Land Rover Defender New Parts

Transmission Oil Cooler - heat exchanger in the automatic transmission cooling circuit, mounted in the front cooling pack alongside the radiator an...

Front Wheel Hub - hub and integrated wheel bearing unit for the front knuckle assembly. The hub carries the road wheel and brake disc and is drive...

Camshaft Sprocket is a timing drive gear in the valvetrain, mounted on the end of a camshaft. Driven by the timing chain from the crankshaft, it r...

Camshaft Sprocket for the timing drive of the 3.0L V6 supercharged (AJ126) and 5.0L V8 supercharged (AJ133) petrol engines. Driven by the timing c...

Air Suspension Levelling Valve - front valve block in the four-corner electronic air suspension circuit. It sits between the compressor and reserv...

Camshaft Sprocket for the camshaft drive, mounted on the end of the camshaft and driven by the timing chain from the crankshaft. It transmits the d...

Front Brake Pads are the friction elements of the front disc brake, clamped onto the brake disc by the caliper pistons to convert the vehicle's mom...

Brake Pad Kit - Front - front axle set of disc brake pads for the 19-inch front brake disc and caliper installation. The pads are clamped against ...

Front Lower Suspension Arm (wishbone) for the left-hand side of the front independent suspension, locating the lower end of the wheel knuckle again...

Front Brake Pad Kit - friction pad set for the front disc brake assembly, for the 380 mm front disc and size 20 caliper configuration. The pads lo...

Transmission Oil Pan for the ZF 8HP eight-speed automatic transmission. It bolts to the underside of the transmission case and retains the automati...

Oil Pump for the engine lubrication system of the supercharged petrol V6 and V8 (AJ133) engines. Driven from the crankshaft, the oil pump draws oi...

Vacuum Pump supplying the brake servo on the supercharged AJ133 petrol engines (3.0L V6 and 5.0L V8). Forced-induction petrol engines cannot rely ...

Fuel Pump is the in-tank pump module of the fuel delivery system. Mounted within the fuel tank, it draws fuel and delivers it under pressure to th...

Inlet Manifold for the 2.0L AJ200 Ingenium four-cylinder diesel engine. The manifold forms part of the air intake system, mounting to the cylinder...

Air Conditioning Condenser - front-mounted condenser for the air conditioning refrigerant circuit, specified for 3.0L AJ20P6 petrol and 3.0L AJ20D6...

Combined Oil and Vacuum Pump for the 2.0L Ingenium (AJ200) diesel engine. This tandem unit houses the engine oil pump and the vacuum pump in a sing...

Cooling Fan Motor in the engine cooling system, driving the radiator cooling fan. The motor spins the fan to draw air through the radiator, dissip...

Air Suspension Compressor The pump that generates and supplies compressed air to the four-corner electronic air suspension system. Driven by an el...

Air Suspension Compressor from the air supply unit of the four-corner electronic air suspension system. The compressor draws in ambient air, compr...

Trim Clip (Scrivet) is a two-piece plastic push-fit fastener used to secure trim panels, facia sections, splash shields and other clipped-in compon...

Washer - Sealing

Relay Black 2A 4 Pin

Fuel Pump Drive Control module within the fuel delivery system, governing operation of the in-tank fuel pump. The module receives a demand signal ...

Fuel Pump Drive Control module within the fuel delivery system, governing operation of the in-tank fuel pump. The module receives a demand signal ...

Purge Control Valve - evaporative emission (EVAP) control system. The valve sits in the line between the activated carbon canister and the engine ...

External Torx Head Bolt, M8 x 48 mm, for the front propshaft flange. The bolt clamps the front propshaft flange to its mating drive flange. Its ex...

Exhaust Clamp - 60mm exhaust joint clamp for the front section of the exhaust system, securing the downpipe to the centre silencer section. Clamps...

Clip is a fastening used within the body moulding assembly, retaining exterior trim and moulding panels against the bodywork.

Front Suspension Arm Bush - Inner Mount - the rubber-bonded pivot bush at the inner mounting point of the front suspension arm, within the front su...

Wheel Bearing - Rear, a component of the rear hub assembly. The rear wheel bearing carries the vehicle's rear load and allows the road wheel and h...

Bonnet Latch for the bonnet (hood) closure mechanism. It engages the bonnet striker to hold the bonnet closed and releases it when operated, formin...

Front Strut Boot Kit renews the protective gaiter and mounting hardware for a front air suspension strut, part of the four-corner air suspension sy...

Oil Filter - the replaceable cartridge element for the engine lubrication circuit, fitted inside the filter housing on the oil pump, cooler and fil...

Hub Nut - M24 x 2.0 for wheel hub and bearing retention. This M24 x 2.0 metric hub nut secures the wheel hub or halfshaft flange onto the stub axl...

Flanged Nut for use in Land Rover assembly applications. The integrated flange acts as a built-in load-spreading face, distributing clamping force ...

Screw and Washer - M5 x 20 is a self-tapping fastener with a captive washer, an M5 thread, 20 mm length and a hex head. It secures body panels, sp...