Land Rover Series Parts

Plain Washer - flat washer for use in general fastening assemblies throughout the vehicle. Distributes load and protects mating surfaces under bol...

Auxiliary Fuel Tank for the fuel storage system, in the original military pattern. This under-seat auxiliary petrol tank supplements the main fuel...

Mirror Head - 195 mm x 145 mm. The rectangular exterior mirror head that fits the bar-type mirror arm, providing the driver's rearward view along t...

Rocker Shaft for the valvetrain of the Rover V8 petrol engine. The shaft mounts on the cylinder head and carries the rocker arms, transferring pus...

Bolt - 5/16" UNF x 1/2" - a hex-head set screw with a 5/16" UNF (Unified National Fine) thread and 1/2" length. Fully threaded to the head, it pro...

Size/Diameter: 1/4" unf x 7/8"

Countersunk Screw - a machine screw with a flat, cone-shaped head that seats flush with the surface it fixes, leaving no proud edge. Metric M6 thr...

Pan Head Screw - a machine screw with a low, rounded-top head and a flat bearing face, used as a general-purpose fixing. Metric M6 thread with a 1...

Ignition Condenser for the contact-breaker distributor, of the Ducellier type. Wired across the contact-breaker points, the condenser absorbs the ...

Starter Motor for the engine starting system - a 12V high-torque gear-reduction unit for petrol applications. The starter mounts to the bellhousin...

Shock Absorber for the rear suspension, forming part of the rear axle damping assembly. This telescopic hydraulic damper is fitted between the cha...

Shock Absorber for the front axle, damping suspension movement by converting the energy of spring oscillation into heat as the axle moves relative ...

Handbrake Shoe - V8 - LT95 is a brake shoe for the transmission-mounted parking brake used with the LT95 four-speed gearbox. Rather than acting at...

Brake Master Cylinder Repair Kit for the non-ABS brake master cylinder. The kit renews the internal seals when the master cylinder is overhauled, ...

Alternator Brush Set replaces the carbon brushes in an ACR-type alternator, within the charging system. The brushes bear on the rotor slip rings a...

Electric Fuel Pump mounted externally in the fuel supply system, drawing petrol from the tank and delivering it to the carburettor. This is an ext...

Wiper Arm - windscreen wiper arm, left-hand. The 7mm is the wide width of the arm, which sets the wiper-blade fitting - it is not a spindle size. ...

Rear Fog Lamp for the rear lighting circuit, providing the high-intensity red rear light used to make the vehicle conspicuous from behind in poor v...

Transfer Gear Knob - High/Low - LT95 is the hand grip fitted to the high/low range transfer lever on the LT95 gearbox. It threads onto the top of ...

Head Gasket Seals the cylinder head to the cylinder block on the pre-TDi 2.25L and 2.5L naturally aspirated and turbocharged diesel engines. It co...

Sealing ring

Sealing O-Ring for the joint between the flywheel housing and the engine block on the 2.25L 5-bearing petrol and 2.5L naturally-aspirated diesel en...

Crankshaft Pulley for the 2.25L and 2.5L 4-cylinder petrol engine. It mounts on the nose of the crankshaft and drives the cooling fan, water pump a...

Injector Leak-Off Pipe for the 2.25L and 2.5L naturally-aspirated diesel fuel injection circuit. This spill-return pipe connects the return unions ...

Carburettor Gasket - a sealing gasket for the Zenith-Stromberg 175CD carburettor as fitted to the 3.5 litre V8. It seals a joint within the carbur...

Oil Pressure Sensor Monitors engine oil pressure in the lubrication circuit and signals the oil pressure gauge or warning lamp on the instrument pa...

Footwell Repair Panel is a welded body repair panel for the left-hand (offside) footwell, replacing the corroded or damaged footwell section ahead ...

Bolt - an imperial hexagon-head bolt with a 5/16" UNF thread and a 2-3/4" shank length. This is an engine-area fixing for early Series application...

Bolt 1/4" UNF x 2-1/2"

Sedimentor Seal for the diesel fuel sedimentor assembly. The sedimentor separates water and sediment from the fuel ahead of the injection system. ...

Windscreen Washer Non-Return Valve fits inline in the washer fluid delivery pipe, forming part of the windscreen washer system. It allows fluid to...

Oil Strainer Gasket for the Rover V8 petrol engine, sealing the flanged joint of the oil pick-up strainer inside the sump. Renew it whenever the p...

Input shaft oil seal

Single Clip is a single-aperture retaining clip used to secure brake and fuel pipes, the accelerator cable and the hand throttle control. It holds...

Collapsible Salisbury spacer

Oil Thrower for the drive pinion in the Salisbury axle differential. It fits on the pinion shaft, between the drive flange and the pinion oil seal....

Carburettor Grommet for the twin Stromberg carburettor installation on the V8 petrol engine. It sits in the air cleaner and carburettor air intake ...

Core Plug for the rear of the camshaft bore in the V8 petrol cylinder block. The cup-type plug seals the machined opening at the rear of the camsh...

U-Bolt – Rear – 1-Ton clamps the rear leaf spring to the axle. The U-shaped bolt passes over the axle and through the spring seat plate, where its ...

Half Shaft – Rear RH – 10-Spline Short is the rear axle drive shaft for the right-hand side. It carries the drive from the differential out to the ...

Oil Filler Cap Assembly for the rocker (valve) cover of the 2.25L 4-cylinder petrol engine. The cap seals the oil filler neck and incorporates an i...

Brake master cylinder (single line with servo)

Valve Guide A precision sleeve pressed into the cylinder head that supports and locates the inlet valve stem, holding the valve concentric with its...

Brake Pipe - Front - LH - Series

Injector Pipe No.3, a high-pressure delivery pipe in the diesel fuel injection system. The rigid steel pipe carries fuel under high pressure from ...

Injector Pipe No.2, a high-pressure delivery pipe in the diesel fuel injection system. The rigid steel pipe carries fuel under high pressure from ...

Injector Pipe No.1, a high-pressure delivery pipe in the diesel fuel injection system. The rigid steel pipe carries fuel under high pressure from ...

Clevis Pin - a linkage pin used in the accelerator and throttle control. It joins the throttle cable clevis to its operating lever, allowing the l...