Land Rover Defender New Parts

CuNiFer Brake Pipe, 3/16" outer diameter, supplied for the brake hydraulic circuit. The copper-nickel alloy resists corrosion and is soft enough to...

Split Pin used throughout the chassis, steering and driveline assemblies as a positive locking fastener. The pin is passed through a cross-drilled...

Nut for U-bolt M12

screw M5 x 12

Glass Fuse rated at 10A, a cartridge-type fuse used in the vehicle electrical system. The fuse seats in the fuse box or an inline fuse holder and ...

ATF - Dexron III is an automatic transmission fluid meeting the Dexron III specification, supplied in a 5 litre container. It is a hydraulic fluid...

Brake Cleaner & Degreaser - an acetone-free aerosol solvent cleaner for brake components and general parts cleaning. It removes dirt, grease, ...

Bolt - 1/2" UNF x 6-1/4", part of the front radius arm chassis mounting. The long shank passes through the radius arm front bush and the chassis m...

Drain/fill plug magnetic axle

Bolt - a threaded fastener used within the axle and suspension assembly. It secures front axle case mountings and rear suspension arm attachments,...

Hinge bolt Defender Torx

Spring Washer, M8, a split ring washer used with M8 bolts and nuts to prevent fastener loosening caused by vibration and cyclical loading. The spl...

Air Suspension Connector joins the valve block to a high-pressure air line within the air suspension pneumatic circuit. The fitting forms a sealed...

Wheel Spacer Set mounts between the wheel hub and the road wheel to increase track width, fitting over the hub and carrying a fresh set of studs fo...

Blind Rivet Pin is a plastic blind-rivet fastener, 9.4 mm head diameter by 13 mm long. It secures trim panels, covers and liners by expanding to g...

Diesel Exhaust Fluid (AdBlue) is a consumable fluid for the Selective Catalytic Reduction (SCR) exhaust aftertreatment system on diesel engines. I...

Cap bolt

Plain Washer M8

Hex Nut - M8 is a standard six-sided metric threaded fastener with an 8 mm nominal thread diameter. It threads onto a matching M8 bolt or stud to ...

Oil filter element for the engine lubrication system within the Oil Cooler and Filter assembly. This cartridge-type element removes particulate c...

Diff oil seal

Modular Steel Wheel is a heavy-duty 8-hole steel road wheel finished in satin black. Specification: 18 x 8 inch, ET45 offset, 5 x 120 PCD, rated t...

Plate Nut

Cable Tie, a push-fit strap for routing and securing wiring and hoses. The tie strap bundles and secures wiring looms, pipes and hoses, locating i...

Wheel Nut for securing an alloy road wheel to the hub. The nut clamps the wheel against the hub face on the wheel stud, maintaining correct seatin...

Hub Nut - M24 x 2.0 for wheel hub and bearing retention. This M24 x 2.0 metric hub nut secures the wheel hub or halfshaft flange onto the stub axl...

Exhaust Stud Nut for front exhaust system connections. This nut secures exhaust pipe sections to the manifold or downpipe studs, maintaining a gas...

Front Axle Housing Oil Seal seats in the front axle case where the drive shaft passes through the housing to the hub. It runs against the rotating...

Bolt with an external Torx head, M12 x 35 mm. Used to secure rear brake components at the disc and calliper mountings, and rear suspension fixings...

Suspension Arm Nut - M16 flanged nut used on the rear suspension. It secures the lateral and lower arm pivot bolts where they pass through the sus...

Key Fob Battery - CR2032 3V lithium button cell for Land Rover remote central locking handsets. Fits directly into the remote key fob housing. Rep...

Pinion Oil Seal for the rear differential, running on the drive pinion shaft. The seal sits where the pinion shaft enters the differential housing...

Rear Crankshaft Oil Seal for the 2.0L AJ200-series four-cylinder engine, in both petrol and diesel applications. Seals the rear of the crankshaft ...

Silicone Hose Kit Puma 2.4 - Defender - Blue

Check Strap

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Spring Nut is an M10 "U"-type spring-steel clip nut that provides a captive threaded fixing point on panels and brackets. The U-shaped clip slides...

Wheel Nut for securing an alloy road wheel to the hub. The nut clamps the wheel against the hub face on the wheel stud, maintaining correct seatin...

Hook & Loop Fastening Strap for securing and bundling loose items within the vehicle interior, cargo area, or workshop. The strap wraps around ...

Screw - a fastener used to secure exterior body panels and trim, including body mouldings, front and rear bumper assemblies, radiator grille panels...

Front Suspension Bolt - a mounting bolt used in the front suspension assembly, at the suspension arm and knuckle/hub mountings. It secures the joi...

Underbody Guards - 6mm Alloy for the Land Rover Defender (L663, 2020+). Manufactured from 6mm-thick aluminium alloy, these guards fit directly to ...

Rock Sliders with Tree Bars for the Land Rover Defender 110 and 130 (L663, 2020+). Constructed from steel box section and finished in black powder...

Timing Chain Kit for the Ingenium 2.0L 4-cylinder engine, covering the complete timing chain system. The Ingenium AJ200 engine uses a dual-chain a...

Plastic Washer - a plastic washer used at the radiator cowl (fan shroud) mounting in the cooling system. It sits under the fixing that secures the...

Knock Sensor mounts on the cylinder block and detects engine knock through block vibration. It reports combustion knock to the engine management s...