Land Rover Series Parts

Carburettor Bell Crank Bush for the accelerator throttle linkage on the 2.25L 4-cylinder petrol engine. The bush locates the throttle bell crank a...

Front leaf spring LWB diesel DS

Oil Feed Pipe is the external oil feed pipe supplying the cylinder head within the engine lubrication system. It carries pressurised oil from the ...

Bracket

Top cover

Spring - Timing Ratchet sits within the engine timing assembly on Land Rover 2.25L and 2.0L diesel engines. This spring provides the retention for...

Leaf Spring - Front - 11-Leaf A semi-elliptic front leaf spring built up from an eleven-leaf pack, part of the front suspension. It carries the ch...

Bolt - 5/16" UNF x 5/8" is a general-purpose hexagon-head set bolt in 5/16 UNF (Unified National Fine) thread, 5/8 inch in length. Used across engi...

Manifold Stud is used to secure the combined inlet/exhaust manifold assembly to the cylinder block on Series vehicles fitted with the 2.25L diesel ...

Timing Chain Tensioner Spring for Land Rover 2.0L Diesel and 2.25L Petrol and Diesel four-cylinder engines. This spring applies constant pressure ...

Sealing Ring - Rocker Cover Breather Bolt for the 2.25-litre 4-cylinder engine. This sealing ring is fitted under the rocker cover breather bolt, ...

Stud for use in Land Rover gearbox assembly.

Mainshaft Bearing for the gearbox mainshaft - the centre bearing that supports the mainshaft within the gearbox casing. It locates and carries the...

Mainshaft Bearing for the gearbox mainshaft - the centre bearing that supports the mainshaft within the gearbox casing. It locates and carries the...

Wiper Motor Mounting Pad for the rear wiper motor, used on the Defender and Range Rover Classic. This rubber fixing pad sits between the wiper mot...

Brush kit RTC830 fits: Rover 3.5L V8 startermotor type 3M100 - S3 109" stage 1 V8 - 101" Forward Control - Range Rover Classic

Water Pump Casing for the engine cooling circuit, the housing that carries the coolant pump and directs flow into the cylinder block. The casing l...

Diesel Fuel Filter Plug Seal - a sealing ring for the drain plug on the diesel fuel filter and sedimentor. It seals the drain/bleed plug against t...

Fuel Pump Gasket seals the external fuel pump to its mounting face in the fuel delivery system, preventing leakage at the joint. Used on petrol ap...

Bolt, a threaded fastener used on the 2.0L petrol engine.

Bolt is a hex-head threaded fastener used to secure components at bolted joints, such as engine and starter-motor mountings.

Layshaft Bearing Distance Piece Spacer for the layshaft (cluster gear) bearing within the main gearbox. It locates against the layshaft bearing to...

Clip - a retaining clip within the vehicle body hardware, used to secure and locate a fitted component in position.

Gearbox Selector Circlip - a retaining circlip within the manual transmission gear selector mechanism. The circlip locates on its shaft to secure ...

Handbrake Catch Pawl, the ratchet claw of the transmission parking brake mechanism. It engages the toothed quadrant on the handbrake lever, lockin...

Exhaust Valve Guide for the 2.6L six-cylinder petrol engine. The guide is pressed into the cylinder head and locates the exhaust valve stem, holdin...

Barrel Lock and Key, Set of Three for the door locks, supplied as three keyed lock barrels each with a key. Each barrel is the cylinder the key tu...

Mainshaft Thrust Washer - 2nd Gear (0.125") is a selective shim located within the Series gearbox, fitted to control axial play on the second gear ...

Felt Seal for the clutch and brake pedal shaft, fitted in the pedal box where the cross-shaft passes through the housing. The felt washer seats ar...

Overdrive Needle Bearing for the front of the mainshaft in a Fairey overdrive unit. The bearing supports the overdrive clutch sleeve on the mainsh...

Voltage Regulator for the dynamo charging circuit – the Lucas RB340 control box. Wired between the C40 dynamo and the battery, the control box reg...

LED Driving Light - round auxiliary driving light with a 4" (100mm) diameter housing and 50W LED output. Intended for external mounting as a suppl...

Brake Kit - Series - SWB - To June 1980

Doortop Unglazed - LH

Bulkhead Top Corner Repair - LH

Screw: pan head self-tapping screw.

PTO Selector Cover Plate - a blanking plate for the power take-off (PTO) selector aperture on the transfer box. It covers and seals the selector o...

Hook & Loop Fastening Strap for securing and bundling loose items within the vehicle interior, cargo area, or workshop. The strap wraps around ...

Crankshaft Front Key locates and locks the timing sprocket or front pulley hub to the crankshaft snout, preventing rotational slip between the cran...

Track Rod End (Right-Hand) is the ball-joint connector at the end of the steering track rod, linking the track rod to the steering arm. It transmi...

4WD Selector Rod for the Series transfer box. It forms part of the four-wheel-drive engagement linkage, transmitting selector movement through the...

Gearbox Stud is a 1 3/4" threaded stud used in the gearbox and transfer box assembly. It provides a fixed threaded anchor for clamping casing join...

Transfer Box to Gearbox Mounting Stud, 2" length, used to fasten the transfer case to the rear of the main gearbox casing. This stud forms part of...