Range Rover Classic Parts

Drive Flange for the front hub assembly. The drive flange bolts to the outer face of the hub and engages the splined end of the axle half shaft, t...

Washer Jet Tubing is the flexible hose used within the windscreen washer system, supplied in 1 m lengths. It carries washer fluid from the reservo...

Brake T-Piece - Metric is a three-way junction in the brake hydraulic circuit. It joins three brake pipes at a single union, typically distributin...

Headlamp Body with manual headlamp levelling. The headlamp body is the housing and reflector unit that carries the headlamp light unit and mounts ...

kit parts fixing headlamp

Exhaust Spacer Tube is a short pipe section within the exhaust system. It spaces and connects adjacent exhaust sections at a flanged joint, settin...

Wheel Spanner - 24mm for removing and fitting wheel nuts on Land Rover vehicles. This 24mm spanner is sized for the standard wheel nut used across...

Track Rod End for the steering linkage, with a left-hand thread. The track rod end forms the ball-jointed connection between the steering link and...

Oil Temperature Transmitter for the engine instrumentation circuit. The transmitter threads into the oil gallery and varies its electrical resistan...

Oil Pump Gasket for the engine lubrication system, sealing the oil pump to its mounting face on the cylinder block. It maintains a leak-free joint...

High Note Horn, the high-pitched unit of the vehicle's dual-tone horn system. It sounds together with the low note horn to produce the two-tone au...

Plain Washer with a 6 mm (1/4") bore, a general-purpose flat washer for use with M6 fasteners. Fitted beneath a bolt head or nut to spread the cla...

Tab Washer locks the drop arm retaining nut on the Adwest power steering box, its tab folded against a flat on the nut to stop it working loose und...

Set Screw, a hexagon-head metric fastener, M10 x 25mm. In Land Rover terminology a set screw is a bolt threaded along its full length rather than ...

Screw M6 x 20 pan-head screw. It can be used in place of LR083229 (RYG500650 / DYP500210 / EYG50080) but is not identical: this screw has no capti...

Plain Washer - a flat, load-spreading washer with a 1/4 in (6 mm) bore and 5/8 in outside diameter, approximately 1/16 in thick, finished in Sherar...

Bleed Screw - Metric is the bleed nipple for a disc brake caliper. Threaded into the caliper body, it is opened during brake bleeding to release t...

Headlamp Rim is the outer trim bezel that surrounds and retains the headlamp unit in the front panel, finished in chrome. It locates over the head...

Drive Belt for the auxiliary (accessory) drive system of the 300 TDi turbo diesel engine. The belt transmits drive from the crankshaft pulley to th...

Nyloc Nut with an M16 thread - a nylon-insert locking nut used on heavily loaded suspension and driveline fixings. A nylon collar set into the top...

Fuel Filter Housing Assembly for the fuel delivery line on carburettor petrol engines, including the 3.5L V8. This assembly mounts in-line between...

Wiper Delay Relay for the front windscreen wiper circuit, controlling the intermittent (delay) wipe function. It times the pause between wipe cycl...

Needle Roller Bearing for the front axle swivel pin housing. The bearing seats in the swivel housing bore and carries the stub axle, providing rad...

Brake Disc - Solid - Front is the front brake disc, mounting to the wheel hub and providing the friction surface the brake pads clamp against durin...

Camshaft Oil Seal seals the camshaft on the 2.5L 4-cylinder diesel engines, including the 200TDi. Fitted at the front of the engine where the cams...

Plenum Hose - Breather T-Piece to Plenum

Turbo Oil Drain Gasket seals the turbocharger oil return on the 2.5L 300TDi. Fitted at the joint between the turbocharger oil drain (return) pipe ...

Interior Door Handle for the right-hand side. Part of the door latch and release mechanism. Mounted on the inner door, the handle operates the lat...

Alternator 300TDi (with pulley)

Headlamp Adjuster for the manual headlamp levelling system, fitted to the headlamp unit. It sets the vertical aim of the headlamp beam, allowing t...

Oil Seal – Rear Output Shaft seals the rear output shaft of the LT95 combined gearbox and transfer box, preventing oil leakage where the shaft exit...

Brake Pipe Clip - Double

Core Plug for the V8 petrol cylinder block and inlet manifold. The cup-type plug seals the casting core holes left in the coolant jacket after man...

Core Plug (cup/expansion plug) seals a casting core hole in the cylinder block, fitted at the rear of the block. It closes the openings left by th...

Ball Joint for the self-levelling suspension strut. Forms the pivoting connection at the end of the self-levelling unit, letting the strut articul...

Track Rod & Steering Damper Bush for the steering linkage, locating the steering damper at its mounting eye. The bush insulates the damper mou...

Grommet - a rubber panel grommet providing a sealed, protected pass-through for the choke cable and windscreen washer tubing. Fitted into the pane...

Core Plug for the cylinder head, sealing a core hole left in the casting during manufacture. It closes the opening left by the casting sand core a...

Spring plate

Handbrake Locking Plate for the rod-operated transmission handbrake - the drum-type parking brake mounted at the transfer gearbox output. The plat...

Carpet Drive Clip is an interior trim fastener used to retain the floor carpets against the body. The drive-clip design presses into a mounting ho...

Glass Fuse - 25A - a 25 A glass cartridge fuse for the vehicle's electrical circuits. The glass body carries a calibrated wire element between two...

Wheel Centre Cap in a Silver Sparkle finish with the embossed Land Rover logo, fitting the centre bore of the alloy road wheel. It conceals the hub...

Steering Drop Arm Puller - a specialist tool for drawing the drop arm off the splined output shaft of the steering box. The drop arm is a tight ta...

Air intake duct hose Def 2.5DT & 200TDi air cleaner to turbocharger

Rear Brake Caliper for the left-hand side of the rear axle, part of the hydraulic braking circuit. The caliper carries the hydraulic pistons that ...

Nut - an M10 self-locking hex nut used in the exhaust system to secure flanged joint and manifold connections. The self-locking feature resists lo...

O-Ring for the power steering hydraulic circuit, sealing a union on the 6mm power steering pipe. The O-ring seats at the connection between the po...