Land Rover Defender New Parts

Spark plug for the ignition system of the Ingenium petrol engine range - 1.5L AJ20P3, 2.0L AJ20P4 / AJ200P and 3.0L AJ20P6 / AJ22P6, including plug...

DEF Injector Refit Kit

Coolant Expansion Tank Cap - pressurised filler cap for the coolant expansion and overflow container in the engine cooling system. The cap sets th...

Variable Timing Solenoid - camshaft timing oil control valve in the variable valve timing system of the Ingenium engine range. The solenoid is an ...

V-Belt for the front-end accessory drive of the 3.0L AJ20P6 six-cylinder petrol engine. The belt is driven by the crankshaft pulley and transmits ...

Outer front door finisher from the front door exterior trim assembly, fitted to the outer face of the front door panel. The finisher forms the ext...

Outer front door finisher from the front door exterior trim assembly, fitted to the outer face of the front door panel. The finisher forms the ext...

Expansion Chamber from the air supply unit of the four-corner electronic air suspension system. The chamber is plumbed to the compressor and acts ...

Brake Pad Wear Sensor for the front axle, part of the brake pad wear warning circuit. The sensor is located in the brake pad and carries a wire lo...

Rear Crankshaft Oil Seal - the main oil seal at the flywheel end of the crankshaft, part of the crankshaft sealing arrangement on the Ingenium engi...

Drive Belt - ISG - V-belt in the front-end accessory drive of the 3.0L Ingenium six-cylinder petrol engine, driving the belt-integrated starter gen...

Oil Filter Element & Gasket Kit

Coolant Expansion Tank Cap - pressure cap sealing the coolant expansion (overflow) container in the engine cooling circuit. The cap is a working c...

Spark Plug - ignition component for the 4.4L V8 Turbo Petrol engine. The plug threads into the cylinder head and carries the high-voltage discharg...

Accessory Drive Belt for the front end accessory drive of the 2.0L Ingenium four-cylinder engine (AJ200 / AJ20P4, petrol and diesel applications). ...

EGR Inlet Gasket for the exhaust gas recirculation circuit of the 2.0L I4 AJ200 Ingenium diesel engine. The gasket seals the EGR inlet joint on th...

Timing Gear Special Nut from the front timing gear assembly, securing the lower primary timing chain guide. The nut locates and clamps the guide a...

Timing Cover Blanking Plug - threaded plug that closes an aperture in the front timing cover of the 2.0L Ingenium petrol engine (AJ200 / AJ20P4, al...

O-Ring - VVT Solenoid Cover, 47 mm, sealing the variable valve timing solenoid cover to the cylinder head on Ingenium engines - 2.0L AJ20P and AJ20...

Coolant outlet tube forming the water outlet connection at the cylinder head, in the engine cooling circuit of the 2.0L I4 AJ200 Ingenium petrol en...

Cable Connector - an electrical connector used in the vehicle wiring harness. The connector forms the termination between a harness cable and its ...

Bolt - hex-head bolt with washer, used in the splash and heat shield assembly. It secures the underbody splash shields and powertrain undertray pa...

Oil Filter Element for the 3.0L AJ20 / AJ22 Ingenium six-cylinder engine, fitted in the engine lubrication circuit. The cartridge element seats in...

Mini Relay with four blade terminals, rated at 40 amp. A four-terminal mini relay switches a single normally-open high-current circuit under the c...

Mini Relay with four blade terminals, rated at 70 amp, grey housing. A four-terminal mini relay switches a single normally-open high-current circu...

Coolant Bleed Hose - small-bore hose in the engine cooling system, running from the cylinder head bleed point to the coolant expansion tank. It ve...

Camshaft Cover Gasket - moulded gasket sealing the camshaft cover to the cylinder head. It seals the valve train and cam carrier area against oil ...

Valve stem seal for the cylinder head valve train. The seal locates on the valve guide and wipes the valve stem as it reciprocates, metering the s...

Timing Chain Guide, Lower Primary from the front timing gear assembly. It bears against the primary drive chain on the run between the crankshaft ...

Exhaust Clamp for the 2.0L Ingenium diesel exhaust system (AJ200D / AJ20D4). The clamp secures the front section joint of the exhaust, holding the...

Oil Filter Element for the 3.0L AJ20 / AJ22 Ingenium six-cylinder engine, fitted in the engine lubrication circuit. The cartridge element seats in...

Bolt - interior trim fixing bolt from the instrument panel and floor console fastener group. It secures instrument panel mountings, the floor cons...

Wheel Centre Cap - hub cover for modular steel road wheels. It press-fits into the centre bore of the wheel, covering the hub flange and keeping d...

Seal - Oil

Timing Gear Bolt - special-form fastener used in the timing drive assembly at the front of the Ingenium petrol engine. It is one of the fixings th...

PCV Valve Service Kit

PCV Valve Service Kit - service parts for the positive crankcase ventilation valve, which sits in the crankcase emission control system on the cyli...

Air Filter Element from the engine air intake system, seated in the airbox between the intake duct and the induction tract. Traps airborne dust an...

Turbocharger Coolant Hose from the engine cooling circuit, serving the turbocharger on the 3.0L AJ20P6 petrol engine. The hose carries engine cool...

O-Ring - seals a joint in the thermostat housing and EGR cooling circuit. Fitted to the 2.0L four-cylinder AJ200 diesel engine, it maintains a lea...

Coolant Tube forming the primary coolant path between the cylinder block and the water outlet. This aluminium tube carries coolant from the engine...

Exhaust Pipe Gasket seals the front flanged joint of the exhaust system, maintaining a gas-tight connection and preventing exhaust leakage at the j...