Price <10

Master Cylinder to Pedal Box Gasket for the hydraulic clutch circuit. This gasket seals the mounting face between the clutch master cylinder body ...

Oil Pump Gasket for the Rover V8 petrol engine lubrication system. This gasket seals the oil pump to its mating face, maintaining oil pressure and...

Escutcheon Seal for the exterior door handle escutcheon. The seal sits between the lock barrel and the outer door skin, sealing the aperture where...

Water Pump Gasket - 7-Hole for the cooling system on Land Rover 4-cylinder military engines. This gasket seals the mating face between the water p...

Injector Sealing Washer seals the base of the fuel injector into the cylinder head on the Td5 2.5L 5-cylinder turbo diesel engine. The washer sits...

Accelerator Pedal Lever Pad is the moulded rubber pad that fits over the accelerator pedal lever. It provides the contact face between the driver's...

Pedal Pin is the pivot pin in the pedal box assembly that locates the brake and clutch pedals. It passes through the pedal boss and the pedal moun...

Fir Tree Fastener push-in fixing in grey, used to retain headlining, roof trim and similar interior and exterior trim panels. The tapered fir-tree...

Screw – a No. 6 × 1/2 in self-tapping screw used to secure interior trim and panel fixings, such as the instrument binnacle, fascia mouldings and a...

Choke Clip is the retaining clip that secures the choke cable at the Zenith carburettor. Part of the choke cable installation, it anchors the oute...

O-Ring for the power steering hydraulic circuit, sealing a connection within the pressurised steering fluid system. This is the brown, thick-secti...

Rubber Plug Cushion is a moulded rubber blanking plug that fits into a pre-formed aperture in the body, frame or seat base to close off the opening...

Jubilee Clip - 21-44mm is a worm-drive hose clip with a 21-44mm clamping range. The band is tightened by a captive worm screw to clamp small- to m...

Door Latch Linkage Clip for the door latch and lock assembly. It retains the operating rod on the latch mechanism. The clip holds the handle-to-la...

Locknut for body and trim panel fixings. It seats into a pre-formed aperture in the panel to provide a captive threaded point for the screws or bo...

Steering Rocker Shaft Bush - a bearing bush within the steering relay assembly. The bush locates and supports the rocker (relay) shaft inside the ...

O-Ring for the power steering hydraulic circuit, sealing the high-pressure pipe connection to the power steering box. This is the brown, thin-sect...

Shakeproof Washer – a serrated, externally toothed lock washer used at the clutch hydraulic hose union. The teeth bite into both the mating surfac...

Cable Grommet for the wiring loom, fitting a 41.5 mm panel hole and accepting a cable of up to 6 mm. Made of black rubber, it lines the hole where...

Decal

A-Pillar Trim Clip A retaining clip used in the interior A-pillar trim assembly. It secures the A-pillar trim panel to the body structure alongsid...

Lucar Connector - a fully insulated two-way in-line electrical connector for joining wiring within the loom. Of the Lucar (blade) terminal type, i...

Front Door Glass Guide channels the window glass as it travels within the front door. This run guide locates the edge of the door glass and keeps ...

Brake Pipe Clip - a single moulded plastic clip that secures a brake pipe to the chassis within the braking hydraulic circuit. It retains the rigi...

Bonnet Grommet is a rubber grommet fitted within the bonnet assembly. It lines the aperture through which the bonnet prop rod or release mechanism...

Split Pin used to secure the accelerator cable and hand throttle cable connections, retaining the clevis pin at the cable-to-linkage joint. After ...

Spire Nut - a spring U-type nut that slides over a panel edge to receive a self-tapping screw. It provides a captive threaded seat where there is ...

Turbo Drain Gasket for the Td5 turbocharger oil drain. The gasket seals the joint where the oil return (drain) pipe meets the underside of the tur...

O-Ring for the power steering hydraulic circuit, sealing the low-pressure pipe connection to the power steering box. This is the green, thick-sect...

Flasher Lamp Lens - Sparto Type is the replaceable coloured lens for the Sparto-pattern direction indicator (flasher) lamp, forming part of the ext...

Brake & Clutch Pedal Bush for the pedal box assembly. It forms the pivot bearing where the pedals mount on their shaft, locating the brake and ...

double washer, restrictor

Spring Washer is an M8 double-coil spring washer used as a fastening component in body and chassis assemblies. The double-coil spring form maintai...

O-ring

Rivet is a permanent mechanical fastener used in the lower tailboard (drop-down tailgate) hinge assembly. Set through the hinge components, it for...

Blanking Plug for closing an unused 13 mm (1/2") hole in body or trim panelling. A push-in plastic plug used to blank off redundant or open apertu...

Washer A copper joint sealing washer for the oil filter housing, part of the engine lubrication system. It seals the oil plug or the oil filter ad...

Oil Pump Sealing Washer, part of the engine lubrication circuit at the oil pump. The washer forms a static seal at the oil pump joint, preventing ...

Bolt - an imperial hexagon-head bolt with a 5/16" UNF thread and a 3-1/4" shank length. This long-shank bolt is used at the alternator mounting on...

Engine Lifting Bracket bolts to the cylinder head and provides a rated attachment point for hoisting the engine. Fitted to the four-cylinder petro...

Oil Filler Pipe Gasket seals the joint between the oil filler pipe and the engine front (timing) cover. Fitted at the filler pipe mounting flange,...

Gear Change Selector Shaft Spring A spring for the gearbox gear-change selector mechanism. It acts on the selector shaft to provide the spring loa...

Set Screw - a fully threaded hexagonal-head setscrew with a 3/8" UNC (Unified Coarse) imperial thread and a 7/8" length. Used as a Rover V8 engine-...

Headlamp Screw is a fastener used in the front headlamp assembly. It secures the headlamp unit and rim within their mounting, holding the lamp in ...

Thermostat Housing Gasket seals the thermostat housing (water outlet elbow) to the intake manifold on the 3.5L carburettor V8 engine. It sits in t...

Gear Lever Retaining Plate for the gear lever turret on the LT76 manual gearbox. The plate bolts over the base of the gear lever to retain it in i...

Window Regulator Escutcheon - Front Door

Breather Filter is the crankcase ventilation filter mounted at the rocker cover on the V8 EFI petrol engine. It filters oil vapour and mist from t...