Range Rover Classic Parts

Coolant Hose - Expansion Tank Vent is the bleed hose in the engine cooling system, connecting the radiator bleed outlet to the coolant expansion ta...

Gear Diff Kit

Sealing Washer for the front (timing) cover of the 300TDi 2.5L turbo diesel engine. It provides a fluid-tight seal at the front cover, fitted unde...

Power Steering Pump is the engine-driven hydraulic pump at the heart of the power-assisted steering circuit on the 300 TDi 2.5L turbo diesel. Belt...

Switch - Window Lift - Centre Console - Discovery 1/RRC

Wheel Nut - road wheel nut, black finish. Clamps the road wheel against the hub face on the wheel studs. The seat profile is specified for alloy r...

Water Pump for the 3.5L V8 petrol engine, part of the engine cooling circuit. Mounted to the front timing cover and belt-driven from the crankshaf...

Radius Arm - front axle locating link in the coil-sprung front suspension. The radius arm ties the front axle to the chassis, controlling fore-and-...

Engine Mounting Rubber (V8) supports the V8 petrol engine on the chassis and isolates its vibration from the bodyshell. The bonded rubber-to-metal...

Drive Flange Nut - replacement centre nut for the heavy-duty thin-type drive flange, black finish. The drive flange sits at the outer end of the f...

Camshaft for the Rover V8 EFI petrol engine (3.9L, 4.0L and 4.6L variants). Mounted centrally in the cylinder block, the camshaft is driven from t...

Braided Earth Strip is a flexible braided conductor that forms an electrical earth (ground) bond between two points in the vehicle. It provides a ...

Brake Caliper Seal Repair Kit the seal set for resealing a four-piston brake caliper within the hydraulic braking system. This kit contains the pi...

Second Speed Gear for the LT77 five-speed manual gearbox. It runs on the mainshaft within the first, second and fifth-speed gear group and meshes w...

Anti-roll bar bush used in the front suspension anti-roll bar assembly, providing the compliant mounting interface between the anti-roll bar and it...

Bearing for 2ND Gear Suffix H Onwards and 3RD Gear On - Freelander 1

Synchromesh Assembly First/second gear synchromesh assembly for the LT95 four-speed gearbox. Synchronises shaft and gear speeds during 1st-to-2nd ...

Lazer ST4 Evolution LED Spotlight - a compact four-LED auxiliary driving lamp producing a controlled long-range beam for forward illumination. The...

Coating Spray Gun, bottle-mount type, for applying protective coating. This Schutz-style gun screws directly onto the 750ml coating bottle, so no s...

Rear suspension bush kit covering the trailing arm and A-frame mounting points of the rear coil-sprung suspension. The trailing arms locate the re...

Rear Shock Absorber Mounting Brackets for the rear suspension damper installation, supplied as a pair. These brackets weld to the rear axle housin...

Small-End Connecting Rod Bush for the 2.5L 200 TDi diesel engine. The small-end bush is pressed into the little end of the connecting rod and carr...

Front Axle Panhard Rod Bush - Late Type, for replacement at the Panhard rod mounting point on the front axle assembly. The bush provides the compl...

Primary Pinion Shim sets the installed position of the primary pinion within the LT95 four-speed gearbox (V8) casing. 2.10 mm thick, it controls p...

Serrated Washer, 7/16", used within the clutch master cylinder and pipe assembly. The serrated face bites into the mating surface as the fixing is...

GENUINE LR camshaft sprocket for Rover V8 engines

Main Bearing Set for the Rover 3.5-litre V8 petrol engine. These are the replaceable shell bearings that carry the crankshaft in the cylinder block...

4-Pin Differential for the Land Rover-type axle. The differential takes drive from the propshaft through the crown wheel and pinion and splits it ...

Fuse - 60A - high-current blade fuse for the main electrical protection circuits. Rated at 60 amps, this fuse protects high-draw circuits such as ...

Breather Hose is part of the crankcase ventilation system on the 3.5L V8 twin-carburettor petrol engine. It routes breather gases through the vent...

Engine Mount - Right Hand supports the engine at the right-hand mounting point and isolates engine vibration from the chassis. It locates between ...

Ignition Wiring Harness - the low-tension (LT) link lead within the V8 petrol ignition system. This harness carries the low-tension (primary) side...

Fuel Pump Gasket seals the external fuel pump to its mounting face in the fuel delivery system, preventing leakage at the joint. Used on petrol ap...

rear output shaft LT95 4-speed gearbox V8 - S3 109" Stage 1 V8 - 101" Forward Control - Range Rover Classic 4-speed V8 - Early 110" 4-speed V8

Shim 1.65mm for Layshaft Speed - V8 4

Gearbox Crossmember is a detachable structural member that bolts across the chassis side rails beneath the transmission. It carries the rear gearb...

Headlamp Bowl Seal - the gasket that seals the 7-inch headlamp bowl against the surrounding body panel. Fitted around the lamp aperture, it closes...

Differential Guard - a wrap-around steel guard that shields the front or rear differential housing from impact and debris during off-road use. Des...

First Speed Bush for the LT77 five-speed manual gearbox. This selective-fit bush supports the first-speed gear on the mainshaft, within the first, ...

Piston ring set for the 3.5L Rover V8 petrol engine, supplied per piston. The rings seal the combustion chamber against the cylinder bore, transfe...

PTO Shaft - Centre - the centre shaft in the power take-off (PTO) drive train. The power take-off transmits rotational drive from the transfer gea...

Synchromesh Assembly for 1st and 2nd gear in the LT77 5-speed manual gearbox. Mounted on the mainshaft, the synchromesh matches the rotational spe...

Wading Kit for the drivetrain and engine breather system, extending the breather points of the axles, gearbox and engine to a higher level. Raisin...

Carburettor Needle for the SU variable-venturi carburettor in the fuel system of the 3.5L V8 petrol engine, in twin-carburettor configuration. The...

Drive Screw for use in Land Rover body, chassis, and hardware assembly. A No.14 × 1" drive screw, supplied individually.

O-Ring for the air conditioning refrigerant circuit, used at the pipe and hose unions through the system including the condenser and evaporator con...

Tensioner Pulley Bearing for the auxiliary drive belt system on air-conditioned vehicles. It is the bearing carried within the idler/tensioner pul...