Price <10

Bolt for the floor-mounted gear change assembly of the ZF 6-speed automatic transmission. It secures the gear change mechanism to its mounting on ...

Retaining Clip for the output shaft oil seal on the MT82 6-speed manual gearbox. The clip locates and secures the oil seal within the gearbox hous...

Axle oil drain plug, sealing the drain aperture at the base of the axle casing. Used at both front and rear axle positions. The plug is removed to...

Axle oil filler plug, sealing the combined fill and level aperture in the axle casing. Used at both front and rear axle positions. The plug closes...

Exhaust Manifold Gasket that seals the exhaust manifold to the cylinder head on the 2.2L diesel engine. The gasket maintains a gas-tight joint bet...

Hex Head Bolt securing the timing belt idler pulley at the lower timing gear of the 3.0L V6 diesel engine. This is a single fixing bolt for the id...

Screw - M6 x 65mm threaded fastener. Factory-specified fixing screw with a 6mm (M6) thread and 65mm length.

Wiper Arm Cap - the hinged plastic cover that clips over the windscreen wiper arm at the spindle. It conceals and protects the arm-to-spindle reta...

Roof Assembly Seal for the body weather-sealing system. This seal fits at the roof assembly, forming the weather seal between the roof panel and t...

O-Ring seals a connection joint in the front air conditioning refrigerant circuit. It maintains the pressure-tight seal between refrigerant lines o...

A-Pillar Clip secures the A-pillar interior trim moulding to the body. It is a push-fit retaining clip that holds the plastic A-pillar cover again...

Bolt - Hex Head

Bolt

O-Ring

Retainer and Nut - an M10 nut and its retainer used at the front crossmember mounting. The retainer locates and holds the captive nut in position ...

Torque Converter Screw for the automatic transmission drive coupling. This fixing secures the torque converter to the drive plate, transmitting en...

Nut - a fixing nut used at the turbocharger and exhaust manifold joint. It retains the turbocharger to the exhaust manifold, a high-temperature jo...

Hex Head Bolt and Washer - a hexagon-head bolt supplied with a washer. A general-purpose fixing used at multiple mounting locations, including the...

Exhaust Manifold Bolt secures the exhaust manifold to the cylinder head. For 3.0L supercharged V6 and 5.0L V8 petrol applications.

Retaining Clip - a push-fit fastener used to secure exterior and interior trim mouldings and finishers to the body. The clip pushes into a locatin...

Wiper Arm Cap - a trim cover for the windscreen wiper arm spindle. Conceals and protects the wiper arm retaining nut at the base of the front wipe...

Retaining Clip - a fastener for exterior body mouldings and side-step trim. Secures body moulding and side-step trim panels to the bodywork.

Fuel Injector Sealing Washer for diesel injector installations. The washer seals the fuel injector against its seat in the cylinder head, containi...

Turbocharger Oil Return Hose Gasket for the 2.0L Si4 TIVCT petrol turbo engine. It seals the joint at the turbocharger oil return (drain) hose, al...

Fuel Injector Clamp Bolt for the 2.2L 16-valve turbo diesel four-cylinder (Puma) engine. It secures the injector hold-down clamp that retains a fu...

Body Moulding Retainer Clip, a lantern-type fastener for the vehicle's exterior trim. The clip secures exterior body mouldings - such as the rocke...

Trim Clip - a plastic push-fit retaining clip used to secure exterior trim and body mouldings to the vehicle. It locates in a pre-drilled panel hol...

Plastic Rivet is a push-fit fastener that secures front engine-compartment insulation panels to the body. It locates into a pre-formed panel hole t...

Parcel Shelf Strap Button is the pivot fixing that anchors the parcel shelf support strap in the load compartment. The support strap lifts the par...

Timing Gear Bolt for the 2.0L 16V petrol engine. It secures a gear on the engine's timing drive.

Valve Spring Retainer for the 2.0L 16-valve turbocharged petrol engine, fitted in the cylinder head valve train. The retainer caps the top of the ...

Engine Mounting Bolt with hexagonal head, M12 x 112 mm. A structural fastener securing the engine mounting to the subframe; the same bolt is also ...

O-Ring sealing the thermostat housing in the engine cooling circuit. Seats between the thermostat housing and its mating face to seal the coolant ...

EGR Inlet Gasket for the 4.4L DOHC DITC V8 diesel (TDV8). Seals the inlet joint of the exhaust gas recirculation (EGR) circuit, between the exhaus...