Land Rover Defender New Parts

Timing Chain Kit for the Ingenium 2.0L 4-cylinder engine, covering the complete timing chain system. The Ingenium AJ200 engine uses a dual-chain a...

Plastic Washer - a plastic washer used at the radiator cowl (fan shroud) mounting in the cooling system. It sits under the fixing that secures the...

Accessory Drive Idler Pulley

Kinetic Recovery Rope - vehicle recovery accessory for extracting a bogged or stuck vehicle. Unlike a static strap, a kinetic rope stretches under...

Cover Gasket for the crankcase cover, part of the emission-control and crankcase ventilation system on the 2.0L AJ200 four-cylinder diesel engine. ...

Thermostat Seal for the thermostat housing on AJ200/AJ20 series petrol and diesel engines. It seals the thermostat housing joint within the cooling...

EGR Outlet Gasket for the 2.0L four-cylinder diesel engine (AJ200), sealing the joint where the EGR valve outlet meets the inlet manifold. It main...

Idler Pulley for the front-end accessory belt drive, 90mm diameter. The idler routes and guides the auxiliary drive belt around the accessory pull...

Knock Sensor mounts on the cylinder block and detects engine knock through block vibration. It reports combustion knock to the engine management s...

Oil Cooler Gasket seals the oil cooler within the oil cooler and filter housing assembly. It maintains the oil-tight joint between the cooler and ...

Idler Pulley for the front-end accessory belt drive, 90mm diameter. The idler routes and guides the auxiliary drive belt around the accessory pull...

Gasket - Exhaust Manifold

Exhaust Gas Pressure Sensor for the 3.0L AJ20D6 Ingenium six-cylinder turbo diesel, operating within the exhaust gas recirculation and aftertreatme...

Injector Refit Kit supplying the seals needed to refit a fuel injector on petrol engines. It restores the sealing interface between the injector an...

Brake Pad Wear Wire - front brake pad wear warning wire within the braking system. Routed to the front brake pad, the wire completes a circuit tha...

Thermostat Seal for the thermostat housing on AJ200/AJ20 series petrol and diesel engines. It seals the thermostat housing joint within the cooling...

Fuel Injector Sealing Washer for the fuel injection system. Seals the fuel injector against the cylinder head, maintaining the combustion seal and...

Brake Pad Wear Wire - front brake pad wear warning wire within the braking system. Routed to the front brake pad, the wire completes a circuit tha...

Timing Chain Tensioner Arm bears against the timing chain within the timing drive assembly, providing the face through which the tensioner applies ...

Hex Head Bolt - M14 x 148mm fastener used at the front crossmember and stabiliser bar, front suspension arm, rear bumper and tow bar mountings. A ...

O-Ring sealing the variable valve timing (VVT) solenoid cover. Seals the VVT solenoid cover within the engine timing gear, preventing oil leakage ...

Guide - Timing Chain

Axle oil filler plug, sealing the combined fill and level aperture in the axle casing. Used at both front and rear axle positions. The plug closes...

Axle oil drain plug, sealing the drain aperture at the base of the axle casing. Used at both front and rear axle positions. The plug is removed to...

Exhaust System Screw, M8 x 20 mm. Used on exhaust and turbocharger joints - securing the catalytic converter to its mating pipe section, and at tu...

Nut and Washer Assembly is an M6 hexagonal nut supplied together with its washer as a single assembly. The washer spreads the clamping load across...

Wheel Bearing Circlip - 51 mm retaining ring for the wheel hub bearing. Seats in the groove of the knuckle bore and locates the hub bearing axiall...

Gearbox Plug

Blanking Plug - timing chain cover, supplied with its O-ring. Seals a machined service aperture in the timing chain cover of the Ingenium engine f...

Blanking Plug - timing chain cover, supplied with its O-ring. Seals a machined service aperture in the timing chain cover of the Ingenium engine f...

Interior fixing screw used throughout the instrument panel, floor console and interior trim assemblies. It secures trim panels, mounting brackets ...

Water Connection for the turbocharger coolant feed, lower position, in the turbocharger lubrication and cooling circuit of the 3.0L AJ20P6 Ingenium...

Connecting Tube running from the thermostat housing to the EGR cooler, part of the engine coolant circuit on the 2.0L Ingenium petrol engine and it...