Range Rover Classic Parts

Hylomar Universal Blue is a non-setting gasket jointing compound for use on gaskets and machined metal joint faces in automotive and engineering ap...

Differential Pinion Oil Seal with a double sealing lip, for the front and rear differentials. It is press-fitted into the differential housing aro...

Swivel Pin Housing Oil Seal - 9mm seal fitted to the front axle swivel housing. It seals the point where the drive shaft enters the swivel housing...

Rocker Cover Gasket for the 2.5L 300TDi diesel engine, sealing the interface between the rocker cover and the cylinder head. Installed at the top ...

Clutch Release Staple is the spring retaining clip that secures the clutch release bearing assembly to the clutch fork, holding the bearing in posi...

Radius Arm Bush - Rear, Lower - the compliant mount at the lower link of the rear radius arm, between the arm and its chassis bracket. The rear ra...

Inlet Manifold Gasket for the V8 petrol engine, forming the seal between the central inlet manifold casting and the cylinder head intake faces. It...

Fulcrum Bracket and Ball Joint Assembly for the rear A-frame (top link). The bracket forms the apex of the A-frame and bolts to the rear axle; the ...

Oil seal designed to retain lubricant and prevent contamination at the stub axle interface. The seal fits into the stub axle and forms a barrier b...

Shock absorber bush (eye), anti roll bar bush

Brake Pad Fitting Kit for front brake assemblies running vented discs. The kit supplies the retaining hardware that secures and correctly positions...

Hex Nut - 3/8" UNF - Full is a full-height plain hexagonal nut with a 3/8 inch UNF thread, used as a load-bearing imperial-thread fastener. It is ...

Exhaust Gasket - V8 for the exhaust downpipe assembly on V8 petrol engines. This gasket seals the flange joint at the exhaust downpipe, maintainin...

Exhaust Gasket for the front exhaust section on 2.5L TDi and V8 petrol engines. On 2.5L 200 TDi and 300 TDi 4-Cylinder engines this gasket seals t...

Steering Damper Stabiliser - a hydraulic damper fitted within the steering linkage assembly to control the oscillation and vibration transmitted th...

Track Rod End Boot - Polyurethane for the steering track rod end ball joint. This polyurethane boot fits over the track rod end housing, sealing t...

Water Pump for the 300 Tdi 2.5L turbo diesel engine cooling circuit. The pump bolts to the engine front cover and circulates coolant through the cy...

Circlip for the drive shaft and hub assembly on Land Rover permanent four-wheel drive axles. This circlip locates in a machined groove on the driv...

Joint Washer - front timing cover gasket for Land Rover 4-cylinder petrol and diesel engines. This gasket seals the mating face between the front ...

Spring Washer fitted under a nut or bolt head to resist loosening from vibration. An M8 split-ring (single-coil) spring washer. The sprung opening...

Thermostat for the 2.5L 300TDi diesel engine, operating within the thermostat housing at the top of the cooling circuit. The thermostat regulates ...

Reverse Lamp Bulb - a 21W 12V single-filament incandescent bulb (type P21W) with a BA15s single-contact bayonet cap, fitted to the rear lamp assemb...

Track Rod End with a right-hand thread, forming part of the steering linkage. The track rod end is the articulating ball joint that connects the t...

Low Note Horn, a 335 Hz electric horn within the audible warning circuit. Produces the low-frequency tone of a dual-tone horn arrangement, pairing...

Transmission Brake Dust Cover for the central handbrake drum on the transmission output shaft. This cover shields the handbrake drum and brake sho...

Fir Tree Fastener in Dark grey, for the roof trim and headlining assembly. Push-fit fastener that secures roof trim panels and headlining ancillar...

Transfer Box Gear Lever Knob fitted to the LT230 transfer box gear lever in vehicles where the LT230 is paired with the LT77 main gearbox. The lev...

Locknut for body and trim panel fixings. It seats into a pre-formed aperture in the panel to provide a captive threaded point for the screws or bo...

Differential Carrier Gasket for the Rover-type axle assembly. The gasket seals the differential carrier housing against the axle casing at the cen...

Spire Clip used to retain front wing panels and heater assembly components. This spring-steel clip slides over a screw or stud thread and grips se...

Nyloc Nut with a 5/8" UNF thread, used as a self-locking fastener in the suspension linkage. The nylon insert deforms around the bolt thread on as...

Door Casing Stud for the interior door casing assembly. Locating stud onto which the door casing mounts, retaining the trim panel and holding it i...

Water Pump Housing Gasket for the 300 TDi cooling circuit, sealing the coolant pump distance piece to the cylinder block. The gasket forms the coo...

Worm-drive Hose Clip with a 32-50 mm clamping range, used to secure a flexible hose to a rigid pipe stub or spigot. Tightening the worm screw draws...

Fuel Pump Kit for the mechanical diesel lift pump in the low-pressure fuel supply circuit of 2.5L naturally aspirated diesel, 2.5L turbo diesel and...

Split Pin locks a castellated (slotted) nut in place, passing through the nut slots and a cross-drilled hole in the shaft to stop the nut working l...

This taper roller bearing is designed for installation in the lower swivel pin housing, providing controlled rotational support and load distributi...

Radiator Mounting Bush is the rubber isolation bush that secures the radiator to the body or chassis mounting points, preventing direct metal-to-me...

Upgrade your Series Land Rover suspension with this Polyurethane Shock Absorber Bush Set in black. The set includes 4 pieces, providing everything ...

Automatic Transmission Oil Screen Kit for the ZF 4-speed automatic transmission, serving the fluid filtration circuit within the transmission sump....

Wheel Nut securing a road wheel to the hub, clamping the wheel against the hub mounting face. M16 internal thread and steel construction, to the s...

Copper Sealing Washer for the oil drain plug of the LT77 and R380 manual gearboxes. The washer forms a leak-free seal between the drain plug and t...

Oil Filler Plug serving as the combined fill and level check point for the swivel pin housing, manual gearbox gearcase, and LT230 transfer box on L...

Injector Sealing Washer seals each fuel injector into the cylinder head within the diesel fuel injection system, for 200 TDi and 300 TDi turbo-dies...

Breather Hose for the 300 TDi crankcase ventilation system. The hose carries crankcase breather (blow-by) gases from the engine breather outlet ba...

Bolt, M10 x 45 securing the front drive member to the hub. The drive member transmits torque from the axle shaft to the road wheel, and these bolts...

Universal Joint for the propshaft, transmitting rotational drive between shaft sections while accommodating the angular movement of the driveline. ...

Stepper Motor - idle air control valve for the V8 multi-point fuel injection system. Mounted on the plenum chamber, it meters the air bypassing th...