Price <10

Inlet Manifold O-Ring for the 2.5L 6-cylinder BMW diesel engine (M51). This O-ring seals the joint at the inlet manifold, preventing air ingress t...

Fastener used to secure interior door casing panels and body side trim. Retains door casing and rear body panel trim on applicable vehicles.

Wiper Hole Blanking Plug - Plenum Air-Take Extension for the Discovery 2 (L318). This rubber blanking plug seals an unused aperture in the plenum ...

Clip - a small retaining clip used within the transfer box differential lock linkage and at the handbrake lever and clutch master cylinder mounting...

Washer 577254

Fusible Link is a high-current circuit-protection device fitted in the engine compartment fuse box. It protects heavy-current wiring and the downs...

Turbo To Manifold Gasket for the Range Rover Classic fitted with the 2.4 or 2.5 litre VM Diesel engine. This gasket seals the joint between the ex...

Flanged Clip Nut is an M6 captive nut retained in a spring-steel clip. The clip pushes onto a panel edge or into a mounting hole to hold the nut c...

Bonnet Staple - the fixed engagement point within the hand-operated bonnet locking assembly. This component mounts to the bonnet panel and interfa...

Circlip - the rear hub bearing lock ring in the rear suspension knuckle. It seats in a groove in the knuckle bore to retain the rear hub bearing a...

Bolt, high tensile, M8 x 25mm. A metric hexagon head bolt for body, chassis, and structural fastening applications.

Flasher Unit - 12V - 2-Pin for Land Rover direction indicator circuits. This 12-volt, 2-pin flasher relay controls the timed switching of the indic...

EGR Tube Clamp for the 2.2L DW12 diesel engine, part of the exhaust gas recirculation circuit. The clamp secures the EGR tube to its mating connec...

Oil Pump Screw secures the oil pump assembly within the lubrication system of the 2.25L 4-cylinder petrol engine.

Facia Assembly Fastener - a fastener for mounting the facia assembly to the dash structure. It secures the facia panel in place and is also used t...

Hex Nut

Bulb & Holder

Hex Flange Nut - a flanged hexagonal nut used as a general threaded fastener across multiple vehicle assemblies. The integral flange spreads the c...

Locking Washer

Sealing Washer fitted at the engine front cover. Provides a leak-tight seal at a fastener or fitting on the front cover assembly.

Nut - M5 x 12mm is a threaded securing nut with an M5 thread. It is a multi-application fastener used across a range of body, door and electrical ...

Upper Tailgate Screw, a fixing used in the upper tailgate assembly. It secures the upper tailgate components in place, providing a threaded fasten...

Plain Washer - 7/16" used in the power steering box assembly. This flat washer is used within the steering hydraulic assembly at the power steerin...

Screw - M6 metric fixing screw, 30 mm long. A general-purpose threaded fastener used to secure body panels, door-frame fittings and other bolted a...

Diesel Fuel Filter Plug Seal - a sealing ring for the drain plug on the diesel fuel filter and sedimentor. It seals the drain/bleed plug against t...

Clip - Door Lock & Handle A retaining clip used within the door lock and handle assembly. It secures the operating rod that links the door han...

Bolt, a threaded fastener used on the 2.0L petrol engine.

Clip - a retaining clip within the vehicle body hardware, used to secure and locate a fitted component in position.

Gearbox Selector Circlip - a retaining circlip within the manual transmission gear selector mechanism. The circlip locates on its shaft to secure ...

Brake Light Switch

Crankshaft Main Thrust Bearing controls the axial, fore-and-aft movement of the crankshaft within the cylinder block. It sets crankshaft end-float ...

Valve Stem Seal for the Rover V8 engine, part of the cylinder head valve train. The seal fits over the top of the valve stem where it passes throu...

Clip is a fastening used within the body moulding assembly, retaining exterior trim and moulding panels against the bodywork.

Shim 1.65mm for Layshaft Speed - V8 4

Washer - M4 flat washer, used to spread the clamping load of an M4 fastener and protect the panel surface beneath the fixing. Fitted at a number o...

Brake Pipe Clip secures and routes rigid brake pipe runs within the braking system, holding the pipe against the chassis or body to maintain its ro...

O-Ring for the air conditioning refrigerant circuit, used at the pipe and hose unions through the system including the condenser and evaporator con...

Exhaust Pipe Clamp for the front exhaust pipe joint. Clamps the front exhaust pipe at its connection, holding the joint tight and gas-tight agains...

Asy Lamp

Side step insulator - a moulded pad that sits between the side step mounting bracket and the vehicle body, within the deployable side step mounting...

Bush - Steering Column