Price <10

Tensioner Cup is a component of the timing chain tensioner assembly on the 2.0L L-Series 8-valve diesel engine. It seats within the tensioner mech...

Air Suspension Compressor Screw is a fastener used within the air suspension compressor assembly. It secures components of the Hitachi compressor ...

Air Suspension Compressor Screw is a fixing used in the air suspension compressor assembly. It retains the compressor's housing and mounting compo...

Catalytic Converter Gasket for the exhaust system. The gasket seals the flanged joint between the catalytic converter and the adjoining exhaust sec...

Body Mount Washer is a load-spreading washer used at the body-to-chassis mountings. It sits under the body mount fixing to distribute the clamp lo...

Gearchange Rod Pin is a pivot pin used in the gearchange rod assembly of the manual gearbox shift linkage. It locates and retains the gearchange r...

M5 Bolt for the transfer box assembly. This fastener secures components within the transfer box and its gear change rod (selector) linkage on manua...

Forming Thread Screw is an M6 thread-forming screw. As it is driven into an unthreaded pilot hole, it displaces material to form a matching female...

Monobolt Rivet - 1/4" structural blind rivet for body and chassis fastening. The Monobolt is a high-strength blind rivet set from one side of the ...

Carburettor Top Cover Screw for the Zenith 36 IV carburettor. The screw secures the top cover to the carburettor body, clamping the cover and its ...

Buffer stop for the rear end door. Cushions the door against the body on the hinge side, limiting travel and preventing metal-to-metal contact.

Bolt - UNF - Tail Light is a Unified National Fine (UNF) fastener used in the rear lamp assembly on Defender models built up to VIN LA939975. This...

Air Cleaner Mounting Rubber for the engine air intake system. This flexible rubber mount locates and supports the air cleaner (air filter) housing...

Handbrake Adjusting Knob threaded adjuster fitted to the parking brake (handbrake) lever assembly. The knob threads onto the end of the handbrake ...

Chassis Frame Washer is a load-spreading washer used in the chassis frame fastening assembly. It seats under a bolt head or nut to distribute clamp...

Fusible Link

EGR Valve Gasket seals the exhaust gas recirculation valve joint on the Td5 2.5L 5-cylinder turbo diesel. It sits between the EGR valve and its ma...

Dowel for the manual gearbox gear-selector assembly. It locates the selector components against the housing to hold their alignment during gear eng...

Screw

Main Spring is the spring fitted within Superwinch free-wheeling (manual locking) front hubs. A free-wheeling hub allows the front wheels to be di...

Diode used in the vehicle's electrical system. A diode conducts current in one direction only. In the wiring it is used to protect circuits and to...

O-Ring, 19mm, sealing a pipe union within the engine cooling and exhaust gas recirculation (EGR) circuits. The O-ring forms a leak-tight seal at a...

Blanking Plug closes off an unused aperture in the front bumper and chassis under-ride protection bar. Pushed into an open hole to seal it, the pl...

Fuel Injector O-Ring for V8 petrol applications. The sealing ring at the fuel injector within the fuel injection system. It maintains a leak-tight...

Roof Rail Front Gasket, the sealing gasket fitted at the front of the roof side rail. It seats between the side rail and the roof panel, sealing t...

Valve Stem Oil Seal seats on the valve guide within the cylinder head valvetrain, sealing the point where the valve stem passes through the guide. ...

Copper Washer for the inlet manifold on the 1.8L K-Series four-cylinder petrol engine. The soft copper ring deforms under clamping load to form a ...

brake kit master CB type 503754

Rear Body Capping Corner, a body trim finisher fitted to the top edge of the rear body. This corner section caps the exposed top edge of the body ...

Rivet - a blind body and trim fastener used throughout the vehicle's panel and bracket fixing points. It forms a permanent riveted joint where pan...

Thermostat Blanking Cap seals an unused coolant outlet on the thermostat housing within the K-Series cooling circuit. Fitted to the 1.8L 4-cylinde...

Flanged Bolt is an M12 x 40 mm fastener with an integral flanged head that distributes clamping load across the joint without a separate washer. U...

Tow Equipment Bolt is an M10 x 115 mm fastener used to mount rear towing equipment, such as a drop plate with tow ball or a rear towing step, to th...