Land Rover Series Parts

Set Screw - a fully threaded hexagonal-head setscrew with a 3/8" UNC (Unified Coarse) imperial thread and a 7/8" length. Used as a Rover V8 engine-...

Shock Absorber Washer Retaining washer for the rear shock absorber lower mounting. Part of the rear suspension assembly, it locates over the lower...

Contact Set for the Lucas distributor fitted to Land Rover petrol engines, comprising the breaker point assembly within the conventional ignition s...

Split Pin - a 1.5mm x 12mm cotter pin used to lock a slotted (castle) nut or to retain a clevis pin. Passed through a drilled cross-hole in the sh...

Plug Washer for the drain and filler/level plugs on the LT95 gearbox and differential. The washer seats between the threaded plug and the casing t...

Exhaust Valve Stem Seal for the cylinder head valvetrain. Fits over the exhaust valve stem at the top of the valve guide, metering the oil that pa...

Seat Box End Panel for the left-hand end of the seat box - the structural box that forms the seat base across the centre of the vehicle. This repa...

Bolt - an imperial hexagon-head bolt with a 5/16" UNF thread and a 3-1/4" shank length. This long-shank bolt is used at the alternator mounting on...

Polyurethane Suspension Bush Kit - a full-vehicle set of replacement suspension bushes for the Series 3 long-wheelbase (109") chassis, supplied in ...

Water Pump Seal

Blanking Plug for closing an unused 16 mm (5/8") hole in body or trim panelling. A push-in plastic plug used to blank off redundant or open apertu...

Engine Mounting Bracket - right-hand front engine mount angle adaptor. Bolts to the right-hand side of the cylinder block and carries the rubber e...

Glow Plug for the 2.25L diesel engine running a parallel (converted) glow plug system. Part of the cold-start pre-heating circuit. The glow plug h...

Front Shackle Plate forms part of the front leaf-spring shackle assembly, connecting the road spring eye to the chassis mounting. The shackle allow...

double washer, restrictor

Spring Washer is a split spring lock washer fitted under a nut or bolt head to maintain clamping tension and resist loosening caused by vibration. ...

LWB voorste ophangpunt van achterste veer LH en RH

Front Brake Shoe Set for the front drum brakes. The brake shoes carry the friction linings that are forced outward against the brake drum by the w...

Decoke Gasket Set for the 3.5L V8 petrol engine with twin carburettors. The set supplies the gaskets needed when the cylinder heads are removed fo...

Hex-head bolt, 7/16" UNF thread, 1-1/4" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and soc...

Contact Set (breaker points) for the contact-breaker distributor, of the Ducellier type. The points are opened and closed by the distributor cam t...

Contact Set for the distributor of the 2.25L petrol engine, 24V FFR (Fitted-For-Radio) military specification with screened ignition. The contact ...

Radiator for the engine cooling system, mounted at the front of the vehicle to dissipate heat from the coolant circulated by the water pump. Air dr...

Thin Nut - a reduced-height hex nut with a 5/16" UNF (Unified Fine) thread. The shallow profile suits fastening points with limited clearance and ...

Exhaust U-Bolt - a U-bolt clamp used to secure a joint in the exhaust system. It retains the exhaust front pipe (downpipe) connection, clamping th...

Engine Stop Cable is the manual control cable that shuts down the 2.25L diesel engine by pulling the fuel injection pump stop lever to the no-fuel ...

Hex Nut is a metric M5 hexagonal nut used as a general-purpose threaded fastener across multiple vehicle assemblies. It runs onto a matching M5 ma...

Wing Fixing Plate is a two-stud captive stud plate used in the front body mounting assembly, where it secures the front wing to the radiator (front...

Seat Belt - 3-Point Inertia Reel is a lap-and-diagonal front seat belt assembly with a self-locking inertia reel, supplied to the basic Type A spec...

Differential Thrust Washer for the LT230 transfer box centre differential. It bears against the differential gears within the centre differential,...

Timing Chain for the 2.25L and 2.5L four-cylinder petrol engines with the five-bearing crankshaft, running inside the front timing cover. It drive...

Engine Lifting Bracket bolts to the cylinder head and provides a rated attachment point for hoisting the engine. Fitted to the four-cylinder petro...

Cellular Dynamic Shock Absorber A long-travel rear damper that controls axle movement within the suspension, mounted between the chassis and the re...

Steering Wheel - a 14-inch three-spoke replacement wheel with a black vinyl rim and black centre. The wheel mounts to the steering column through ...

Hose Clip - Jubilee - 70-92mm is a worm-drive band clamp with a clamping range of 70-92 mm. It secures a hose over its spigot or connector, compre...

Headlamp Bulb - a 24V dual-filament bulb for the main headlamp, rated 55/50W with a P45T base. The two filaments carry the main and dipped beam wi...

Bolt with a 3/8" UNF (Unified National Fine) imperial thread and a 4-1/2" shank length. A long-shank hex-head fastener for general assembly and fi...

Bolt with a 5/16" UNF (Unified National Fine) imperial thread and a 4" shank length. A long-shank hex-head fastener for general assembly and fixin...

Bolt - M8 x 100mm hex head bolt used in the transmission mounting assembly. Secures transmission mounting components on Series III vehicles equipp...

Joint Washer - a sealing washer for the piston-cooling oil squirt jet in the engine lubrication circuit. It seals the oil spray jet where it meets...

Restore and reinforce your Land Rover's rear floor structure with this galvanised body crossmember floor, designed for Defender and Series 2, 2A, a...

Drive Screw - a No. 6 x 1/2" self-tapping drive screw used across door and facia assemblies. It secures the front door glass and window regulator,...

Self-Tapping Screw - a No. 8 x 3/8" self-tapping screw used as a general-purpose fixing. The self-tapping thread cuts its own mating thread as it ...

Camshaft Lock Washer retains the camshaft gear securing bolt at the front of the camshaft, part of the engine timing drive. After the bolt is tigh...

Front Shackle Plate forms part of the front leaf-spring shackle assembly, connecting the road spring eye to the chassis mounting. The shackle allow...

Exhaust Clamp for the V8 engine exhaust system, securing a front-pipe joint. The clamp draws two pipe sections together at their slip joint, holdin...

Heater Hose – Inlet carries hot coolant from the engine cooling circuit to the heater matrix, forming part of the cabin heating system. The inlet ...

Rivet is a permanent mechanical fastener used in the lower tailboard (drop-down tailgate) hinge assembly. Set through the hinge components, it for...