Range Rover Classic Parts

Water Pump Pulley for the 2.5L 300 TDi turbocharged diesel engine, mounting to the water pump hub within the engine cooling circuit. The pulley is...

Alloy Wheel, 16 x 7 inch, finished in gloss black. The wheel has a positive offset of ET+11 (11 mm) and a rated load capacity of 1,400 kg per whee...

Injector Dowel Ring for the fuel injection system of the 2.5L 200 TDi engine. This locating dowel positions the injector correctly in the cylinder...

Pivot Lever Pin is the selector pivot pin in the LT230 transfer box, providing the pivot point about which the range selector lever swings. It loc...

Oil Pump Bolt for the Rover 3.5L V8 petrol engine, 1/4" UNC x 1 1/4". The bolt secures the oil pump to the timing cover, retaining the pump body th...

Rear Coil Spring for the rear suspension, raising ride height by approximately 40mm over standard. Wound from 18mm wire with a free height of 445m...

Weld-On Beadlock Ring Kit - a set of four steel beadlock rings for converting 16in steel wheels to a mechanically clamped tyre bead. The inner rin...

Exhaust Valve for the cylinder head valvetrain of the 200TDi and 300TDi 2.5L turbo diesel engines. It seats in the cylinder head exhaust port and ...

Layshaft Bearing for the front of the LT77 five-speed manual gearbox layshaft. The bearing supports the forward end of the layshaft (countershaft)...

Polyurethane Suspension Bush Kit - Classic Red grade. This kit replaces the original rubber suspension bushes with polyurethane items in the Polyb...

Drain Plug Washer is the copper sealing washer for the drain plug on the LT77 manual gearbox. It seats between the magnetic drain plug and the gea...

Thrust Washer is a 1.05mm selective thrust washer for the centre differential of the LT230 transfer box. It sets the end-float of the centre diffe...

Shock Absorber - front gas-charged suspension damper. Mounted between the front axle and the chassis, it damps spring oscillation to control body ...

Fuel Pipe Olive is a compression ferrule used to seal a rigid fuel pipe union. The olive is compressed onto the pipe by the union nut to form a le...

Shock absorber rear Pro-Comp gas 0-25 mm (+1")

Selector Cover Gasket - LT95

Drain Plug - a threaded plug that seals a drain point and is removed to drain fluid during service. It is used in several locations depending on ap...

Oil Pump Gasket for the LT95 four-speed gearbox. It seals the oil pump to the gearbox casing on the LT95 transmission, used behind the Rover V8 an...

Piston Ring (+.020" Oversize) for the 2.5L 200 TDi four-cylinder turbo diesel engine, forming part of the piston, connecting rod and bearing assemb...

Locking Nut for the steering linkage, retaining a track rod end onto the drag link or track rod. Once the joint is set to position, the nut is tigh...

Locking Nut, a self-locking fixing used across body trim, door casings and bumper fixings. The locking feature resists loosening under vibration.

Differential Bearing Shim - 0.063in

Cylinder Head Bolt for the Rover V8 engine, 7/16" UNC thread. Used to secure the cylinder head to the block on the Rover 3.5L, 3.9L and 4.0L V8 en...

Rear Coil Spring for the rear suspension, a heavy-duty rating that raises ride height by approximately 40mm over standard. The increased free leng...

Wing Nut for the air cleaner assembly. This threaded wing nut secures the air cleaner cover to its centre stud, clamping the cover down to retain ...

Mainshaft Circlip for the LT77 and LT85 five-speed manual gearbox. It seats on the mainshaft to retain a gear or bearing in position, fixing axial ...

Plain Washer A flat plain washer that spreads the clamping load of a fastener over the mounting surface. Used in body panel and interior fixings.

Spring Nut - Metal U-Clip for body panel and electrical component fixings across a range of Land Rover models. This metal U-clip spire nut clips o...

Air Ram - the forward-facing intake head of a raised air intake (snorkel) system, in 3" diameter. Mounted at the top of the snorkel body, it draws...

Fusible Link is a sacrificial circuit-protection device used in the vehicle electrical system. Rated at 60A and identified by its yellow body, it ...

Dowel is a hollow locating dowel ring that aligns two mating housings during assembly, holding their faces in register and taking shear load off th...

JATE Ring Recovery Points - heavy-duty steel rings that replace the original chassis lashing eyes to provide rated vehicle recovery points. The JA...

Fuel Injector for the fuel injection system of the 2.5L 200 TDi diesel engine (reconditioned). The injector atomises high-pressure diesel delivere...

Bolt Hex-head fastener, M10 x 100mm, used as a chassis and crossmember fixing. Commonly fitted to secure the gearbox crossmember, and used across ...

Cylinder Head Bolt - a 7/16" UNC long-type bolt for the Rover V8, part of the cylinder head fixings. This is the longest of the head bolts used on...

Hose Clip clamps a hose onto its spigot or fitting, maintaining a sealed joint under pressure.

Cranked Rear Radius Arm - links the rear axle to the chassis, controlling fore-and-aft axle location and reacting drive and braking torque. The cr...

Front Half Shaft Pair for the front axle drive, transmitting torque from the front differential out through the axle casing to the wheel hubs. The...

Pair of Heavy Duty Rear Half Shafts for 90/Discovery 1/RRC 1994 On & 110/130 2002 On

Front Shock Absorber for the front axle suspension assembly, controlling vertical wheel movement and stabilising the coil spring through compressio...

Track Rod Washer from the steering linkage. It seats at the track rod fixing, spreading clamp load beneath the retaining nut to secure the joint.

Shock Absorber Boots are protective covers that fit over the shock absorber body to shield the shaft and seal from mud, grit and debris. Supplied ...

Steel Road Wheel - 7 x 16 pressed-steel wheel in the 8-spoke pattern, finished in silver, ET00 offset. The pressed-steel construction withstands o...

Locking Wheel Nut Set secures the road wheels to the hub with a keyed nut pattern that cannot be removed with a standard socket, deterring wheel th...

Steel Road Wheel - 7 x 16 pressed-steel wheel in the modular pattern, finished in white, ET08 offset. The pressed-steel construction withstands of...

Steel Road Wheel - 7 x 16 pressed-steel wheel in the 8-spoke pattern, finished in white, ET00 offset. The pressed-steel construction withstands of...

Steel Road Wheel - 7 x 16 pressed-steel wheel in the 8-spoke pattern, finished in black, ET00 offset. The pressed-steel construction withstands of...