Land Rover Series Parts

Fuel filler breather hose

Grommet

Brake Master Cylinder is the hydraulic control unit of the braking system, generating the fluid pressure that actuates the wheel cylinders at each ...

Oil Filler Plug serving as the combined fill and level check point for the swivel pin housing, manual gearbox gearcase, and LT230 transfer box on L...

Oil filler cap

Water Pump Inlet Gasket - seals the water pump inlet housing against the engine front cover within the coolant circuit. It forms the joint between...

Brake Pipe Union for the hydraulic brake system, a female fitting in brass. This union connects a 3/16 inch brake pipe into the brake hydraulic ci...

Differential Carrier Gasket for the Rover-type axle assembly. The gasket seals the differential carrier housing against the axle casing at the cen...

Axle Key Washer for the hub nut locking system in the axle assembly. This tab washer seats beneath the axle hub nut, with tabs that locate into ma...

Crankshaft Rear Oil Seal for the engine bottom end, fitted at the rear of the crankshaft where it exits the block towards the flywheel. The seal r...

Master Cylinder to Pedal Box Gasket for the hydraulic clutch circuit. This gasket seals the mounting face between the clutch master cylinder body ...

Brake Hose - the flexible hydraulic line in the braking system. It carries pressurised brake fluid from the rigid chassis-mounted brake pipe to the...

Filler Plug sealing the fill and bleed point of the engine cooling system, fitted to the thermostat housing and the radiator. This brass plug clos...

Drain Plug for differential casings and LT230 transfer boxes. The tapered plug seals the oil drain, fill, and level holes in differential and axle...

Water Pump Gasket - 9-Hole for the cooling system on Land Rover Series 2.25L Petrol engines. This gasket seals the mating face between the water p...

Gasket thermostat by-pass Series 2.25 petrol and diesel.

Split Pin for use in the front and rear suspension assembly of the Series Land Rover. The split pin is inserted through the hole in a castle nut o...

Rear brake drum installed in the rear drum brake assembly of the vehicle braking system. The drum mounts to the rear hub and rotates with the wheel...

Exhaust Nut in brass, securing exhaust components to their mounting studs. The 5/16" UNF thread and brass construction resist seizing and corrosio...

Brake & Clutch Master Cylinder - Combined CV-Type serves both the braking and clutch hydraulic circuits from a single unit. In this CV-type de...

Ensure smooth and precise steering in your Series 2, 2A, and 3 with this comprehensive steering box repair kit. Designed to replace worn components...

Swivel Pin Lock Tab for the front swivel pin housing on Land Rover Series II, IIA, and III. Fitted to the 7/16 BSF studs that retain the swivel pi...

See fitting instructions: https://www.scribd.com/doc/208898844/Fitting-Instructions-for-RTC3176-Adjuster-Shoes-Drum-brake-LAnd-Rover-Series

Wiper Arm - front windscreen wiper arm, left-hand. The 5mm is the narrow width of the arm, which sets the wiper-blade fitting - it is not a spindl...

Nyloc Nut with an M10 thread - the nylon-insert locking nut used on U-bolt fixings. A nylon collar set into the top of the nut grips the bolt thre...

Brake Pipe Union - a male union fitting for 3/16" (4.75mm) hydraulic brake pipe, with a 7/16"-20 UNF thread. It clamps the flared pipe end against...

Exhaust Manifold Gasket for the 3.5L V8 petrol engine. This gasket seals the joint between the exhaust manifold and the cylinder head, preventing ...

Bolt - fixing bolt with an ACME (trapezoidal) thread form, used to secure the outer front wing to the bulkhead. It fastens the rear mounting flang...

Fuel Filler Hose - SWB for the fuel filler assembly on Series Land Rovers equipped with an under-seat fuel tank. This rubber hose connects the ext...

Shackle Pin - Long (9/16 UNF × 5-1/4 in.) for the front leaf spring shackle on Land Rover Series vehicles. This long shackle pin is fitted at the ...

Bonnet Buffer - rubber buffer at the bulkhead. This rubber buffer mounts at the bulkhead where the rear of the bonnet rests when closed, cushionin...

Sealing Washer used at sealing interfaces across multiple engine assembly groups. This washer is used in rocker cover and breather assemblies, val...

Front Brake Shoe Spring for the front drum brake assembly. This return spring connects the two brake shoes and pulls them back off the drum when th...

Axle Bump Stop - rubber bump stop for the front and rear suspension axle assemblies. Fitted to the chassis above each axle, the bump stop limits a...

Shackle Pin (9/16 UNF × 4-1/2 in.) for the leaf spring suspension on Land Rover Series vehicles. This medium-length pin is used at the forward (ch...

Brake Pipe Clip - single-bore retaining clip for securing a rigid brake pipe to the chassis or body structure. This clip holds the brake pipe in i...

Enhance the ignition performance of your Land Rover Defender, Discovery 1, and Range Rover Classic (3.5 V8 carb & EFI models) with this high-qu...

Plain Nut - 1/4" BSF hexagonal plain nut in the British Standard Fine (BSF) thread form. The BSF thread form uses a finer pitch than BSW (British ...

Thermostat - 88°C for the cooling system of V8 petrol engines. The thermostat regulates coolant flow between the engine block and the radiator, al...

Distributor Rotor Arm for the 3.5L V8 petrol ignition system. The rotor arm sits on top of the distributor shaft beneath the cap and rotates to dis...

Door Hinge for the rear end (load/tail) door, lower position. One of the pair of side-hinged door hinges that mount the rear door to the body aper...

Air Filter Element for the 3.5L V8 Twin Carb petrol engine air intake. This filter element is fitted in the air intake housing ahead of the carbur...

Fuel pump diesel 2.25

Sliding Window Catch for the front door sliding window assembly on Series Land Rover models. This black plastic catch secures the sliding window p...

Rear Mudflaps - a pair of rear mudflaps for the 88in short-wheelbase, fitted behind the rear wheels to deflect road spray and debris thrown up by t...

Wheel Cylinder Overhaul Kit for front drum brake systems fitted with 11-inch brake drums. This kit provides the necessary parts to overhaul all fo...

Oil seal

Lock Plate for the front axle assembly. This metal tab washer locks fastener heads in position by bending a tab against the bolt head or nut after...