Range Rover Classic Parts

Camshaft Bearing Set for the Rover V8 petrol engine. This set provides the bearing surfaces on which the camshaft journals run within the cylinder...

A-Frame Ball Joint Boot is the protective gaiter that seals the ball joint at the apex of the rear suspension A-frame. The A-frame locates the rea...

Pipe and Hose Retaining Clip - Engine is a small-bore clip used to retain pipes and hoses at multiple points across the engine bay and fuel system ...

Wiper Switch - Column is the steering-column stalk switch that controls the windscreen wash/wipe function. Mounted on the steering column, it sele...

Tensioner Pulley for the air conditioning drive belt on the 2.5L 300TDi turbo diesel engine. It runs against the accessory drive belt and maintain...

Hose Clip for radiator hose connections on 4-cylinder TDi diesel engines. This screw-type hose clip secures the upper and lower radiator hoses at ...

Rear Brake Caliper, right-hand side, for the rear braking circuit on models fitted with solid (non-vented) rear discs. The caliper clamps the brake...

Piston Ring Set for the 300TDi diesel engine, supplied in standard size. The set provides the compression and oil control rings for one piston. Fo...

Washer - Diesel Sedimentor is a sealing washer used in the diesel fuel sedimentor (fuel filter/water separator) assembly on diesel-engined Land Rov...

Timing Belt Tensioner for the 200TDi 2.5L turbo diesel engine, part of the camshaft timing belt drive. The tensioner maintains correct tension on ...

Gearbox Filter Plug for the LT77 five-speed manual gearbox. The plug closes the bore in the extension case that gives access to the gearbox oil fil...

Headlamp Assembly is a complete halogen front headlamp unit within the exterior lighting system, supplied with its integral manual levelling mechan...

Banjo bolt

Clutch Kit is a matched three-piece clutch assembly for the 3.5L V8 petrol engine with manual transmission. The kit renews the complete clutch as ...

Head Gasket Set - V8

Ignition Module & Link Lead - a kit for the 3.5L Rover V8 petrol engine ignition system, comprising the electronic ignition module (amplifier) ...

Differential Assembly - a reconditioned 4-pin differential unit for the Land Rover-type axle. The differential sits at the centre of the axle, tak...

Brake Caliper Piston Kit - replacement pistons for the rear brake caliper. The pistons run in the caliper bores and, under hydraulic pressure, pre...

Rear Coil Spring Spacers, +2" - a pair of suspension spacers for the rear coil springs that raise ride height by approximately 2 inches (50 mm). E...

Headlamp Mounting Gasket for the headlamp assembly. A rubber gasket that seats between the headlamp unit and the body aperture surround. It provid...

Engine Coolant, pre-mixed for use in the engine cooling system. It circulates through the radiator, water pump and heater circuit to regulate opera...

Heavy Duty spring Range Rover rear +0mm

Crankcase Breather Hose forms part of the closed crankcase ventilation circuit, connecting the rocker cover breather outlet to the intake manifold ...

Steering knuckle fulcrum bracket assembly used within the front axle swivel and steering knuckle pivot arrangement. The bracket forms the lower p...

Main Bearing Cap Bolt - a 1/2" UNC bolt that fastens a main bearing cap to the cylinder block on the Rover V8 engine. It clamps the main bearing c...

Edge Clip - push-on edge clip that grips the flange of an interior trim panel, retaining both the panel and the wiring harness routed along its edg...

Flange Bolt - M8 x 130mm, used to secure the coolant pump (water pump) on the 2.5L 300 TDi diesel engine. The integrated flange beneath the head s...

Cable Tie for securing wiring harnesses and cable runs throughout the vehicle.

Split Pin: a cotter pin that locks a slotted (castle) nut or retains a clevis pin. After fitting, its legs are bent back to stop the fastening work...

A-Frame Ball Joint Bracket forms the pivot connection at the apex of the rear axle A-frame linkage. It mounts to the rear axle housing and locates ...

Radius Arm Bush mounts the front radius arm to the axle within the suspension linkage, at the axle end of the arm. The bush provides a flexible pi...

Coolant Expansion Tank with a clear (translucent) body, part of the engine cooling system. The tank serves as the system's pressurised reservoir a...

Main Bearing Set for the 2.5L 4-cylinder engine (200 TDi, 300 TDi and the related 2.5 diesel and petrol units), supplied at standard size. The mai...

Connecting Rod Bearing Set for the Rover V8 petrol engine. These are the big-end bearing shells that sit between the connecting rods and the cranks...

Pinion Bearing - 35 × 68.5mm, a tapered roller bearing installed on the Constant Mesh Pinion shaft within the LT77, R380, and LT95 manual gearboxes...

Reverse lamp switch LT85 V8

Connecting Rod Bearing Set for the 2.5-litre 4-cylinder engine, including the 200 TDi and 300 TDi diesels. These are the replaceable big-end shell ...

Piston Ring Set supplies the sealing rings for one piston of the 3.5L V8 petrol engine, in standard (non-oversize) bore size. The rings seal the p...

Bottle sensor

Clutch Driven Plate for the V8 clutch assembly. It is carried on the gearbox input shaft between the flywheel and the clutch cover (pressure plate)...

Exhaust Bracket supports and locates a section of the exhaust system against the underbody. It carries the weight of the exhaust at its mounting p...

Alloy Wheel is a single-piece 16 x 7-inch alloy road wheel finished in black. It has a five-stud 5x165 mm bolt pattern and an ET20 offset, which s...

Steering Box Oil Seal Oil seal for the input (worm) shaft of the manual, non-power (Gemmer) steering box, sealing around the shaft where it enters ...

Gearbox Side Cover Gasket for the LT95 4-speed V8 gearbox. This gasket seals the side cover to the gearbox casing, preventing oil leaks from the ge...

Flange Bolt is an M8 x 35 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Blanking Plug - a push-fit plug used to close an unused aperture in a body panel, door or interior trim component. It seals the opening against wa...

Bolt - M6 x 30mm is a metric threaded fastener with a 6 mm nominal thread diameter and a 30 mm shank length. It secures bolted joints where an M6 ...

Pull Ring for the rear seat lock release. It operates the split rear seat lock mechanism, releasing the seat squab so the backrest can be folded d...