Price <10

Rod retaining

Bolt for the drive shaft assembly on the Discovery 1 and Range Rover Classic. Used to secure the drive shaft flange connections in both ABS and no...

Seat Recline Handle for the front seat backrest (squab) manual recline mechanism. This handwheel mounts on the outboard side of the seat frame and...

Door Lock Circlip - retaining clip for the rear end door lock. This circlip secures a component of the rear door lock mechanism, holding it on its...

Clip securing the operating link within the tail door lock mechanism. The clip retains the lock link (rod) that connects the latch to the lock act...

Power Steering Hose O-Ring is a sealing ring in the power steering hydraulic circuit. It seals the union between a power steering hose and its mat...

Door Lock & Handle Retaining Clip - securing clip within the exterior door handle and lock assembly. This clip retains the door lock and handl...

Coolant Hose connecting the engine to the heater control valve. Part of the heater coolant circuit, it carries hot coolant from the engine to the ...

Radiator Hose Clip secures a coolant hose within the engine cooling system, clamping the hose onto its radiator or engine connection to maintain a ...

Bolt for the outer body panels, securing the wheelarch and front valance to the vehicle body. A hex-head setscrew used as a body-panel fixing, cla...

ATF Cooler Pipe Clip for the automatic transmission oil cooler circuit. The clip secures the automatic transmission fluid (ATF) cooler pipe, holdi...

Clip

Air Cleaner Retaining Clip for the air filter housing, securing the housing cover to its body. The clip clamps the air cleaner lid closed so the f...

Main Bearing Cap Bolt for the cylinder block bottom end, clamping a main bearing cap to the block and retaining the crankshaft main bearing shells....

baffle 576843

Adhesive Pad is a self-adhesive mounting pad used to bond and locate a small component against a body panel or bracket. It provides a clean fixing...

Spire Nut is a spring-steel captive fastener that clips over a panel edge or into a pierced hole to provide a threaded anchor point for a screw. T...

Exh 58 mm Exh

Layshaft Roll Pin for the manual transmission. This roll (tension) pin locates and retains the layshaft within the gearbox casing, holding the sha...

Exh 60 mm Exh

Screw used as a threaded fastener within the fuel system and throttle assembly of the 3.5L V8 twin-carburettor petrol engine.

Gearchange O-Ring for the automatic transmission gearchange assembly. This O-ring forms a seal at the gearchange selector shaft interface, keeping...

Gearchange E-Clip for the automatic transmission gearchange linkage. This external E-clip seats in a machined groove on a pivot pin to retain the ...

Wiring Harness Clip - clip that retains and routes the wiring harness. Secures the harness to its mounting points, keeping the loom located and pr...

Self-Tapping Screw for body hardware fixing, used to secure the exterior door handle. The self-tapping thread forms its own mating thread as it is...

Nut - a threaded fastener that tightens onto a matching bolt or stud to form a secured joint.

Handbrake Sealing Gasket for the parking brake (handbrake) assembly. The gasket seals the mating joint between the handbrake lever body and its mo...

Screw - a flanged-head screw used across a range of applications. The integral flange beneath the head spreads the clamping load over a wider bear...

Plain Washer used under a bolt head or nut to distribute clamping load and protect the mating surface.

Washer is a component within the air suspension air supply and control assembly. It is used at a fastening or connection point among the air suspe...

Lamp Grommet is a rubber grommet fitted at the side and flasher (front indicator) lamp mounting. It seals the aperture where the lamp wiring passe...

Seat Belt Bolt Cap is a trim cover that fits over the head of a seat belt anchor bolt. It conceals the mounting bolt at a seat belt anchorage poin...

Door Lock Clip is a retaining clip that operates within the rear end door lock assembly. It secures the lock components in position within the rea...

Set Screw - threaded fastener used as a general fixing on Land Rover Series assemblies. Sold individually.

Screw - M4 x 16mm metric machine screw used as a general fixing. A multi-application fastener rather than a component-specific part; the same scre...

Sill Lock Button for the door locking mechanism. The pull-up button mounted on the door sill trim that connects to the door latch, allowing the do...

Spring Washer - Side Repeater Lamp A spring washer used at the side repeater lamp mounting. Fitted beneath the securing nut or screw, it maintains...

Hose Clip A clip that secures a flexible hose onto its connecting spigot or fitting. It retains the hose in position and maintains a consistent co...

Heater Assembly Clip A retaining clip used within the heater (HVAC) assembly to hold adjoining components of the heater box together. It secures t...

Stud A threaded stud fastener that screws into a tapped hole at one end to provide a fixed threaded projection. The exposed end accepts a nut, cla...

Plain Washer A flat washer that seats beneath a bolt head or nut to distribute the fastener's clamping load across a wider area of the mating surfa...