Price <10

Tab Washer for the steering box drop arm retaining nut. This lock washer sits under the nut on the steering box output shaft. Once the nut is torq...

Side Window Insert Spring Tensioning spring for the sliding side window insert in the two-door body's side window assembly. It provides the retain...

Self Levelling Unit Spring Ring

Accelerator Control Rod is a linkage rod that connects the accelerator pedal mechanism to the throttle shaft in the engine bay of Series II, Series...

Bolt - a hexagonal-head bolt with a 5/16" UNC (Unified Coarse) imperial thread and a 3/4" length. Used as an engine-assembly fixing, including cams...

Brake Shoe Screw - a retaining screw within the drum brake assembly that secures the brake shoe in position. It holds the shoe located against the...

O-Ring for the power steering hydraulic circuit, sealing a connection within the pressurised steering fluid system. This is the green, thin-sectio...

Clevis Pin for the front door hinge and check strap assembly. This pin secures the door check strap (travel limiter) at its pivot, retaining the s...

Door Latch Link Clip secures the operating link rod within the door latch and locking assembly. It retains the connecting linkage that transfers m...

Bolt - M8 x 50 - Torx is an M8 threaded fastener, 50 mm long, with a Torx drive head. It is used as a general-purpose fixing across a range of bod...

Plenum to Water Jacket Gasket seals the joint between the plenum chamber and the water-jacketed intake manifold in the Rover V8 EFI induction syste...

Centre Handle Cover is the screw cover cap for the window winder handle, finished in black. This small cover conceals the retaining screw on the m...

Bolt and Washer - an M8 x 24mm bolt supplied with a washer, used as a general-purpose fixing across several Land Rover assemblies. The washer spre...

Edge Clip - push-on edge clip that grips the flange of an interior trim panel, retaining both the panel and the wiring harness routed along its edg...

Speaker Bezel is the trim surround that frames a speaker opening in the interior. Part of the in-car entertainment (ICE) installation, it finishes...

Fan Belt - V-belt for the 2.6L 6-cylinder engine, driving the cooling fan and compressor. Fitted to the accessory drive system of the 2.6L engine....

Grommet / Blanking Plug - Dash Bulkhead for Land Rover Defender. This rubber plug seals an unused aperture in the dash bulkhead (such as a heater ...

Coolant Hose for the V8 carburettor petrol engine cooling circuit. It carries engine coolant between components of the cooling system, moulded to s...

Dowel is a precision locating pin used to align mating components in the drivetrain, such as the bell housing, gearbox casing and flywheel or drive...

Locking Washer of the Starlock (shakeproof) type, a push-on retainer used to hold a component onto a plain shaft or to lock a fastener against vibr...

Clip is a retaining clip in the front windscreen wiper linkage. It secures the wiper motor and linkage assembly, holding the linkage components to...

Exhaust manifold stud

Screw is an M4 x 8mm fastener used in the door mirror assembly, securing components of the interior and exterior mirrors at their mounting points. ...

Lock Washer secures the retaining hardware on the layshaft (countershaft) within the manual gearbox. A tab on the washer is folded against the ret...

Bolt - M6 x 30mm is a metric threaded fastener with a 6 mm nominal thread diameter and a 30 mm shank length. It secures bolted joints where an M6 ...

Screw – a black self-tapping screw with a pan head and Pozidriv drive recess, size No. 10 × 5/8 in, used to secure body, trim and panel fixings. B...

Washer - Diesel Sedimentor is a sealing washer used in the diesel fuel sedimentor (fuel filter/water separator) assembly on diesel-engined Land Rov...

Copper Sealing Washer, 7/16 inch, for hydraulic pipe unions on Series Land Rovers. This annealed copper washer seats under a banjo bolt or pipe un...

Core Plug - Cylinder Head A 7/8" diameter core plug (welch/expansion plug) that seals a casting core hole in the cylinder head. It closes the open...

Circlip - LT77 Selector Shaft for the LT77 5-speed manual gearbox. This circlip retains the selector shaft within the gear selector and shaft asse...

O-Ring for the air conditioning hose circuit. This O-ring seals connections within the air conditioning pipework, preventing refrigerant loss at p...

Saddle Clip for routing and securing the power steering pipes. This saddle-shaped clip clamps the power steering hydraulic pipes to the chassis or...

G-Hook - a hook fitting for the soft top drain channel. It anchors and tensions the drain channel that runs along the soft top, holding the channe...

Gearbox Top Cover Plate - the cover plate that closes the top aperture of the main gearbox casing. It seals the top of the gearbox over the select...

Cable Tie for securing wiring harnesses and cable runs throughout the vehicle.

Amber Switch Bulb for the heated windscreen and auxiliary switches. This small bulb provides the amber illumination within the switch, lighting th...

Main Bearing Cap Bolt - a 1/2" UNC bolt that fastens a main bearing cap to the cylinder block on the Rover V8 engine. It clamps the main bearing c...

Carpet Drive Fastener is a trim fastener used within the interior floor carpet assembly to secure the carpet to the floor. The fastener is driven ...

Self-Tapping Screw - an exterior body trim fastener. It secures the protective rubbing strip (side moulding) to the rear quarter panel, cutting it...

Circlip for the handbrake (parking brake) linkage. This external retaining circlip secures the handbrake relay elbow onto its pivot post, holding t...

Plain Washer is a flat fastening washer fitted under a bolt head or nut to spread the clamping load across a wider area and protect the mating surf...

Rear Lamp Bulb Holder Double-pole bulb holder that seats in the rear lamp housing, retaining the bulb and carrying the electrical contacts between ...

Washer - a general-purpose fixing washer used across multiple body, brake and chassis assemblies. It spreads the clamping load of a bolt or nut ov...

Amber Military Glass Indicator Lens - Used

Fuel Filler Seal - sealing ring fitted at the fuel filler, part of the fuel tank filler assembly. Seals the joint at the filler neck to prevent fu...

Clip - a retaining clip used to secure finisher mouldings and column shroud panels to their supporting structure. It locates and holds the mouldin...

Grommet - rubber sealing grommet, 3/4 inch overall diameter with 1/8 inch centre hole. Used to seal and protect wiring cables where they pass thro...

Engine Stud for the Rover V8 petrol engine, measuring 5/16" x 2-1/8" with a UNC/UNF dual thread form. The coarse UNC end threads into the engine c...