbox Bearing is the ball bearing that supports the primary pinion, or first motion shaft, in the main gearbox. Located at the front of the gear...

Ball Bearing for the transfer box, supporting the output shaft and its output flange. Fitted in the LT230 and NV225 transfer boxes, the bearing lo...

Fan Belt for the engine auxiliary (accessory) drive. Transmits drive from the crankshaft pulley to the water pump, cooling fan and dynamo or altern...

Track Rod End for the steering linkage, with a left-hand thread and a fully threaded shank. The track rod end forms the ball-jointed connection be...

Shock Absorber - Front - LWB

HT Ignition Lead Set for the 2.25L and 2.5L 4-cylinder petrol ignition system. This set of four high tension leads connects the distributor to eac...

hinge door LH upper with holes for mirror arm. Series 3 and early classic Defender. This is the "smaller" version, used upto (VIN) WA138479 (1998 m...

Exhaust Connecting Pipe is the intermediate section of the exhaust system, joining the front pipe to the rear silencer. It carries exhaust gas alo...

Reverse Lamp forming part of the rear lighting assembly, providing white illumination to the area behind the vehicle when reverse gear is selected....

Front Lamp Guards – a hinged protective guard set for the front exterior lamps. The guards mount over the front headlamps to shield the lenses fro...

Mirror Arm for a door-mounted exterior mirror, within the exterior mirror assembly. This is an extended arm of the Wolf (XD) pattern, holding the ...

Tailgate latch assembly HCPU

Clutch Release Fork operates inside the bellhousing as part of the manual transmission clutch release mechanism. Pivoting on its mounting in the c...

Barrel Lock & Key is the lock barrel and matching key for the ignition/starter switch. This is the diesel-application barrel for the earlier t...

hinge front door RH upper with holes for mirror arm "smaller" version for Series 3 and early classic Defender upto (VIN) WA138479 (1998 model year)

Inlet Manifold Joint Washer seals the inlet manifold to the cylinder head. It maintains an airtight joint between the manifold flange and the head...

Parabolic Spring Kit - 2-Leaf Front Pair is a front leaf-spring suspension set that replaces the original semi-elliptic multi-leaf front springs. ...

Plain Washer - imperial-dimensioned flat washer with an internal diameter of 7/16 inch and an outer diameter of 13/16 inch. Used in general fasten...

Bulkhead Outrigger is a welded structural support bracket in the bulkhead and chassis assembly, tying the base of the bulkhead to the chassis frame...

Screw used as a securing fastener in the pedal box area and in brake pipe routing. This screw retains the cover plate at the top of the pedal box,...

Hex-head bolt, 3/8" UNC thread, 3/4" long. Unified Coarse (UNC) thread form with a hexagonal head for use with standard imperial spanners and sock...

Hex-head bolt, 5/16" UNF thread, 3/4" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and socke...

Contact Set for the ignition distributor of the 3.5L V8 petrol engine. The contact breaker points open and close the primary circuit to the ignitio...

Glass Fuse rated at 5A, a cartridge-type fuse used in the vehicle electrical system. The fuse seats in the fuse box or an inline fuse holder and p...

Air Filter Element for the engine air intake system, housed within the air cleaner assembly. It traps airborne dust and abrasive debris from the in...

T-Piece is a three-way connector in the windscreen washer fluid circuit. It joins the washer hose into two branches, distributing fluid from the p...

Fuel System Seal Ring

Door Bottom Seal for the front door. This rubber seal fits along the lower edge of the door, closing the gap between the door bottom and the body t...

Brake Pipe Union - a female threaded union nut for the brake hydraulic pipework, with a 7/16"-20 UNF thread sized for 1/4" brake pipe. It fastens ...

Hub Cap fits over the end of the front or rear hub, enclosing the drive flange and hub assembly. It closes off the outer end of the hub to retain ...

Distributor - contact-breaker (points) ignition distributor for the 4-cylinder petrol engine. Distributes the high-tension spark to the cylinders ...

Inline Fuel Filter for petrol fuel-injection (EFI) systems, fitted in the pressurised fuel supply line between the fuel pump and the injector rail....

Starter Motor for the 2.5L 4-cylinder diesel engine, part of the engine electrical starting circuit. When the ignition is operated the solenoid th...

Flywheel Bolt securing the flywheel to the rear flange of the crankshaft. Used on four-cylinder petrol and diesel engines, including the 200TDi an...

Cellular Dynamic Shock Absorber A long-travel front damper that controls axle movement within the suspension, mounted between the chassis and the f...

Brake Hose Kit is a three-hose set of standard-length stainless-steel braided brake hoses that replace the flexible sections of the hydraulic brake...

Jubilee Clip - 21-44mm is a worm-drive hose clip with a 21-44mm clamping range. The band is tightened by a captive worm screw to clamp small- to m...

Bolt 1/4" UNF x 2" is a hex-head set bolt with a 1/4-inch Unified National Fine (UNF) thread at 28 threads per inch and a 2-inch shank length. It ...