Price <10

Floor Pan Blanking Plug. It closes an unused aperture in the floor pan, sealing the opening against water, dust and road debris.

Plastic Drive Rivet - Wheel Arch Trim secures exterior trim panels to the body as part of the wheel arch trim fixing set. This one-piece expanding...

Washer for the bonnet insulation pad. This washer retains the sound- and heat-insulation pad against the underside of the bonnet, holding the pad ...

Screw - a threaded fastener used across several exterior body fixings. It secures fittings within the radiator grille, the rear end door seals and...

Self-Tapping Screw for body and trim fixing applications. Used to secure window surrounds, bodyside trim, facia and switch panels. The self-tappin...

Brake Pipe Clip - Double secures and routes rigid hydraulic brake pipes within the braking system. This double clip retains two brake pipes at a s...

Cylinder Head Bolt Washer seats under the head of a 7/16in cylinder head bolt on the Rover V8 petrol engine. It distributes clamping load across t...

Radiator Mounting Bush is the rubber isolation bush that secures the radiator to the body or chassis mounting points, preventing direct metal-to-me...

Cable Clip for securing the body wiring harness, part of the vehicle electrical system. This clip retains a cable run against the body or chassis,...

Grommet - Valve Cover

Valve Cover Grommet for the AJ-V8 petrol engine. It seals the cylinder head (valve) cover where a component passes through it, preventing oil escap...

Gasket

Thermostat Housing Gasket in the engine cooling system. This 37 mm gasket seals the joint between the thermostat housing and the engine on AJ-V8 4...

Thermostat Housing Seal for the engine cooling system, sealing the thermostat housing joint. Fitted between the thermostat housing and its mating ...

Coolant Outlet Gasket for the engine cooling system, sealing the coolant outlet flange where it joins the engine on V8 applications. The gasket fo...

Bush

Grommet - Blanking Plug, Gearbox Tunnel for Land Rover Series II and III. This small rubber blanking plug fits into an aperture in the top of the ...

Exhaust Manifold Stud for TDV6 2.7 and 3.0 and TDV8 3.6 diesel engines, used to fasten the exhaust manifold to the cylinder head. On 2.7 TDV6 engi...

Thermostat Housing Gasket for the 2.7L TDV6 diesel engine. This gasket seals the thermostat housing (water outlet) to the engine, preventing coola...

Thermostat O-Ring for the TDV6 diesel engine. This O-ring provides the coolant seal at the thermostat housing on TDV6 diesel engines, preventing c...

Oil Tube Gasket seals the turbocharger oil drain (return) pipe where it joins the engine, within the turbocharger lubrication circuit. After lubri...

Bolt - Exhaust Manifold & EGR - a fixing bolt used in the exhaust manifold and exhaust gas recirculation (EGR) assembly of the TDV6/TDV8 diesel...

Clamp - Tube

Camshaft Seal for the TDV6 2.7L V6 diesel engine. Seals the camshaft at its exit point from the cylinder head, preventing oil leakage from the cams...

Valve Stem Seal for the cylinder head valve train, fitting over the valve stem at the top of the valve guide. The seal meters lubrication down the...

Differential Pinion Shim - 0.062" selective shim used to set the pinion position within the differential (final drive) assembly. Fitted at the pin...

Oil Cooler Pipe Seal for the transmission oil cooler circuit. The seal fits at the oil cooler pipe union, sealing the connection against fluid lea...

Sealing Washer - 18 mm OD x 12 mm ID is a sealing washer with a 12 mm inner diameter and an 18 mm outer diameter, used to seal threaded unions and ...

Alternator Brush Set - the carbon brushes for the alternator, part of the charging circuit. The brushes bear on the rotor slip rings to carry field...

Cooling Turbo Gasket

Bolt for securing the steering box to the chassis on the Defender. Fits the manual Gemmer recirculating-ball steering box in non-power-assisted st...

bracket 390384

Screw for the valve rocker (rocker shaft) assembly of the VM 2.4L and 2.5L 4-cylinder turbo diesel engine. Retains the rocker gear on the cylinder...

Bolt - Hexagon Head used in engine and interior fascia assembly applications. This hexagon head fastener is used in the EGR system assembly and in...

Flanged Nut for use in Land Rover assembly applications. The integrated flange acts as a built-in load-spreading face, distributing clamping force ...

Banjo Bolt for diesel fuel pipe connections at the fuel filter. This hollow bolt secures a banjo union to its port, allowing fuel to pass through ...

Blanking Plate - moulded plug that closes an unused switch aperture in the facia or switch console. Where a vehicle is built without an optional s...