Land Rover Series Parts

O-Ring for use in two distinct applications on classic Land Rover engines. On the Series IIA 2.6L 6-cylinder engine, this O-ring seals the cylinde...

rod control GENUINE LR - 2.25 petrol and 2.6 petrol, 1968 onwards

Sump - 2.25 Petrol/Diesel - 2.5 Petrol is the engine oil sump (oil pan) for the 2.25L 4-cylinder petrol, 2.25L 4-cylinder diesel, and 2.5L 4-cylind...

Layshaft Distance Piece - 0.445in is a precision spacer fitted to the layshaft in the manual gearbox of Series IIA and Series III Land Rovers. The...

Locating Screw for the engine. A locating screw sets and holds the position of a component against its mounting during assembly. Applies to the 2....

Bush - Low Gear Wheel is a gearbox internal bush fitted to the low gear wheel in the Series 2 and Series 3 manual gearbox on 109-inch 1-ton Land Ro...

Circlip for the throttle linkage on the carburettor V8 engine. It retains a pin or clevis within the throttle linkage, holding the linkage componen...

Slip Ring for the horn contact in the steering column. This contact ring maintains the electrical connection to the horn as the steering wheel tur...

Blanking Plug

Inlet Valve Guide - a cylinder-head valve guide for the inlet valves of the 2.6L six-cylinder petrol (IOE) engine. Pressed into the cylinder head,...

Bush - Accelerator Linkage is a small bearing bush fitted to the accelerator linkage assembly on the 2.6L 6-cylinder petrol engine used in Series I...

Tappet Adjuster is the adjustment screw used to set valve clearance in the cylinder head of Land Rover Series 4-cylinder engines. The screw thread...

Tappet Screw - the valve-clearance adjusting screw in the rocker gear of the four-cylinder engine (3-bearing crankshaft), part of the valvetrain. ...

Brake & Clutch Reservoir Tank Kit, a replacement for the original single fluid reservoir that fed both the brake and clutch master cylinders. ...

Tappet Guide (guide only) locates and retains the tappet roller assembly within the engine block, maintaining correct alignment of the tappet as it...

Screw - a threaded fastener used to join or secure components.

Upper Rear Door Seal, the rubber weatherseal for the top edge of the rear door aperture. It seals the upper line of the rear door against the body...

bottom door Series RH Series 3

Harness Bracket Shim for the wiring harness mounting hardware. Fitted behind the harness support bracket at its mounting point, the shim sets the ...

Door Latch Shim - Rear - a packing shim for the rear door anti-burst latch, part of the door lock and handle assembly. Fitted behind the latch on ...

Heater Control Mounting Plate for left-hand drive applications. Fitted within the heater control assembly in the cab interior, this plate provides ...

Front outer wing RH SIII plastic

Sill Panel Rear 109 Not Station Wagon - LH

Rear Sill Panel for the right-hand side of the body understructure on long wheelbase (109 inch) models. Fitted at the rear sill position, this pane...

Blanking Plug for the instrument panel, fitted to close an unused aperture in the dashboard where an instrument, switch or gauge is not installed. ...

Heater Air Intake Trim fits the front wing air intake of the heating and ventilation system. It finishes the fresh-air intake aperture in the wing...

Edge Clip - Door Lock Mechanism with various applications across Land Rover Series, Defender, Discovery 1, and Range Rover Classic models. This sp...

Headlamp Bezel is the outer retaining surround for the headlamp unit, mounting within the front lighting panel. It secures and finishes the lamp a...

Door Lock Button - LH - Push & Twist for Land Rover Series vehicles from 1954 to 1981. This left-hand push-and-twist door lock button fits the...

Door lock RH

Front Sill Panel for the right-hand side, of the narrow sill type. The sill is the structural panel running along the lower edge of the body benea...

Clevis Pin for the bonnet stay. Forms the pivot at the upper end of the bonnet prop, retaining the stay to the bonnet.

Rear Body Seal is a rubber seal fitted to the rear body extension panel of the station wagon body. The seal closes the gap between the extension p...

Door Seal - Left Hand is a body sealing component fitted to the left-hand door aperture. The seal runs around the door frame and compresses agains...

Rear Door Side Seal - Right Hand Side for the rear body of the 109" Station Wagon. This rubber seal runs along the side edge of the right-hand rea...

Check rod RH

Fitment: all models to 1980

Rear Wing Stay for the rear body assembly of Series II, IIA, and III Land Rovers (1958-1985). This stay bracket braces the rear wing against the b...

Inner Seat Base is the centre front seat base cushion, forming the lower seating platform of the basic vinyl front seat. Finished in black vinyl f...

Rope Hook - a securing hook for the canvas hood (soft top). It provides an anchor point around which the hood tie-down rope is passed, holding the...

Special Bolt with a coarse ACME-form thread, 1/4 in diameter and 5/8 in long. It is a body fixing used to secure inner-wing mudshields, floor plat...

Washer

Hinge Pin - the pivot pin for the top hatch (windscreen) hinge. It passes through the hinge knuckles to retain the two halves of the hinge while a...

Leaf Spring is the rear passenger-side leaf spring for long-wheelbase (LWB) chassis, of 8+2 leaf construction. Land Rover lists it as the left-hand...

Leaf Spring - LWB - Rear - Drivers Side

Intermediate Shaft

Rocker Bracket Locating Dowel for the cylinder head and rocker assembly in the 2.25L and 2.5L petrol and diesel engines. This dowel locates the ro...