Land Rover Defender New Parts

Wheel Spanner with a 27 mm socket, a hand tool for removing and refitting wheel nuts. Engages the 27 mm hexagon of the wheel nut to loosen or tigh...

Brake Hose Clip in the brake hydraulic circuit, securing a flexible brake hose to its mounting bracket where the hose crosses from the chassis to a...

Locking Flange Nut - M8 for fastening applications requiring vibration-resistant fixings. A prevailing-torque hexagonal nut with an integral flang...

Wheel Spanner - 24mm for removing and fitting wheel nuts on Land Rover vehicles. This 24mm spanner is sized for the standard wheel nut used across...

Relay is a 4-pin electromechanical switching relay used within the vehicle's electrical system. A low-current control signal energises the 12V coi...

Fuel return tube O-ring seal

LED Driving Light - round auxiliary driving light with a 4" (100mm) diameter housing and 50W LED output. Intended for external mounting as a suppl...

Valve - Control

Kinetic Recovery Rope - vehicle recovery accessory for extracting a bogged or stuck vehicle. Unlike a static strap, a kinetic rope stretches under...

EGR Outlet Gasket for the 2.0L four-cylinder diesel engine (AJ200), sealing the joint where the EGR valve outlet meets the inlet manifold. It main...

Spark Plug - ignition spark plug for Ingenium petrol engines (AJ20 / AJ22 series, including PHEV applications). The plug screws into the cylinder ...

Relay - 20 A five-pin micro relay, black housing. A five-pin relay is a changeover type: a low-current control circuit energises the coil, which s...

Accessory Drive Belt for the front end accessory drive of the 2.0L Ingenium four-cylinder engine (AJ200 / AJ20P4, petrol and diesel applications). ...

Mini Relay with four blade terminals, rated at 70 amp, grey housing. A four-terminal mini relay switches a single normally-open high-current circu...

EGR Inlet Gasket for the 2.0L AJ200 Ingenium diesel Exhaust Gas Recirculation system. Seals the inlet joint of the EGR assembly to maintain a gas-...

O-Ring is a 60mm sealing ring used in the Exhaust Gas Recirculation (EGR) circuit of the 2.0L four-cylinder diesel engine (AJ200 / AJ20D4 family). ...

O-Ring for the Exhaust Gas Recirculation (EGR) circuit. This seal maintains a gas-tight joint within the EGR section, sealing the connection betwe...

Front Crankshaft Oil Seal for the AJ200 2.0L four-cylinder petrol and diesel engine. It seals the front of the crankshaft where it passes through t...

Clip is a fastening used within the body moulding assembly, retaining exterior trim and moulding panels against the bodywork.

Gasket - Exhaust Manifold

O-Ring for the oil filter and cooler assembly. It seals a connection within the oil cooler and filter assembly, maintaining oil-tight integrity at...

Sealing Ring sealing a joint within the engine timing gear covers. This O-ring seals a connection at the timing cover assembly, maintaining oil-ti...

Bolt securing the fuel injector and high-pressure fuel pipe assembly on the engine fuel system. It clamps the injector and high-pressure pipe unio...

Oil Drain Plug for the engine oil pan (sump). Threaded into the base of the oil pan, it seals the oil drain point and is removed to drain the engi...

Magnetic Oil Drain Plug - M14 x 21 sump drain plug in the engine lubrication system. The plug seals the drain aperture in the oil sump and is remo...

Body Moulding Retainer Clip, a lantern-type fastener for the vehicle's exterior trim. The clip secures exterior body mouldings - such as the rocke...

Ignition Coil for the 2.0L four-cylinder petrol engine (AJ200 / AJ20P4, including PHEV). This is a coil-on-plug unit that mounts directly on the sp...

Hub Bearing

Brake Caliper Guide Pin Dust Cover for the front and rear brake calipers. The boot fits over the caliper guide pin and seals against the carrier b...

Brake Caliper Bleed Screw for the front and rear brake calipers. The bleed screw threads into the bleed port on the caliper body and is opened to ...

Piston - 0.50 mm Oversize for the 2.0-litre Ingenium (AJ200D / 204DTD) diesel engine. An engine-rebuild piston machined 0.50 mm over the standard ...

Hood Latch for the bonnet closing mechanism. The latch is body-mounted and engages the bonnet striker to hold the bonnet shut, releasing when the ...

Oil Cooler, part of the engine lubrication system. It draws heat out of the engine oil to hold oil temperature within its operating range under su...

Camshaft Sprocket is a timing-drive gear in the valve train of the 2.0L Ingenium diesel engine (AJ200D). Mounted on the end of the camshaft, it is...

Dust Cap for a brake bleed nipple. This small protective cover fits over the bleed screw on a brake caliper or wheel cylinder. It keeps dirt and m...

Piston Ring Set in standard size for the Ingenium AJ200D / 204DTD 2.0L 4-cylinder diesel engine. The rings seal the combustion chamber against the...

Piston in standard size for the Ingenium AJ200D / 204DTD 2.0L 4-cylinder diesel engine. The piston runs in the cylinder bore and transfers combust...

Connecting Rod for the Ingenium 2.0L engine (AJ200 / AJ204) in the 240 hp output variant. The connecting rod links the piston gudgeon pin to the c...

Connecting Rod for the Ingenium 2.0L engine (AJ200 / AJ204) in the 180 hp output variant. The connecting rod links the piston gudgeon pin to the c...